Dodge Ram Truck 1500-2500-3500. Manual — part 1926
6. Install the latch striker. (Refer to 23 - BODY/
DOORS - REAR/LATCH STRIKER - INSTALLA-
TION)
DOOR GLASS
REMOVAL
1. Remove the inner belt molding (Refer to 23 -
BODY/WEATHERSTRIP/SEALS/REAR
DOOR
INNER BELT MOLDING - REMOVAL).
2. Remove the waterdam (Refer to 23 - BODY/
DOORS - REAR/WATERDAM - REMOVAL).
3. Install the manual window crank or reconnect the
electric window switch to the door wire harness
(depending on application) and raise the door glass
to the position shown.
4. Remove the two nuts (1) that secure the door glass
(2) to the window regulator (3) through the speaker
opening (4) and the sight window (5) and disen-
gage the door glass from the regulator.
23 - 58
DOORS - REAR
DR/DH
5. Remove the two bolts (1) that secure the front
glass run channel (2) to the door and remove the
run channel through the door panel opening.
6. Disengage the door glass from the window regula-
tor and lower the glass into the door.
7. Carefully rotate the door glass within the door and
remove the glass from the window opening.
INSTALLATION
1. Carefully lower the door glass into the door through
the window opening.
2. Rotate the door glass into position and engage it to
the window regulator.
3. Position the front glass run channel (1) into the
door through the door panel opening.
4. Install the two bolts (1) that secure the front glass
run channel to the door. Tighten the bolts to 10
N·m (89 in. lbs.).
DR/DH
DOORS - REAR
23 - 59
5. Install the two nuts (1) that secure the door glass
(2) to the window regulator (3) through the sight
window (4) and the speaker opening (5). Tighten
the nuts to 10 N·m (89 in. lbs.).
6. Lower the door glass into the door and remove the
manual window crank or disconnect the electric
window
switch
from
the
door
wire
harness
(depending on application).
7. Install the waterdam (Refer to 23 - BODY/DOORS
- REAR/WATERDAM - INSTALLATION).
8. Install the inner belt molding (Refer to 23 - BODY/
WEATHERSTRIP/SEALS/REAR
DOOR
INNER
BELT MOLDING - INSTALLATION).
EXTERIOR HANDLE
REMOVAL
1. Remove the front glass run channel (Refer to 23 -
BODY/DOORS - REAR/GLASS RUN CHANNEL -
REMOVAL).
2. Disconnect the actuator rod (1) from the exterior
door handle (2).
3. Remove the two nuts (3) that secure the exterior
door handle to the door and remove the handle.
23 - 60
DOORS - REAR
DR/DH
INSTALLATION
1. Position the exterior handle (2) into the door.
2. Install the two nuts (3) that secure the exterior han-
dle to the door. Tighten the nuts to 10 N·m (89 in.
lbs.).
3. Connect the actuator rod (1) to the exterior handle.
4. Install the front glass run channel (Refer to 23 -
BODY/DOORS - REAR/GLASS RUN CHANNEL -
INSTALLATION).
GLASS RUN CHANNEL
REMOVAL
FRONT
1. Raise the window glass to the full up position and
remove the window regulator (Refer to 23 - BODY/
DOORS
-
REAR/WINDOW
REGULATOR
-
REMOVAL).
2. Remove the two bolts (1) that secure the front
glass run channel (2) to the door and remove the
run channel through the door panel opening.
3. If required, remove the weatherstrip from the front
glass run channel.
DR/DH
DOORS - REAR
23 - 61
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст