Dodge Neon / Neon SRT-4. Manual — part 491
Symptom:
MODULE NOT CONFIGURED FOR RKE
When Monitored and Set Condition:
MODULE NOT CONFIGURED FOR RKE
When Monitored:
When the ignition is in the run position during Remote Keyless Entry
transmitter programming.
Set Condition:
When the operator attempts to program a transmitter and the RKE
module is not configured for RKE.
POSSIBLE CAUSES
MODULE NOT CONFIGURED FOR RKE
TEST
ACTION
APPLICABILITY
1
The RKE transmitter will not program because the module is not configured for RKE.
View repair.
All
Repair
Using the DRBIII
t, configure the module for Remote Keyless
Entry.
Perform BODY VERIFICATION TEST - VER 1.
186
POWER DOOR LOCKS/RKE
Symptom:
NO AIRBAG MESSAGES RECEIVED
When Monitored and Set Condition:
NO AIRBAG MESSAGES RECEIVED
When Monitored:
With the ignition on or in the run position.
Set Condition:
The RKE Module does not receive any airbag messages for 12 seconds.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE ACM
RKE MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, attempt to communicate with the ACM.
Was the DRB able to I/D or communicate with the ACM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRB, erase DTC’s.
Turn the ignition on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
187
POWER DOOR LOCKS/RKE
Symptom:
NO PCM MESSAGES RECEIVED
When Monitored and Set Condition:
NO PCM MESSAGES RECEIVED
When Monitored:
With the ignition on or in the run position.
Set Condition:
The RKE Module does not receive any PCM messages for 12 seconds.
POSSIBLE CAUSES
NO PCM MESSAGES RECEIVED
ATTEMPT TO COMMUNICATE WITH THE PCM
PCI BUS CIRCUIT OPEN
POWERTRAIN CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then J1850 MODULE SCAN.
Is the PCM present on the bus?
All
Yes
→ With the DRB, erase DTCs. Cycle the ignition switch and check
for DTCs. If DTC resets, replace the RKE Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition on.
With the DRB, attempt to communicate with the PCM.
Was the DRB able to communicate with the PCM?
All
Yes
→ Go To 3
No
→ Refer to the communication category and perform the appropriate
symptom.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the RKE Module harness connector.
Measure the resistance of the PCI Bus circuit between the RKE Module connector
and the PCM connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Powertrain Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the PCI Bus circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
188
POWER DOOR LOCKS/RKE
Symptom:
NO SKIM MESSAGES RECEIVED
When Monitored and Set Condition:
NO SKIM MESSAGES RECEIVED
When Monitored:
With the ignition on or in the run position.
Set Condition:
The RKE Module does not receive any SKIM messages for 12 seconds.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE SKIM
RKE MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, attempt to communicate with the SKIM.
Was the DRB able to I/D or communicate with the SKIM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRB, erase DTC’s.
Turn the ignition on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
189
POWER DOOR LOCKS/RKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст