Dodge Caliber. Manual — part 1085
![](/vehicles/wlang/mes/adolos/shi.png)
ENGINE OIL AND FILTER CHANGE
WARNING: NEW OR USED ENGINE OIL CAN BE
IRRITATING TO THE SKIN. AVOID PROLONGED
OR REPEATED SKIN CONTACT WITH ENGINE OIL.
CONTAMINANTS IN USED ENGINE OIL, CAUSED
BY INTERNAL COMBUSTION, CAN BE HAZARD-
OUS TO YOUR HEALTH. THOROUGHLY WASH
EXPOSED SKIN WITH SOAP AND WATER. DO NOT
WASH SKIN WITH GASOLINE, DIESEL FUEL, THIN-
NER, OR SOLVENTS, HEALTH PROBLEMS CAN
RESULT. DO NOT POLLUTE, DISPOSE OF USED
ENGINE OIL PROPERLY. CONTACT YOUR DEALER
OR GOVERNMENT AGENCY FOR LOCATION OF
COLLECTION CENTER IN YOUR AREA.
Change engine oil at mileage and time intervals
described in the Maintenance Schedule (Refer to
LUBRICATION
&
MAINTENANCE/MAINTENANCE
SCHEDULES - DESCRIPTION).
1. Run engine until achieving normal operating temperature.
2. Position the vehicle on a level surface and turn engine off.
3. Remove oil fill cap.
4. Raise vehicle on hoist.
5. Place a suitable oil collecting container under oil pan drain plug (2).
6. Remove oil pan drain plug (2) or and allow oil to drain into collecting container. Inspect drain plug threads for
stretching or other damage. Replace drain plug and gasket if damaged.
7. Remove oil filter (1) (Refer to 9 - ENGINE/LUBRI-
CATION/OIL FILTER - REMOVAL).
PM
ENGINE 2.0L WORLD
9 - 1627
![](/vehicles/wlang/mes/adolos/cat.png)
8. Install oil pan drain plug (2). Torque drain plug to
28 N·m (20 ft. lbs.).
9. Install new oil filter (Refer to 9 - ENGINE/LUBRI-
CATION/OIL FILTER - INSTALLATION).
10. Lower vehicle and fill crankcase with specified
type and amount of engine oil (Refer to LUBRI-
CATION & MAINTENANCE/SPECIFICATIONS -
FLUID CAPACITIES) and (Refer to LUBRICA-
TION
&
MAINTENANCE/FLUID
TYPES
-
DESCRIPTION).
11. Install oil fill cap.
12. Start engine and inspect for leaks.
13. Stop engine and inspect oil level.
OIL FILTER SPECIFICATION
All engines are equipped with a high quality full-flow, disposable type oil filter. Replace oil filter with a Mopar
T
or the
equivalent.
USED ENGINE OIL DISPOSAL
Care should be exercised when disposing used engine oil after it has been drained from a vehicle engine. Refer to
the WARNING listed above.
9 - 1628
ENGINE 2.0L WORLD
PM
![](/vehicles/wlang/mes/adolos/gethod.png)
FILTER-OIL
REMOVAL
CAUTION: When servicing the oil filter avoid
deforming the filter can by installing the remove/
install tool band strap against the can to base lock
seam. The lock seam joining the can to the base is
reinforced by the base plate.
1. Using a suitable filter wrench, turn oil filter (1)
counterclockwise to remove.
INSTALLATION
1. Clean and check filter mounting surface. The sur-
face must be smooth, flat and free of debris or
pieces of gasket.
2. Lubricate new oil filter gasket.
3. Screw oil filter (1) on until the gasket contacts
base. Tighten to 21 N·m (15 ft. lbs.).
PM
ENGINE 2.0L WORLD
9 - 1629
![](/vehicles/wlang/mes/adolos/zerzwhe.png)
PAN-OIL
REMOVAL
1. Raise vehicle on hoist.
2. Drain engine oil.
3. Remove accessory drive belt splash shield.
4. Remove lower A/C compressor mounting bolt (if
equipped).
5. Remove A/C mounting bracket.
NOTE: Do not use pry points in block to remove
oil pan.
6. Remove oil pan retaining bolts.
7. Using a putty knife (1), loosen seal around oil pan
(2).
8. Remove oil pan (2).
INSTALLATION
1. Apply Mopar
T
Engine RTV GEN II at the front
cover to engine block parting lines (1).
9 - 1630
ENGINE 2.0L WORLD
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст