Dodge Durango (DN). Manual — part 302
SPECIAL TOOLS
HEADLAMP ALIGNMENT
Headlamp Aiming Kit C-4466–A
DN
LAMPS
8L - 9
LAMP BULB SERVICE
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 10
FOG LAMP BULB. . . . . . . . . . . . . . . . . . . . . . . . . 10
PARK AND TURN SIGNAL LAMP BULBS . . . . . . . 11
FRONT SIDE MARKER LAMP BULB. . . . . . . . . . . 11
CENTER HIGH MOUNTED STOP LAMP
(CHMSL) BULB . . . . . . . . . . . . . . . . . . . . . . . . . 11
LIFTGATE/CARGO LAMP BULB . . . . . . . . . . . . . . 11
TAIL, BRAKE, TURN SIGNAL AND BACK-UP
LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
LICENSE PLATE LAMP BULB . . . . . . . . . . . . . . . 12
UNDERHOOD LAMP BULB . . . . . . . . . . . . . . . . . 12
DOME LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . 13
2ND SEAT DOME/READING LAMP BULB. . . . . . . 13
OVERHEAD CONSOLE READING LAMP BULB . . 14
REMOVAL AND INSTALLATION
HEADLAMP BULB
REMOVAL
(1) Open hood.
(2) Remove headlamp assembly. See headlamp
removal in the lamp service section.
(3) Remove the retaining ring holding bulb to
headlamp.
(4) Pull bulb socket from headlamp (Fig. 1).
(5) Grasp bulb and pull from socket.
INSTALLATION
CAUTION: Do not touch the bulb glass with fingers
or other oily surfaces. Reduced bulb life will result.
(1) Position bulb into socket and push into place.
(2) Position bulb socket in headlamp.
(3) Install retaining ring holding bulb to head-
lamp.
(4) Install headlamp assembly.
FOG LAMP BULB
REMOVAL
(1) Disengage fog lamp harness connector.
(2) Rotate bulb socket a 1/4 turn counterclockwise
and pull from lamp to separate (Fig. 2).
(3) Grasp bulb and pull from lamp.
INSTALLATION
CAUTION: Do not touch the bulb glass with fingers
or other oily surfaces. Reduced bulb life will result.
(1) Position bulb in lamp, push to seat and rotate
a 1/4 turn clockwise.
(2) Connect fog lamp harness connector.
Fig. 1 Headlamp Bulb
1 – HEADLAMP BULB SOCKET
2 – HEADLAMP
3 – BULB
4 – SIDE MARKER LAMP BULB SOCKET
Fig. 2 Fog Lamp Bulb
1 – FOG LAMP
2 – FOG LAMP BULB
8L - 10
LAMPS
DN
PARK AND TURN SIGNAL LAMP BULBS
REMOVAL
(1) Remove park and turn signal lamp.
(2) Rotate bulb socket 1/4 turn counterclockwise
and pull turn signal lamp socket from back of lamp
(Fig. 3).
(3) Pull park and turn signal lamp bulb from
socket.
INSTALLATION
(1) Install park and turn signal lamp bulb in
socket.
(2) Install park and turn signal lamp socket into
back of lamp.
(3) Install park/turn signal lamp.
FRONT SIDE MARKER LAMP BULB
REMOVAL
(1) Remove park and turn signal lamp.
(2) Remove side marker lamp socket from back of
lamp (Fig. 1).
(3) Pull side marker lamp bulb from socket.
INSTALLATION
(1) Install side marker lamp bulb in socket.
(2) Install side marker lamp socket into back of
lamp.
(3) Install park/turn signal lamp.
CENTER HIGH MOUNTED STOP LAMP
(CHMSL) BULB
REMOVAL
(1) Remove CHMSL from liftgate.
(2) Turn bulb socket 1/4 turn counterclockwise.
(3) Separate socket from lamp.
(4) Grasp bulb and pull from socket.
INSTALLATION
(1) Position bulb in socket and press into place.
(2) Position socket in lamp.
(3) Turn bulb socket 1/4 turn clockwise.
(4) Install CHMSL.
LIFTGATE/CARGO LAMP BULB
REMOVAL
(1) Remove liftgate/cargo lamp from liftgate.
(2) Using a small flatblade, pry lamp lens from
lamp.
(3) Remove bulb from lamp.
INSTALLATION
(1) Install in bulb in lamp.
(2) Install lamp lens on lamp.
(3) Install liftgate/cargo lamp in liftgate.
TAIL, BRAKE, TURN SIGNAL AND BACK-UP
LAMP BULB
REMOVAL
(1) Release liftgate latch and open liftgate.
(2) Remove screws attaching tail, brake, turn sig-
nal and back-up lamp to liftgate opening.
(3) Separate inner end of lamp from quarter panel.
(4) Disengage hook holding outer end of lamp to
quarter panel opening.
(5) Separate lamp from quarter panel.
(6) Rotate lamp socket counterclockwise one quar-
ter turn (Fig. 4).
(7) Pull socket from back of lamp.
(8) Pull bulb from socket (Fig. 5).
INSTALLATION
(1) Align key on bulb base to groove in socket and
insert bulb into socket (Fig. 5).
(2) Insert socket into back of lamp.
(3) Rotate lamp socket clockwise one quarter turn.
(4) Engage hook to hold outer end of lamp to quar-
ter panel opening.
(5) Place lamp in position on quarter panel.
(6) Install screws attaching lamp to liftgate open-
ing.
Fig. 3 Park And Turn Signal Lamp bulb
1 – SIDE MARKER LAMP BULB
2 – PARK/TURN SIGNAL LAMP BULB
DN
LAMPS
8L - 11
REMOVAL AND INSTALLATION (Continued)
LICENSE PLATE LAMP BULB
REMOVAL
(1) Remove license plate lamp from rear bumper.
(2) Remove bulb socket from lamp (Fig. 6).
(3) Pull bulb from socket.
INSTALLATION
(1) Push bulb in socket.
(2) Install bulb socket in lamp.
(3) Install license plate lamp in rear bumper.
UNDERHOOD LAMP BULB
REMOVAL
(1) Insert a small flat blade in the access slot
between the lamp base and lamp lens.
(2) Pry the lamp lens upward and remove the
lamp lens (Fig. 7).
(3) Depress the bulb terminal inward (Fig. 8) to
release the bulb.
Fig. 4 Tail, Brake, Turn Signal and Back-up Lamp
Bulb
1 – TAIL, STOP AND TURN SIGNAL LAMP
2 – SOCKET
3 – BULB
Fig. 5 Pull Bulb From Socket
1 – SOCKET
2 – BULB
Fig. 6 License Plate Lamp Bulb
1 – SOCKET
2 – BULB
3 – LICENSE PLATE LAMP
Fig. 7 Underhood Lamp Lens
1 – LAMP
2 – LAMP LENS
8L - 12
LAMPS
DN
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст