Dodge Caliber. Manual — part 1351
P
ASSENGER
FOLD
FLA
T
SEA
T
PM
SEATS
23 - 141
REMOVAL
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
WARNING: The Seat Weight Sensor is a sensitive,
calibrated unit and must be handled carefully. Do
not drop or handle roughly. If dropped or dam-
aged, replace with another sensor. Failure to fol-
low these instructions may result in personal
injury or death.
WARNING: The front passenger seat must be han-
dled carefully as well. When removing the seat, be
careful when setting on floor not to drop. If
dropped, the sensor may be inoperative. Failure to
follow these instructions may result in personal
injury or death.
WARNING: When the seat is on the floor, no one
should sit in the front passenger seat. This uneven force may damage the sensing ability of the seat weight
sensors. If sat on and damaged, the sensor may be inoperative. Failure to follow these instructions may
result in personal injury or death.
2. Using a trim stick C-4755 or equivalent, remove the seat belt anchor trim (3).
3. Remove the bolt (2) and separate the seat belt anchor (1).
1 - SEAT BACK CUSHION/COVER
20 - OCS STRAIN GAUGE (4)
2 - RECLINER HANDLE
21 - SEAT CUSHION STRAP BOLTS - FRONT (2) 11 N·m (8 ft. lbs.)
3 - OUTBOARD RECLINER SHIELD
22 - SEAT CUSHION STRAPS - FRONT (2)
4 - SEAT BACK FRAME
23 - SEAT CUSHION STRAP BUSHINGS - FRONT (2)
5 - HEADREST SLEEVES
24 - TRACK POSITION SENSOR
6 - HEADREST
25 - SEAT TRACK ASSEMBLY
7 - SEAT BACK TRIM PANEL
26 - SIDE SHIELD SCREWS (one per side)
8 - INBOARD RECLINER SHIELD
27 - OUTBOARD SIDE SHIELD - OUTER
9 - PUSH PIN FASTENERS (2)
28 - SEAT BELT ANCHOR TRIM
10 - SUB PANEL BASE TRIM
29 - SEAT BELT ANCHOR
11 - WIRE HARNESS
30 - SEAT BELT ANCHOR BOLT 47 N·m (35 ft. lbs.)
12 - HEATED SEAT MODULE
31 - SEAT CUSHION STRAP BUSHINGS - REAR (2)
13 - SEAT BELT BUCKLE
32 - OUTBOARD SIDE SHIELD - INNER
14 - SEAT BELT BUCKLE BOLT 45 N·m (33 ft. lbs.)
33 - INBOARD SIDE SHIELD - INNER
15 - INBOARD SIDE SHIELD - OUTER
34 - SEAT CUSHION PAN
16 - OCS MODULE
35 - RECLINER HANDLE RETAINER CLIP
17 - BACK ASSEMBLY BOLTS (4) 40 N·m (30 ft. lbs.)
36 - HEATING ELEMENT - SEAT BACK
18 - SEAT CUSHION STRAPS - REAR (2)
37 - HEATING ELEMENT - SEAT CUSHION
19 - SEAT CUSHION STRAP BOLTS - REAR (2) 11 N·m (8 ft. lbs.)
38 - SEAT CUSHION/COVER
23 - 142
SEATS
PM
4. Remove the bolts (2).
5. Tip the seat back and disconnect the electrical con-
nectors (1).
6. Remove the seat.
PM
SEATS
23 - 143
INSTALLATION
1. Before proceeding with the following repair proce-
dure, review all warnings and cautions. (Refer to
23 - BODY/SEATS - WARNING)
WARNING: The Seat Weight Sensor is a sensitive,
calibrated unit and must be handled carefully. Do
not drop or handle roughly. If dropped or dam-
aged, replace with another sensor. Failure to fol-
low these instructions may result in personal
injury or death.
WARNING: The front passenger seat must be han-
dled carefully as well. When removing the seat, be
careful when setting on floor not to drop. If
dropped, the sensor may be inoperative. Failure to
follow these instructions may result in personal
injury or death.
WARNING: When the seat is on the floor, no one
should sit in the front passenger seat. This uneven force may damage the sensing ability of the seat weight
sensors. If sat on and damaged, the sensor may be inoperative. Failure to follow these instructions may
result in personal injury or death.
2. Position the seat into the vehicle and connect the electrical connectors (1), if equipped.
3. Install the bolts (2).
a. Adjust the seat forward.
b. Tighten the rear outboard bolt to 51 N·m (38 ft.
lbs.).
c. Tighten the rear inboard bolt to 51 N·m (38 ft.
lbs.).
d. Adjust the seat rearward.
e. Tighten the front outboard bolt to 51 N·m (38 ft.
lbs.).
f. Tighten the front inboard bolt to 51 N·m (38 ft.
lbs.).
23 - 144
SEATS
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст