Dodge Durango (HB). Manual — part 1430
Without front hinges:
1. Position wind deflector assembly (1) into the roof
opening (2) and slide forward to the mounting point
in the u-frame.
2. Position the wind deflector hinges (1) into the
u-frame at the notch (2) and secure down into the
channel fully.*Right side hinge shown, left side sim-
ilar.
NOTE: Placing a small rolled up piece of paper or
equivalent, between the hinge and the sunroof
opening may aid installation of the wind deflector.
3. Position the front of the wind deflector over the
front hinges and seat down onto the retaining clips
fully.
HB
SUNROOF
23 - 233
TRIM LACE
REMOVAL
1. Remove trim lace (13) by holding one end of the trim lace at the butt joint and pulling horizontally into the open-
ing until lace is completely loose from the headliner/sunroof joint.
23 - 234
SUNROOF
HB
INSTALLATION
1. Place butt joint of trim lace into position starting at the rear of the opening at the butt joint notch (14) in the
u-frame.
2. Push lace into position.
3. Ensure that the corner radii is fully engage.
4. Once the original trim lace is attached to sunroof module using a trim stick C-4755 or equivalent, begin tucking
the headliner under the lip on the trim lace working all the way around the opening. When installing a new trim
lace, begin tucking the headliner under the lip as the tear cord is removed working all the way around the
opening.
HB
SUNROOF
23 - 235
WEATHERSTRIP/SEALS
TABLE OF CONTENTS
page
page
WEATHERSTRIP-FRONT DOOR GLASS RUN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
. . . . . . . . . . . . . . . . . . . . . . . . 236
WEATHERSTRIP-FRONT DOOR BELT INNER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
. . . . . . . . . . . . . . . . . . . . . . . . 236
WEATHERSTRIP-FRONT DOOR BELT OUTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
. . . . . . . . . . . . . . . . . . . . . . . . 237
WEATHERSTRIP-REAR DOOR GLASS RUN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
. . . . . . . . . . . . . . . . . . . . . . . . 237
WEATHERSTRIP-REAR DOOR BELT INNER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
. . . . . . . . . . . . . . . . . . . . . . . . 237
WEATHERSTRIP-REAR DOOR BELT OUTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
. . . . . . . . . . . . . . . . . . . . . . . . 238
WEATHERSTRIP-FRONT DOOR GLASS RUN
REMOVAL
1. Remove glass. (Refer to 23 - BODY/DOOR - FRONT/DOOR GLASS - REMOVAL)
2. Pull the glass run weatherstrip and run channels from the window opening.
3. Pull the glass run weatherstrip from the run channels.
INSTALLATION
1. Install the glass run weatherstrip into the window opening and the run channels.
2. Install glass. (Refer to 23 - BODY/DOOR - FRONT/DOOR GLASS - INSTALLATION)
WEATHERSTRIP-FRONT DOOR BELT INNER
REMOVAL
1. Remove trim panel. (Refer to 23 - BODY/DOOR - FRONT/TRIM PANEL - REMOVAL)
2. Peel seal from door pinch weld.
INSTALLATION
1. Slide seal into position on door.
2. Install the trim panel. (Refer to 23 - BODY/DOOR - FRONT/TRIM PANEL - INSTALLATION)
23 - 236
WEATHERSTRIP/SEALS
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст