Dodge Ram Truck 1500-2500-3500. Manual — part 192
APS RELAY CONTROL CIRCUIT LOW (CONTINUED)
3.
ADJUSTABLE PEDALS RELAY CONTROL CIRCUIT SHORTED TO GROUND
Turn the ignition off.
Remove the FCM from the IPM.
Remove the Adjustable Pedals Relay.
Turn the ignition on.
Measure the resistance between ground and the Adjustable Pedals Relay Control circuit in the Adjustable Pedals
Relay Control circuit terminal.
Is the resistance below 100 ohms?
Yes
>> Repair the short to ground in the Adjustable Pedals Relay Control circuit.
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Replace the FCM in accordance with the Service Information
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
4.
INTERMITTENT DTC
Turn the ignition off.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Check connectors - Clean/repair as necessary.
Refer to any Technical Service Bulletins that may apply.
Were any problems found?
Yes
>> Repair as necessary.
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Test Complete.
5 - 196
BRAKES - ABS - ELECTRICAL DIAGNOSTICS
DR/DH
APS RELAY CONTROL CIRCUIT OPEN
DR/DH
BRAKES - ABS - ELECTRICAL DIAGNOSTICS
5 - 197
APS RELAY CONTROL CIRCUIT OPEN (CONTINUED)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
Ignition on.
•
Set Condition:
When the FCM detects an open on the Adjustable Pedals Relay Control circuit.
Possible Causes
INTERMITTENT DTC
ADJUSTABLE PEDAL RELAY
ADJUSTABLE PEDAL CONTROL CIRCUIT OPEN
ANTI-LOCK BRAKE MODULE
Diagnostic Test
1.
VERIFY DTC
With the DRBIII
T
, record and erase DTCs.
Turn the ignition on.
With the DRBIII
T
, read DTCs.
Does the DTC reset?
Yes
>> Go To 2
No
>> Go To 4
2.
ADJUSTABLE PEDALS RELAY OPERATION
Turn the ignition off.
Substitute the Adjustable Pedals Relay with a known good one.
Turn the ignition on.
Attempt to operate the Adjustable Pedals.
With the DRBIII
T
, read DTC.
Does the DTC reset?
Yes
>> Go To 3
No
>> Replace the Adjustable Pedals Relay.
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
5 - 198
BRAKES - ABS - ELECTRICAL DIAGNOSTICS
DR/DH
APS RELAY CONTROL CIRCUIT OPEN (CONTINUED)
3.
ADJUSTABLE PEDALS RELAY CONTROL CIRCUIT OPEN
Turn the ignition off.
Remove the FCM from the IPM.
Remove the Adjustable Pedals Relay.
Turn the ignition on.
Measure the resistance of the Adjustable Pedals Relay Control circuit between the Adjustable Pedals Relay Control
circuit terminal and the FCM connector.
Is the resistance below 100 ohms?
Yes
>> Repair the short to ground in the Adjustable Pedals Relay Control circuit.
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Replace the FCM in accordance with the Service Information
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
4.
INTERMITTENT DTC
Turn the ignition off.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Check connectors - Clean/repair as necessary.
Refer to any Technical Service Bulletins that may apply.
Were any problems found?
Yes
>> Repair as necessary.
Perform APS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES/ELECTRICAL - DIAGNOSIS AND
TESTING)
No
>> Test Complete.
DR/DH
BRAKES - ABS - ELECTRICAL DIAGNOSTICS
5 - 199
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст