Dodge Sprinter. Manual — part 415
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Passenger Door Jamb Switch connector.
Ensure the driver door is closed or the switch is disconnected.
Observe the courtesy lamps.
Did the courtesy lamps go off?
All
Yes
→ Replace the Passenger Door Jamb Switch.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
Turn the ignition off.
Disconnect the Security System Module C1 connector.
Ensure the driver and passenger doors are closed or the switches are disconnected.
Observe the courtesy lamps.
Did the courtesy lamps go off?
All
Yes
→ Replace the Security System Module in accordance with service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Front Courtesy Lamps Control circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
217
VEHICLE THEFT/SECURITY
FRONT DOOR JAMB SWITCH CIRCUIT SHORT TO GROUND —
Continued
Symptom List:
INTERNAL ERROR - SSM
TOWING INCLINATION SENSOR BEYOND LIMITS
TOWING INCLINATION SENSOR VALUE IS INVALID
TOWING INCLINATION SENSOR VALUE IS MISSING
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be INTERNAL ERROR - SSM.
When Monitored and Set Condition:
INTERNAL ERROR - SSM
When Monitored:
Whenever the battery voltage is above 10.0 volts and the Security
System Module is connected.
Set Condition:
If the internal module test fails this DTC will set.
TOWING INCLINATION SENSOR BEYOND LIMITS
When Monitored:
Whenever the battery voltage is above 10.0 volts and the Security
System Module is connected.
Set Condition:
If the internal module test fails this DTC will set.
TOWING INCLINATION SENSOR VALUE IS INVALID
When Monitored:
Whenever the battery voltage is above 10.0 volts and the Security
System Module is connected.
Set Condition:
If the internal module test fails this DTC will set.
TOWING INCLINATION SENSOR VALUE IS MISSING
When Monitored:
Whenever the battery voltage is above 10.0 volts and the Security
System Module is connected.
Set Condition:
If the internal module test fails this DTC will set.
POSSIBLE CAUSES
DTC PRESENT
SECURITY SYSTEM MODULE FAILURE
218
VEHICLE THEFT/SECURITY
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Cycle the ignition switch from ON to OFF to ON.
Wait 10 seconds.
With the DRBIII
t, read DTC’s.
Does the DRBIII
t display the same DTC?
All
Yes
→ Replace the Security System Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
219
VEHICLE THEFT/SECURITY
INTERNAL ERROR - SSM —
Continued
Symptom:
INTRUSION SENSOR 1 CIRCUIT OPEN/SHORT TO GROUND
When Monitored and Set Condition:
INTRUSION SENSOR 1 CIRCUIT OPEN/SHORT TO GROUND
When Monitored:
Whenever the battery voltage is above 10.0 volts and the Security
System Module is connected.
Set Condition:
The Security System Module detects the incorrect voltage on the Intrusion
Sensor circuit.
POSSIBLE CAUSES
DTC PRESENT
FUSE 2 IN FUSE BLOCK 3
FUSED B(+) WIRE OPEN
GROUND CIRCUIT OPEN
INTRUSION SENSOR 1 SIGNAL SHORTED
INTRUSION SENSOR 1 SIGNAL CIRCUIT OPEN
INTRUSION SENSOR INTERFACE WIRE SHORTED
INTRUSION SENSOR INTERFACE WIRE OPEN
INTRUSION SENSOR
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Remove the ignition key.
Close and lock all doors and set the Vehicle Theft Security System.
Wait 1 minute.
Disarm the Vehicle Theft System.
With the DRBIII
t, read DTC’s.
Does the DRBIII
t display the same DTC?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Check Fuse 2 in Fuse Block 3.
Is the fuse open?
All
Yes
→ Check for a short to ground and replace the fuse.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
220
VEHICLE THEFT/SECURITY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст