Dodge Durango (HB). Manual — part 1412
RISER-FRONT
REMOVAL
Manual Length Adjuster
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
2. Remove the seat. (Refer to 23 - BODY/SEATS/
SEAT - REMOVAL)
3. Move the seat to the forward position on the tracks
and remove the seat adjuster bolts/nuts (3).
4. Move the seat to the reward position on the tracks
and remove the front seat adjuster bolts/nuts (3).
NOTE: Passenger seat with strain gauges shown,
drivers side seat similar.
5.
Disconnect strain gauge electrical connectors (1),
if equipped.
6. If equipped, remove the strain gauge bolts (2) and
remove the strain gauges as necessary.
Power Length Adjuster
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
2. Unbolt the seat from the floor as necessary to gain
access to the riser bolts. (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL)
3. Move the seat to the forward position on the tracks,
tip the seat backwards in vehicle and remove the
seat adjuster bolts/nuts (3).
4. Move the seat to the reward position on the tracks
and remove the front seat adjuster bolts/nuts (3).
NOTE: Manual seat length adjuster shown, power
similar.
HB
SEATS
23 - 161
5. If the seat cannot be moved forward or backward,
remove the seat cushion. (Refer to 23 - BODY/
SEATS/SEAT CUSHION COVER - REMOVAL)
6. Remove the four bolts (1) and remove the motor
and cable assembly (2) from the length adjuster
assembly.
CAUTION: When the motor and cable assembly
are removed from the tracks discard the length
adjuster assembly and replace with a new one.
7. Disconnect and isolate battery negative cable.
8. Remove the seat off of the risers and disconnect
the electrical connectors.
9.
Disconnect strain gauge electrical connectors (1),
if equipped.
10. If equipped, remove the strain gauge bolts (2) and
remove the strain gauges as necessary.
23 - 162
SEATS
HB
INSTALLATION
Manual Length Adjuster
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
NOTE: Passenger seat with strain gauges shown,
drivers side seat similar.
2. If equipped, install the strain gauges and install the
bolts (2).
3. Tighten the bolts to 40 N·m (30 ft. lbs.).
4. If necessary, connect the electrical connections (1).
5. Move the seat to the forward position on the tracks
and install the rear seat adjuster bolts/nuts (3).
6. Tighten the bolts to 45 N·m (33 ft. lbs.).
7. Move the seat to the reward position on the tracks
and install the front seat adjuster bolts/nuts (3).
8. Tighten the bolts to 45 N·m (33 ft. lbs.).
9. Install the seat. (Refer to 23 - BODY/SEATS/SEAT
- INSTALLATION)
Power Length Adjuster
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
2. If equipped, install the strain gauges and install the
bolts (2).
3. Tighten the bolts to 40 N·m (30 ft. lbs.).
4. Position the seat into the vehicle onto the risers
and connect the electrical connectors.
5. Move the seat to the forward position on the tracks
and install the seat adjuster bolts/nuts (3).
6. Tighten the bolts attaching the adjuster to the ris-
ers/strain gauges to 45 N·m (33 ft. lbs.).
7. Move the seat to the reward position on the tracks
and install the front seat adjuster bolts/nuts (3).
8. Tighten the bolts attaching the adjuster to the ris-
ers/strain gauges to 45 N·m (33 ft. lbs.).
9. If necessary, connect the strain gauge electrical
connections (1).
CAUTION: When the motor and cable assembly are removed from the tracks discard the length adjuster
assembly and replace with a new one.
10. Bolt the seat to the floor. (Refer to 23 - BODY/SEATS/SEAT - INSTALLATION)
HB
SEATS
23 - 163
SEAT-SECOND ROW
REMOVAL
1. Position the front seat to the full forward position.
2. Release and fold seat forward.
3. Turn the hinge pin (3) clockwise and disengage
from the retaining tabs (2).
4. With pin (1) released from the retaining tabs, tap
pin out of the spring (2) and remove.
5. Twist the seat assembly up and out of the outboard
hinge (1) and disengage from the inner hinge (2)
and remove seat.
23 - 164
SEATS
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст