Dodge Durango (DN). Manual — part 303
INSTALLATION
(1) Engage the replacement bulb wire loop to the
terminal closest to the lamp base wire connector.
(2) Depress the opposite terminal inward and
engage the remaining bulb wire loop.
(3) Position the lamp lens on the lamp base and
press into place.
DOME LAMP BULB
REMOVAL
(1) Using a small flat blade, pry the left side (driv-
er’s side) of the lamp lens downward.
(2) Pull bulb from lamp.
INSTALLATION
(1) Install bulb in lamp.
(2) Position lens on lamp and snap into place.
2ND SEAT DOME/READING LAMP BULB
REMOVAL
(1) Using a small flat blade, pry the center rear-
ward edge of the dome/reading lamp lens downward
from lamp (Fig. 9).
(2) Pull bulb from socket (Fig. 10).
INSTALLATION
(1) Position bulb in lamp.
(2) Push the lamp lens up into the lamp to secure.
Fig. 8 Underhood Lamp Bulb
1 – BULB
2 – DEPRESS TERMINAL INWARD
3 – BULB WIRE LOOP
4 – LAMP BASE
Fig. 9 Lamp Lens
1 – FLAT BLADE
2 – LENS
Fig. 10 Dome/Reading Lamp Bulb
1 – LAMP LENS
2 – BULB
3 – SWITCH
DN
LAMPS
8L - 13
REMOVAL AND INSTALLATION (Continued)
OVERHEAD CONSOLE READING LAMP BULB
REMOVAL
(1) Using a small flat blade, carefully pry forward
edge of reading lamp lens downward from lamp.
(2) Disengage lamp lens from pivots on overhead
console.
(3) Rotate bulb holder and pull bulb from lamp.
INSTALLATION
(1) Position bulb in lamp and rotate to secure.
(2) Position lamp lens on overhead console. Ensure
contact tab (Fig. 11) on lamp lens is aligned with
lamp switch.
(3) Carefully press lamp lens onto pivots.
Fig. 11 Reading Lamp Lens
1 – SWITCH CONTACT TAB
2 – READING LAMP LENS
8L - 14
LAMPS
DN
REMOVAL AND INSTALLATION (Continued)
LAMP SERVICE
TABLE OF CONTENTS
page
page
DESCRIPTION AND OPERATION
LAMP SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . 15
REMOVAL AND INSTALLATION
LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LIFTGATE/CARGO LAMP . . . . . . . . . . . . . . . . . . . 17
TAIL, BRAKE, TURN SIGNAL AND BACK-UP
LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LICENSE PLATE LAMP . . . . . . . . . . . . . . . . . . . . 18
UNDERHOOD LAMP . . . . . . . . . . . . . . . . . . . . . . 18
DOME LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2ND SEAT DOME/READING LAMP . . . . . . . . . . . 19
OVERHEAD CONSOLE READING LAMP . . . . . . . 20
DESCRIPTION AND OPERATION
LAMP SYSTEMS
Each vehicle is equipped with various lamp assem-
blies. A good ground is necessary for proper lighting
operation. Grounding is provided through a separate
ground wire.
When changing lamp bulbs check the socket for
corrosion. If corrosion is present, clean it with a wire
brush and coat the inside of the socket lightly with
Mopar
t Multi-Purpose Grease or equivalent.
HEADLAMPS
DESCRIPTION
Headlamps on the Durango are modular in design.
The turn/park lamp module is incorporated into the
headlamp module. The module contains four bulbs; a
dual filament headlamp bulb, two dual filament turn/
park bulbs, and a side marker bulb.
OPERATION
Headlamps and parking lamps are controlled by
the
headlamp
switch.
The
multifunction
switch
mounted on the steering column controls the high
beam function, and the turn signal function.
HEADLAMP SWITCH
DESCRIPTION
The headlamp switch modules located on the
instrument panel. The headlamp switch controls the
parking lamps and the headlamps. A separate switch
in the module controls the interior lamps, and instru-
ment cluster illumination. This switch also contains
a rheostat for controlling the illumination level of the
instrument cluster lamps.
OPERATION
The headlamp switch has an off position, a parking
lamp position, and a headlamp on position. High
beams are controlled by the multifunction switch on
the steering column. The headlamp switch cannot be
repaired. It must be replaced. Refer to Group 8E for
removal and installation procedures, and Group 8W
for wiring.
DAYTIME RUNNING LAMP MODULE
DESCRIPTION
The Daytime Running Lights (Headlamps) System
is installed on vehicles manufactured for sale in Can-
ada only. A separate module, mounted on the cowl,
controls the DRL.
OPERATION
The headlamps are illuminated when the ignition
switch is turned to the ON position. The DRL module
receives a vehicle-moving signal from the vehicle
speed
sensor.
This
provides
a
constant
head-
lamps-on condition as long as the vehicle is moving.
The lamps are illuminated at less than 50 percent of
normal intensity.
TAIL/STOP/TURN SIGNAL/BACK–UP LAMP
DESCRIPTION
The taillamps on the Durango are mounted at the
rear of the vehicle, outboard of the rear hatch and
integrated into the lines of the vehicle. The taillamp
module contains a housing, lens, and three bulbs.
Dual filament bulb is used for tail, stop, and turn
signal operations. A separate bulb is used for back-up
illumination.
OPERATION
Tail lamp functions are controlled by the headlamp
switch. Turn signal operations are controlled by the
multifunction switch. Stop lamp functions are con-
trolled by the stoplamp switch. The back-up lamps
are controlled by the back-up lamp switch on the
transmission.
DN
LAMPS
8L - 15
REMOVAL AND INSTALLATION
HEADLAMP
REMOVAL
(1) Open hood.
(2) Remove the bolts attaching headlamp to the
inner fender panel (Fig. 1).
(3) Grasp the headlamp and firmly pull the head-
lamp to disengage it from the panel.
(4) Disengage the connector from the headlamp
bulb.
(5) Separate bulb from headlamp.
(6) Remove the bulb sockets from the front park/
turn signal/side marker lamps
(7) Separate headlamp module from vehicle.
INSTALLATION
CAUTION: Do not touch the bulb glass with fingers
or other oily surfaces. Reduced bulb life will result.
(1) Install bulb sockets for the front park/turn sig-
nal/side marker lamps
(2) Engage the connector to the headlamp bulb.
(3) Position headlamp in inner fender panel and
firmly push headlamp inward to lock into place.
(4) Install the bolts attaching headlamp to the
panel.
FOG LAMP
The fog lamps are serviced from the rearward side
of the front bumper.
REMOVAL
(1) Disengage fog lamp harness connector.
(2) Remove the bolts attaching the fog lamp to the
bumper (Fig. 2).
(3) Separate fog lamp from bumper.
INSTALLATION
(1) Position fog lamp in bumper.
(2) Install the bolts attaching the fog lamp to the
bumper.
(3) Connect fog lamp harness connector.
(4) Check for proper operation and beam align-
ment.
PARK, TURN SIGNAL AND SIDE MARKER
LAMP
REMOVAL
(1) Remove torx screw attaching park lamp to
headlamp module (Fig. 3).
(2) Pull the park and turn signal lamp outward
and separate from headlamp module.
(3) Remove park and turn signal sockets from back
of lamp (Fig. 4).
(4) Remove side marker socket from back of lamp.
(5) Separate park and turn signal lamp from vehi-
cle.
INSTALLATION
(1) Install side marker socket in back of lamp.
(2) Install park and turn signal sockets in back of
lamp.
(3) Using the guides on the bottom and side of the
headlamp module, align the park and turn signal
lamp under headlamp module.
(4) Slide the park and turn signal lamp inward
under headlamp module. Push firmly until the lamp
is seated.
Fig. 1 Headlamp
1 – FENDER
2 – SEAL
3 – INNER FENDER
Fig. 2 Fog Lamp
1 – FOG LAMP
2 – FRONT BUMPER
8L - 16
LAMPS
DN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст