Dodge Sprinter. Manual — part 313
(4) Remove carrier plate bolts. (Fig. 27)
(5) Disengage lift arm from glass guide rail and
remove regulator assembly. (Fig. 28)
(6) Remove four rivets attaching regulator to car-
rier plate and remove regulator. (Fig. 29)
INSTALLATION
(1) Install regulator onto carrier plate and install
new rivets.
(2) Install regulator lift arm into glass guide rail
and install regulator assembly.
(3) Install carrier bolts and tighten to 10 N·m (89
in. lbs.).
(4) Remove glass support.
(5) Connect battery negative cable.
(6) Verify correct window operation.
(7) Install trim panel. (Refer to 23 - BODY/DOOR -
FRONT/TRIM PANEL - INSTALLATION)
Fig. 26 GLASS SUPPORT
1 - WOOD WEDGE (or equivalent)
2 - WINDOW GLASS
Fig. 27 MANUAL REGULATOR ASSEMBLY
1 - DOOR
2 - CARRIER PLATE BOLTS
3 - CARRIER PLATE
4 - REGULATOR ASSEMBLY
5 - SEALING STRIP
6 - REGULATOR RIVETS (4)
7 - WINDOW CRANK/TRIM RING
8 - TRIM PANEL
9 - CLIPS
10 - WINDOW FRAME MOLDING
11 - REGULATOR
Fig. 28 LIFT ARM
1 - GLASS GUIDE RAIL
2 - LIFT ARM
Fig. 29 MANUAL REGULATOR FASTENERS
1 - RIVETS (4)
2 - REGULATOR
3 - CARRIER PLATE
23 - 22
DOOR - FRONT
VA
DOORS - REAR
TABLE OF CONTENTS
page
page
CHECK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 23
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . 29
DOOR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 30
EXTERIOR HANDLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 31
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 33
INSIDE HANDLE ACTUATOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . 33
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . 34
TRIM PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . 34
CHECK
REMOVAL
(1) Open door and disengage check arm from
receiver. (Fig. 1)
(2) Remove the screws and remove the check arm.
(3) Remove the d-pillar trim, if equipped. (Refer to
23
-
BODY/INTERIOR/D-PILLAR
TRIM
-
REMOVAL)
(4) Remove the rivets and remove the receiver.
INSTALLATION
(1) Install the receiver and replace the rivets.
(2) Install d-pillar trim, if equipped. (Refer to 23 -
BODY/INTERIOR/D-PILLAR TRIM - INSTALLA-
TION)
(3) Install check arm and screws.
(4) Tighten the screws to 10 N·m (89 in. lbs.).
DOOR
REMOVAL
(1) Disconnect and isolate battery negative cable.
(2) Open door and disengage check arm from
receiver. (Fig. 2)
(3) Using a grease pencil or equivalent, mark the
outline of the door hinges on the door to aid in instal-
lation.
(4) Support door with a suitable lifting device.
(5) Remove the bolts and remove the door. (Fig.
3)
Fig. 1 DOOR CHECK
1 - RECEIVER
2 - DOOR CHECK
3 - SCREWS
VA
DOORS - REAR
23 - 23
Fig. 2 CHECK STRAP
1 - RECEIVER
2 - DOOR CHECK
Fig. 3 DOOR HINGES
1 - DOOR
2 - TORX BOLTS (2 PER HINGE)
3 - ALLEN BOLTS (1 PER HINGE)
23 - 24
DOORS - REAR
VA
DISASSEMBLY
RIGHT DOOR
(1) Remove door. (Refer to 23 - BODY/DOORS -
REAR/DOOR - REMOVAL)
(2) Remove trim panel (20) (Fig. 4). (Refer to 23 -
BODY/DOORS - REAR/TRIM PANEL - REMOVAL)
(3) Remove latch assembly (14). (Refer to 23 -
BODY/DOORS - REAR/LATCH - REMOVAL)
(4) Remove screws (21) from door handle (20).
(5) Slide door handle (20) to right and remove.
(6) Remove rivets (15) and remove closing wedge
(16).
(7) Remove bolts (2) and remove top closing wedge
(1).
(8) Remove bolts (9) and remove door check (10).
(Refer to 23 - BODY/DOORS - REAR/CHECK -
REMOVAL)
(9) Remove the bolts (3) and remove the door
hinges (4). (Refer to 23 - BODY/DOORS - REAR/
HINGE - INSTALLATION)
Fig. 4 RIGHT DOOR
1 - TOP CLOSING WEDGE
12 - DOOR LOCK LINKAGE
2 - BOLTS
13 - BOLTS (3)
3 - BOLTS (2)
14 - LATCH ASSEMBLY
4 - DOOR HINGE
15 - RIVETS (2)
5 - PANEL
16 - BOTTOM CLOSING WEDGE
6 - SCREW
17 - LOCKING ROD
7 - INNER ACTION
18 - GROMMET
8 - PANELING
19 - LOCKING KNOB
9 - BOLTS (2)
20 - EXTERIOR DOOR HANDLE
10 - DOOR CHECK
21 - SCREW
11 - THREADED PLATE
VA
DOORS - REAR
23 - 25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст