Dodge Durango (DN). Manual — part 170
(I) Front inboard
(II) Front outboard
(c) Bucket seat with center seat (40/20/40)
(I) Driver’s front outboard
Fig. 93 3rd Row Seat Belt Buckle
1 – 3RD ROW SEAT BELT BUCKLE
2 – FLOOR PAN
Fig. 94 Bucket Seat
1 – COVER
2 – COVER
3 – COVER
4 – COVER (POWER SEAT)
5 – COVER
6 – COVER (POWER SEAT)
7 – U-NUT
8 – FLOOR PAN
9 – U-NUT
10 – BUCKET SEAT
23 - 60
BODY
DN
REMOVAL AND INSTALLATION (Continued)
(II) Passenger’s front inboard
(III) Driver’s front inboard
(IV) Passenger’s front outboard
Tighten bolts attaching front seat track to floor
pan to 28 N·m (20 ft. lbs.) torque.
(4) Install front screws attaching trim cover to seat
track.
(5) Move seat to full forward position.
(6) Install bolts attaching rear inboard seat track
to floor pan. Tighten to 40 N·m (30 ft. lbs.) torque.
(7) Install bolts attaching rear outboard seat track
to floor pan. Tighten to 28 N·m (20 ft. lbs.) torque.
(8) Install rear screws attaching trim cover to seat
track.
(9) If equipped, engage power seat switch connec-
tor and install side shield.
2ND ROW SEAT
The 2nd row seat is removed as a complete assem-
bly.
REMOVAL
(1) Move seat to the forward tumble position.
(2) Remove outboard bolts attaching seat to the
floor pan (Fig. 95).
(3) Remove
inboard
bolts
attaching
seat
belt
buckle anchors and seat to floor pan (Fig. 96).
(4) Remove seat from the vehicle.
INSTALLATION
(1) Position seat in the vehicle.
(2) Install inboard bolts attaching seat belt buckle
anchors and seat to floor pan (Fig. 96). Tighten bolts
to 95 N·m (70 ft. lbs.) torque.
(3) Install outboard bolts attaching seat to the
floor pan (Fig. 95). Tighten bolts to 27 N·m (20 ft.
lbs.) torque.
(4) Move and latch seat in the seating position.
3RD ROW SEAT
REMOVAL
(1) Move 2nd row seat to forward tumble position.
(2) Lift 3rd row seat cushion upward and forward
to floor cargo position.
(3) Remove bolts attaching 3rd row seat to floor
pan (Fig. 97).
(4) Remove seat from vehicle.
Fig. 95 2nd Row Seat
1 – REAR SEAT
2 – FLOOR PAN
Fig. 96 2nd Row Seat Belt Anchors
1 – BUCKLE ANCHOR
2 – FLOOR PAN
3 – REAR SEAT (2ND SEAT)
DN
BODY
23 - 61
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Position seat in vehicle.
(2) Install bolts attaching 3rd row seat to floor pan
(Fig. 97) in the following sequence:
(a) Right front bolt
(b) Left front bolt
(c) Left rear bolt
(d) Right rear bolt
(3) Tighten bolts to 27 N·m (20 ft. lbs.) torque.
(4) Move and latch 3rd row seat cushion to seating
position.
(5) Move and latch 2nd row seat to seating posi-
tion.
FLOOR CONSOLE
REMOVAL
(1) Using a small flat blade, remove forward and
rearward cup holder inserts.
(2) Remove screws attaching floor console to floor
pan (Fig. 98).
(3) Disconnect
wire
harness
for
rear
HEVAC
blower, if equipped.
(4) Lift
console
upward
and
disengage
from
HEVAC duct, if equipped.
(5) Separate console from vehicle.
INSTALLATION
(1) Position console in vehicle.
(2) Engage HEVAC duct to console, if equipped.
(3) Connect wire harness for rear HEVAC blower,
if equipped.
Fig. 98 Floor Console
1 – CUP HOLDER INSERT
2 – CUP HOLDER INSERT
3 – FLOOR CONSOLE
4 – HEVAC DUCT
5 – FLOOR PAN
6 – SHIFT BEZEL
Fig. 97 3rd Row Seat
1 – BENCH SEAT
2 – FLOOR PAN
23 - 62
BODY
DN
REMOVAL AND INSTALLATION (Continued)
(4) Install screws attaching floor console to floor
pan (Fig. 98).
(5) Install forward and rearward cup holder inserts.
FLOOR CARPET
FRONT CARPET REMOVAL
(1) Remove floor console, if equipped.
(2) Remove front seats.
(3) Remove center console, if equipped.
(4) Remove 2nd row seats.
(5) Remove 3rd row seats, if equipped.
(6) Remove front and rear door sill trim.
(7) Remove lower left and right cowl trim.
(8) Remove left and right B-pillar trim.
(9) Remove left and right quarter panel trim.
(10) Loosen gas pedal bracket.
(11) Remove rear fresh air vent.
(12) Route wiring through carpet.
(13) Remove carpet from vehicle (Fig. 99).
FRONT CARPET INSTALLATION
(1) Position carpet in vehicle and align all holes.
(2) Route all wire harnesses through openings in
carpet.
(3) Install front and rear door sill trim.
(4) Install quarter panel trim.
(5) Install B-pillar trim.
(6) Install lower cowl trim.
(7) Tighten gas pedal bracket.
(8) Install 3rd row seats, if equipped.
(9) Install 2nd row seats.
(10) Install rear fresh air vent.
(11) Install center console, if equipped.
(12) Install front seats.
(13) Install floor console, if equipped.
REAR CARPET REMOVAL
(1) Remove 3rd row seats, if equipped.
(2) Remove 3rd row seat belt/buckles, if equipped.
(3) Remove left and right quarter panel trim.
(4) Remove liftgate scuff plate.
(5) Remove screws attaching cargo compartment
lid hinge to floor.
(6) Remove carpet from vehicle (Fig. 99).
REAR CARPET INSTALLATION
(1) Position carpet in vehicle and align all holes.
(2) Install screws attaching cargo compartment lid
hinge to floor.
(3) Install liftgate scuff plate.
(4) Install quarter panel trim.
(5) Install 3rd row seat belt/buckles, if equipped.
(6) Install 3rd row seats, if equipped.
Fig. 99 Floor Carpet
1 – FRONT CARPET
2 – REAR CARPET
3 – STORAGE COMPARTMENT LINER
4 – PLASTIC PUSH-IN NUT
DN
BODY
23 - 63
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст