Dodge Ram Truck 1500-2500-3500. Manual — part 1891
3. Position the shift motor and mode sensor assembly
onto the transfer case.
4. Install the bolts (3) to hold the shift motor and
mode sensor assembly (2) to the transfer case (1).
Tighten the bolts to 16-25 N·m (12-18 ft. lbs.).
REAR EXTENSION
1. Install new seal in rear extension housing seal with
Installer D-163 and Handle C-4171. Verify that the
weep hole in the rubber is oriented downward.
2. Apply bead of Mopar
T
Gasket Maker, or equivalent,
to mating surface of rear extension housing. Keep
sealer bead width to maximum of 3/16 inch. Do not
use excessive amount of sealer as excess could
be displaced into output bearing.
3. Align and install rear extension (1) on the transfer
case (2).
4. Apply Mopar
T
Silicone Sealer to threads of rear
extension housing bolts. Then install and tighten
bolts to 16-24 N·m (12-18 ft. lbs.) torque.
INSTALLATION
1. Mount transfer case on a transmission jack.
2. Secure transfer case to jack with chains.
3. Position transfer case under vehicle.
4. Align transfer case and transmission shafts and install transfer case onto the transmission.
5. Install and tighten transfer case attaching nuts to 27-34 N·m (20-25 ft. lbs.) torque.
6. Connect the vent hose.
7. Connect the shift motor and mode sensor wiring connectors. Secure wire harness to clips on transfer case.
8. Align and connect the propeller shafts. (Refer to 3 - DIFFERENTIAL & DRIVELINE/PROPELLER SHAFT/FRONT
PROPELLER SHAFT - INSTALLATION) (Refer to 3 - DIFFERENTIAL & DRIVELINE/PROPELLER SHAFT/REAR
PROPELLER SHAFT - INSTALLATION)
9. Fill transfer case with correct fluid. (Refer to 21 - TRANSMISSION/TRANSFER CASE/FLUID - STANDARD PRO-
CEDURE)
10. Install skid plate, if equipped.
11. Remove transmission jack and support stand.
21 - 1496
TRANSFER CASE - NV244 GENII - SERVICE INFORMATION
DR/DH
12. Lower vehicle and verify transfer case shift operation.
SPECIFICATIONS
TRANSFER CASE - NV244 GENII
TORQUE SPECIFICATIONS
DESCRIPTION
N-m
Ft. Lbs.
In. Lbs.
Plug, Detent
16-24
12-18
-
Plug, Drain/Fill
20-34
15-25
-
Bolt, Extension Housing
16-24
12-18
-
Bolt, Case Half
25-28
18-21
-
Screw, Oil Pump
14-19
10-14
-
Nuts, Mounting
30-41
20-30
-
Bolts, Shift Motor and
Mode Sensor Assembly
16-24
12-18
-
DR/DH
TRANSFER CASE - NV244 GENII - SERVICE INFORMATION
21 - 1497
SPECIAL TOOLS
TRANSFER CASE - NV244 GENII
Installer, Bushing - 5066
Installer, Bearing - 6953
Cup - 8148
Installer - 8840
Installer, Seal - 8841
Handle, Universal - C-4171
Installer, Seal - D-163
Remover - L-4454
Installer, Seal - MB991168A
21 - 1498
TRANSFER CASE - NV244 GENII - SERVICE INFORMATION
DR/DH
SEAL-EXTENSION HOUSING
REMOVAL
1. Raise and support vehicle.
2. Remove rear propeller shaft. (Refer to 3 - DIFFERENTIAL & DRIVELINE/PROPELLER SHAFT/PROPELLER
SHAFT - REMOVAL)
3. Using a suitable pry tool or slide-hammer mounted screw, remove the extension housing seal.
INSTALLATION
1. Clean fluid residue from sealing surface and
inspect for defects.
2. Using Installer D-163 (2) and Handle C-4171 (1),
install seal in extension housing.
3. Install propeller shaft. (Refer to 3 - DIFFERENTIAL
& DRIVELINE/PROPELLER SHAFT/PROPELLER
SHAFT - INSTALLATION)
4. Verify proper transfer case fluid level.
5. Lower vehicle.
FLUID
STANDARD PROCEDURE - FLUID DRAIN AND REFILL
NOTE: The fill (2) and drain (3) plugs are both in
the rear case.
1. Raise vehicle.
2. Position drain pan under transfer case.
NOTE: It may be necessary to remove the exhaust
y-pipe at the exhaust manifold to properly access
the fill and drain plugs. Lowering the exhaust will
allow the plugs to be accessed for torquing during
installation. (Refer to 11 - EXHAUST SYSTEM/EX-
HAUST PIPE - REMOVAL)
3. Remove drain (3) and fill (2) plugs and drain lubri-
cant completely.
4. Install drain plug (3). Tighten plug to 20-34 N·m
(15-25 ft. lbs.).
5. Remove drain pan.
6. Fill transfer case to bottom edge of fill plug opening with Mopar
T
ATF +4, Automatic Transmission fluid.
7. Install and tighten fill plug (2) to 20-34 N·m (15-25 ft. lbs.).
8. Install the exhaust y-pipe to the exhaust manifold, if removed. (Refer to 11 - EXHAUST SYSTEM/EXHAUST
PIPE - INSTALLATION)
9. Wipe any excess fluid that may have spilled onto the exhaust.
10. Lower vehicle.
DR/DH
TRANSFER CASE - NV244 GENII - SERVICE INFORMATION
21 - 1499
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст