Dodge Ram Truck 1500-2500-3500. Manual — part 1931
6. Lower the window regulator (5) and remove the
two nuts (3) that secure the regulator stabilizer (4)
to the door (1).
7. Remove the two bolts (2) that secure the window
regulator to the door and loosen the other two reg-
ulator bolts (6).
8. Slide the window regulator upward and disengage
the two regulator bolts from the door.
9. Remove the window regulator through the opening
in the door.
INSTALLATION
1. Install the window regulator (5) through the opening
in the door (1).
2. Engage the two regulator bolts (6) to the door.
3. Install the two bolts (2) that secure the window reg-
ulator to the door and tighten all four regulator bolts
to 10 N·m (89 in. lbs.).
4. Position the regulator stabilizer (4) onto the door
and install the two nuts (3). Tighten the nuts to 10
N·m (89 in. lbs.).
5. Raise the window regulator (3) to the position
shown and remove the manual window crank.
6. Support the door glass (2) and remove the wooden
wedge or equivalent.
7. Position the door glass to the window regulator and
install the two nuts (1) that secure the door glass to
the window regulator through the sight window (4)
and the speaker opening (5). Tighten the nuts to 10
N·m (89 in. lbs.).
8. Install the waterdam (Refer to 23 - BODY/DOORS
- REAR/WATERDAM - INSTALLATION).
9. Install the inner belt molding (Refer to 23 - BODY/
WEATHERSTRIP/SEALS/REAR
DOOR
INNER
BELT MOLDING - INSTALLATION).
23 - 78
DOORS - REAR
DR/DH
EXTERIOR
TABLE OF CONTENTS
page
page
BODY ISOLATORS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
. . . . . . . . . . . . . . . . . . . . . . . . . 80
BODY SIDE MOLDINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . . . 81
CARGO BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
. . . . . . . . . . . . . . . . . . . . . . . . . 83
CARGO BOX - TIE DOWN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
. . . . . . . . . . . . . . . . . . . . . . . . . 84
COWL GRILLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
. . . . . . . . . . . . . . . . . . . . . . . . . 85
EXTERIOR NAME PLATES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
. . . . . . . . . . . . . . . . . . . . . . . . . 87
FRONT FENDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
. . . . . . . . . . . . . . . . . . . . . . . . . 88
FUEL FILL DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
. . . . . . . . . . . . . . . . . . . . . . . . . 89
GRILLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
. . . . . . . . . . . . . . . . . . . . . . . . . 90
GRILLE FRAME
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
. . . . . . . . . . . . . . . . . . . . . . . . . 91
REAR FENDER-QUAD CAB MODELS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
. . . . . . . . . . . . . . . . . . . . . . . . . 93
SIDE VIEW MIRROR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . . . . . . . . . . 96
SIDE VIEW MIRROR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
. . . . . . . . . . . . . . . . . . . . . . . . . 98
UPPER RADIATOR CROSSMEMBER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
. . . . . . . . . . . . . . . . . . . . . . . . 100
FRONT WHEELHOUSE SPLASH SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
. . . . . . . . . . . . . . . . . . . . . . . . 101
REAR WHEELHOUSE SPLASH SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
. . . . . . . . . . . . . . . . . . . . . . . . 102
BELLY PAN-SRT-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
. . . . . . . . . . . . . . . . . . . . . . . . 103
CLADDING-BODY SIDE - BOX - SRT-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
. . . . . . . . . . . . . . . . . . . . . . . . 104
CLADDING-BODY SIDE - CAB - SRT-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
. . . . . . . . . . . . . . . . . . . . . . . . 106
CLADDING-BODY SIDE - DOOR - SRT-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
. . . . . . . . . . . . . . . . . . . . . . . . 108
CLADDING-BODY SIDE - FENDER SRT-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
. . . . . . . . . . . . . . . . . . . . . . . . 109
SPOILER - SRT-10
DR/DH
EXTERIOR
23 - 79
BODY ISOLATORS
REMOVAL
NOTE: Quad Cab model shown in the illustration.
Body isolators for Regular cab models are similar.
1. Loosen all cab to frame mounting bolts (5) (six
Regular cab, eight Quad Cab).
2. Remove the mounting bolts and rebound cushions
(3) as necessary.
NOTE: If servicing the rear isolators (2), remove
the reinforcement plates (6) and the washers (4).
3. Using a floor jack and wooden block under the cab
sill (1), lift the body to gain access to the isolators
and remove the isolators as necessary.
INSTALLATION
NOTE: Quad Cab model shown in the illustration.
Body isolators for Regular cab models are similar.
1. Position the isolators (2) under the cab as neces-
sary.
CAUTION: If servicing the rear isolators, install the
reinforcement plates (6) and the washers (4).
2. Lower the cab onto the isolators and install the
mounting bolts (5) and rebound cushions (3) as
necessary (six Regular cab, eight Quad Cab).
3. Tighten the mounting bolts to 81 N·m (60 ft. lbs.).
23 - 80
EXTERIOR
DR/DH
BODY SIDE MOLDINGS
REMOVAL
NOTE: Quad Cab model shown in the illustration.
Body side moldings for Regular cab models are
similar.
1. As a guide for installation, apply a length of mask-
ing tape on the rocker panels (1), parallel to the top
edge and, to one end of the body side molding (2
and 3) being removed
CAUTION: Do not exceed 52° C (120° F) when
heating the moldings or rocker panels. Failure to
follow this caution may result in damage to the
moldings and/or the vehicle paint finish.
2. If the temperature is below 21° C (70° F), warm the
body side moldings with a heat lamp or heat gun.
NOTE: The body side moldings are attached to the
cab with adhesive tape.
3. Using a trim stick C-4755 or equivalent, carefully remove the moldings from the rocker panels, as necessary.
INSTALLATION
NOTE: Quad Cab model shown in the illustration.
Body side moldings for Regular cab models are
similar.
1. Thoroughly clean all residue from the molding
attachment areas of the rocker panels (1).
2. Wipe the attachment areas with a clean, lint-free
cloth, moistened with a 50% solution of water and
alcohol and then wipe dry the areas immediately
with a dry, lint-free cloth.
CAUTION: Do not exceed 52° C (120° F) when
heating the moldings or rocker panels. Failure to
follow this caution may result in damage to the
moldings and/or the vehicle paint finish.
NOTE: If ambient temperatures are below 21° C
(70° F), warm the body side molding and rocker
panel with a heat lamp or gun to assure proper
adhesion.
3. Remove the protective covering from the back of the body side molding (2 and 3) and position the molding onto
the rocker panel using the previously installed guide tape.
NOTE: To ensure proper molding adhesion, apply consistent and uniform pressure of approximately 40
p.s.i. over the entire surface of each body side molding.
4. Install the body side molding onto the rocker panel.
DR/DH
EXTERIOR
23 - 81
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст