Dodge Durango (DN). Manual — part 169
LIFTGATE SCUFF PLATE
REMOVAL
(1) Remove screws attaching cargo tie downs to
liftgate scuff plate (Fig. 86).
(2) Grasp scuff plate and lift upward to disengage
spring clips.
(3) Separate scuff plate from liftgate opening.
INSTALLATION
(1) Position scuff plate in liftgate opening.
(2) Press scuff plate to engage spring clips.
(3) Install screws attaching cargo tie downs to lift-
gate scuff plate (Fig. 86).
FRONT SEAT BELT RETRACTOR
CAUTION: Inspect the condition of the shoulder
belt and lap belt. Replace any belt that is cut,
frayed, torn, or damaged in any way. Also, replace
the shoulder belt if the retractor is either damaged
or inoperative.
REMOVAL
(1) Detach the turning loop cover from the upper
anchor bolt.
(2) Remove upper anchor bolt (Fig. 87).
(3) Remove B-pillar trim.
(4) Remove the retractor anchor bolt.
(5) Disconnect retractor wire harness connector.
(6) Remove screws attaching web guide to B-pillar.
(7) Remove front seat side shield, if equipped.
(8) Remove front seat belt anchor bolt (Fig. 88).
(9) Separate retractor from vehicle.
INSTALLATION
(1) Position retractor in the vehicle.
(2) Install retractor anchor bolt. Tighten to 39 N·m
(29 ft. lbs.) torque.
(3) Connect retractor wire harness connector.
(4) Install web guide to B-pillar.
(5) Install B-pillar trim.
(6) Install upper anchor bolt. Tighten to 39 N·m
(29 ft. lbs.) torque.
Fig. 86 Liftgate Scuff Plate
1 – CARGO TIE DOWN
2 – LIFT GATE SCUFF PLATE
Fig. 87 Front Seat Belt Retractor
1 – TURNING LOOP
2 – ADJUSTER
3 – UPPER B-PILLAR TRIM
4 – B-PILLAR
5 – ANTI-RATTLE CUP
6 – ANCHOR BOLT
7 – LOWER B-PILLAR TRIM
8 – RETRACTOR
Fig. 88 Front Seat Belt Anchor
1 – ANCHOR BOLT
2 – BUCKET SEAT
23 - 56
BODY
DN
REMOVAL AND INSTALLATION (Continued)
(7) Install turning loop cover.
(8) Install front seat belt anchor bolt (Fig. 88).
Tighten to 23 N·m (17 ft. lbs.) torque.
(9) Install front seat side shield, if equipped.
FRONT SEAT BELT BUCKLE
REMOVAL
(1) If equipped, remove floor console.
(2) Remove front seats, if necessary.
(3) Remove bolt attaching buckle to seat track
(Fig. 89).
(4) Separate buckle from seat track.
INSTALLATION
(1) Position buckle on seat track.
(2) Install bolt attaching buckle to seat track.
Tighten the bolt to 23 N·m (17 ft. lbs.) torque. Buckle
should be free to partially pivot fore and aft after the
bolt is torqued.
(3) Install seats, if removed.
(4) If removed, install floor console.
2ND ROW SEAT BELT RETRACTOR
CAUTION: Inspect the condition of the shoulder
belt and lap belt. Replace any belt that is cut,
frayed, torn, or damaged in any way. Also, replace
the shoulder belt if the retractor is either damaged
or inoperative.
REMOVAL
(1) Partially remove quarter panel trim to access
fasteners.
(2) Remove bolt attaching seat belt anchor to floor
panel.
(3) Remove bolt attaching retractor to C-pillar
(Fig. 90).
(4) Separate retractor from vehicle.
INSTALLATION
(1) Position retractor in vehicle.
(2) Install bolt attaching retractor to C-pillar (Fig.
90). Tighten bolt to 39N·m (29 ft. lbs.) torque.
(3) Install bolt attaching seat belt anchor to floor
panel. Tighten bolt to 39 N·m (29 ft. lbs.) torque.
(4) Install quarter panel trim.
2ND ROW SEAT BELT BUCKLE
REMOVAL
(1) Move 2nd row seat to forward tumble position.
(2) Remove
bolts
attaching
seat
belt/buckle
anchors to floor pan (Fig. 91).
(3) Separate seat belt/buckle from vehicle.
INSTALLATION
(1) Position seat belt/buckle in vehicle.
(2) Install bolts attaching seat belt/buckle anchors
to floor pan (Fig. 91). Tighten bolts to 95 N·m (70 ft.
lbs.) torque.
(3) Move and latch 2nd row seat to seating posi-
tion.
3RD ROW SEAT BELT RETRACTOR
CAUTION: Inspect the condition of the shoulder
belt and lap belt. Replace any belt that is cut,
frayed, torn, or damaged in any way. Also, replace
the shoulder belt if the retractor is either damaged
or inoperative.
REMOVAL
(1) Remove 3rd row seat.
(2) Remove quarter panel trim.
(3) Remove screws attaching belt guide to D-pillar.
(4) Remove bolt attaching retractor to D-pillar
(Fig. 92).
(5) Separate retractor from vehicle.
INSTALLATION
(1) Position retractor on D-pillar.
(2) Install bolt attaching retractor to D-pillar (Fig.
92). Tighten bolt to 39 N·m (29 ft. lbs.) torque.
(3) Install screws attaching belt guide to D-pillar.
(4) Install quarter panel trim.
(5) Install 3rd row seat.
Fig. 89 Seat Belt Buckle
1 – ANCHOR BOLT
2 – SEAT TRACK
3 – SEAT CUSHION
4 – BUCKLE
DN
BODY
23 - 57
REMOVAL AND INSTALLATION (Continued)
Fig. 90 2nd Row Retractor
1 – ADJUSTER
2 – C-PILLAR TRIM
3 – TURNING LOOP
4 – QUARTER PANEL TRIM
5 – ANCHOR BOLT
6 – BELT ANCHOR
7 – ANTI-RATTLE CUP
8 – RETRACTOR
9 – C-PILLAR
Fig. 91 2nd Row Seat Belt/Buckle
1 – BUCKLE ANCHOR
2 – FLOOR PAN
3 – REAR SEAT (2ND SEAT)
23 - 58
BODY
DN
REMOVAL AND INSTALLATION (Continued)
3RD ROW SEAT BELT BUCKLE
REMOVAL
(1) Move 3rd row seat cushion to cargo position.
(2) Remove bolt attaching seat belt buckle to floor
pan.
(3) Separate seat belt buckle from vehicle (Fig. 93).
INSTALLATION
(1) Position seat belt buckle in vehicle (Fig. 93).
(2) Install bolt attaching seat belt buckle to floor
pan. Tighten bolt to 39 N·m (29 ft. lbs.) torque.
(3) Move 3rd row seat cushion to seating position.
BUCKET SEAT
REMOVAL
If vehicle is equipped with center seat/console,
remove seats and console as one assembly.
(1) If equipped, remove side shield and disengage
power seat switch connector.
(2) Move seat to full forward position.
(3) Remove rear screws attaching trim cover to
seat track (Fig. 94).
(4) Remove rear bolts attaching rear seat track to
floor pan.
(5) Move seat to full rearward position.
(6) Remove front screws attaching trim cover to
seat track (Fig. 94).
(7) Remove front bolts attaching front seat track to
floor pan.
NOTE: Do not actuate recliner or track adjuster
once bolts are removed.
(8) Tilt setback forward and lift seat out through
door.
INSTALLATION
(1) Position seat in vehicle.
(2) Install bolts attaching front seat track to floor
pan. Tighten bolts in sequence:
(a) Driver’s seat:
(I) Front outboard
(II) Front inboard
(b) Passenger’s seat:
Fig. 92 3rd Row Seat Belt Retractor
1 – D-PILLAR
2 – RETRACTOR
3 – ANTI-RATTLE CUP
4 – BUCKLE
5 – ANCHOR BOLT
6 – STUD
7 – BELT ANCHOR
8 – TURNING LOOP
9 – D-PILLAR TRIM
DN
BODY
23 - 59
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст