Dodge Sprinter. Manual — part 483
TEST
ACTION
APPLICABILITY
2
Refer to the symptom list and perform the Checking the ECM Power and Ground
test.
Were any problem found with the ECM powers and grounds?
All
Yes
→ Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
3
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Test Complete.
101
DRIVEABILITY - DIESEL
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH —
Continued
Symptom List:
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P2201-IMMOBILIZER CAN MESSAGE ERROR
P2243-NO MESSAGE RECEIVED FROM SKREEM
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P1630-IMMOBILIZER.
POSSIBLE CAUSES
CHECKING SKREEM DTC’S
OPEN CAN BUS CIRCUITS
SKREEM MODULE
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off for 10 seconds.
Turn the ignition on.
Monitor the DRB for ECM DTCs.
Did this DTC set again?
All
Yes
→ Go To 2
No
→ Go To 4
2
Turn the ignition on.
With the DRBIII
t, attempt to communicate with the SKREEM and read SKREEM
DTCs.
NOTE: If the DRB is unable to communicate with the SKREEM, refer to the
appropriate test in the Communication category
Are there any SKREEM DTC’s?
All
Yes
→ Repair SKREEM DTC’s as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Go To 3
102
DRIVEABILITY - DIESEL
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the SKREEM Module harness connector.
Disconnect the ECM harness connectors.
Measure the resistance of each CAN Bus circuit between the ECM harness connector
and the SKREEM harness connector.
Is the resistance below 10.0 ohms for each measurement?
All
Yes
→ Replace and program the SKREEM Module in accordance with
the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Repair the open CAN Bus circuit(s) between the ECM and the
SKREEM.
Perform ROAD TEST VERIFICATION - VER-2.
4
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Test Complete.
103
DRIVEABILITY - DIESEL
P1630-IMMOBILIZER —
Continued
Symptom List:
P1681-ACM CIRCUIT FAULT
P1681-ACM CIRCUIT SHORT TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P1681-ACM CIRCUIT FAULT.
POSSIBLE CAUSES
AIRBAG CONTROL MODULE
INTERMITTENT CONDITION
ACM SIGNAL CIRCUIT SHORTED TO VOLTAGE
ENGINE CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
With the DRB, check the Airbag Module for proper communication and DTCs. If
there are any ACM DTCs, repair them prior to continuing this test.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Start the engine.
With the DRB, read ECM DTCs.
Did this DTC set again?
All
Yes
→ Go To 2
No
→ Go To 4
2
Turn the ignition off.
Disconnect the ECM harness connectors.
Remove the Engine Control Relay.
Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay
connector.
Turn the ignition on.
Measure the voltage of the ACM Signal circuit.
Is the voltage below 1.0 volt?
All
Yes
→ Replace the Engine Control Module in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Go To 3
104
DRIVEABILITY - DIESEL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст