Dodge Neon / Neon SRT-4. Manual — part 100
LAMPS/LIGHTING - INTERIOR
TABLE OF CONTENTS
page
page
LAMPS/LIGHTING - INTERIOR
. . . . . . . . . . . . . . . . . . . . . 28
CUP HOLDER LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
DOME LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
GLOVE BOX LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
GLOVE BOX LAMP SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
READING LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
SHIFT BEZEL (PRNDL) ILLUMINATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 30
VANITY LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 30
LAMPS/LIGHTING - INTERIOR
SPECIFICATIONS
INTERIOR LAMPS
CAUTION: Do not use bulbs other than those listed
in the chart below. Damage to lamp can result.
BULB APPLICATION CHART
LAMP
BULB
ABS INDICATOR
LED
AIRBAG INDICATOR
LED
BRAKE SYSTEM
WARNING INDICATOR
LED
CLIMATE CONTROLS
LED
CONSOLE GEAR
SELECTOR W/AUTO
PC 194
DOME LAMP
T579
FRONT FOG LAMP
INDICATOR
LED
GLOVE COMPARTMENT
T194
HIGH BEAM LAMP
INDICATOR
PC194
IGNITION LOCK
161
INSTRUMENT CLUSTER
ILLUMINATION
PC194
LOW FUEL INDICATOR
LED
LAMP
BULB
LOW OIL PRESSURE
INDICATOR
LED
REAR CARGO
T906
SEAT BELT INDICATOR
LED
SECURITY ALARM
INDICATOR
LED
SHIFT BEZEL (PRNDL)
LAMP
T37
MALFUNCTION
INDICATOR LIGHT
LED
TRAC OFF INDICATOR
LED
TURN SIGNAL
INDICATOR
PC194
UNDERHOOD
105
VISOR VANITY
6501966
VOLTAGE INDICATOR
LED
All the interior bulbs are brass or glass wedge
base. Aluminum base bulbs are not approved and
should not be used for replacement.
8L - 28
LAMPS/LIGHTING - INTERIOR
PL/SRT-4
CUP HOLDER LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Insert a small screwdriver into notch by lens
and gently pry out unit.
(3) Slide back rear cover to expose bulb.
(4) Remove bulb.
INSTALLATION
(1) Install bulb.
(2) Insert bulb into cover.
(3) Align bulb holder with slots on instrument
panel and firmly snap into place.
(4) Connect battery negative cable.
DOME LAMP
REMOVAL
LAMP
(1) Disconnect and isolate the battery negative
cable.
(2) Insert a trim stick between the dome lamp
bezel and dome lamp lens.
(3) Carefully pull down on lamp lens to remove
lamp from headliner.
(4) Disconnect wire connector.
(5) Remove lamp.
BULB
(1) Disconnect and isolate the battery negative
cable.
(2) Insert a trim stick between the dome lamp
bezel and dome lamp lens.
(3) Carefully swing down one side of the lamp
lens.
(4) Remove bulb from lamp socket.
INSTALLATION
LAMP
(1) Place lamp into position.
(2) Connect wire connector.
(3) Install dome lamp and lens.
(4) Connect the battery negative cable.
BULB
(1) Push bulb in socket and snap into place.
(2) Position lens on lamp and snap into place.
(3) Connect the battery negative cable.
GLOVE BOX LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Open glove box door.
(3) Pull downward on lamp/switch assembly to dis-
engage tabs from instrument panel.
(4) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Place lamp/switch assembly into position.
(3) Push lamp/switch assembly to lock tabs.
(4) Check lamp operation, and close glove door.
(5) Connect the battery negative cable.
GLOVE BOX LAMP SWITCH
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Open glove box door.
(3) Pull downward on lamp/switch assembly to dis-
engage tabs from instrument panel.
(4) Pull bulb from socket.
(5) Disconnect wire connector from lamp and
remove glove box lamp/switch.
INSTALLATION
(1) Push bulb into socket.
(2) Place lamp/switch assembly into position.
(3) Connect wire connector to the lamp/switch.
(4) Push lamp/switch assembly to lock tabs.
(5) Check lamp operation, and close glove box door.
(6) Connect the battery negative cable.
READING LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Using a small thin blade tool, pry at the center
of the lens nearest the mirror to remove lens.
(3) Remove cartridge lamp.
INSTALLATION
(1) Install lens by setting lens into position and
applying pressure until it is locked into position.
(2) Connect the battery negative cable.
PL/SRT-4
LAMPS/LIGHTING - INTERIOR
8L - 29
SHIFT BEZEL (PRNDL)
ILLUMINATION
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove floor console.
(3) Remove wiring and socket from shift bezel
(PRNDL).
(4) Remove bulb from socket.
INSTALLATION
(1) Push bulb in socket and snap into place.
(2) Install floor console.
(3) Connect the battery negative cable.
VANITY LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Lower visor.
(3) Insert a small flat bladed tool between the
lamp lens and lamp.
(4) Carefully pry lens outward.
(5) Remove bulb from socket.
INSTALLATION
(1) Position bulb in socket and snap into place.
(2) Position lens on lamp and snap into place.
(3) Connect the battery negative cable.
8L - 30
LAMPS/LIGHTING - INTERIOR
PL/SRT-4
MESSAGE SYSTEMS
TABLE OF CONTENTS
page
page
COMPASS/TEMPERATURE MIRROR
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DIAGNOSIS AND TESTING - COMPASS/
. . . . . . . . . . . . . . . . 1
CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . 2
VARIATION ADJUSTMENT . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
AMBIENT TEMPERATURE SENSOR
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DIAGNOSIS AND TESTING - AMBIENT
. . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . 4
COMPASS/TEMPERATURE
MIRROR
DESCRIPTION
COMPASS / TEMPERATURE MIRROR
The Compass/Temperature Mirror consists of an
electronic control module with a vacuum fluorescent
display (VFD) screen (Fig. 1), two map/reading lamps
and function switches. The electronic module dis-
plays the outside temperature and one of eight com-
pass headings to indicate the direction the vehicle is
facing. The compass/temperature mirror transmits
and receives data on the PCI Data Bus Circuitry.
COMPASS
The compass is capable of self-calibrating. Refer to
the procedures later in this section of the service
manual. The compass is located within the mirror
module and can not be serviced separately.
THERMOMETER
The Compass/Temperature Mirror displays the out-
side temperature using data from the NGC engine
controller on the PCI databus. Engine temperature
can increase the displayed temperature.
OPERATION
The optional compass/temperature mirror incorpo-
rates 2 reading lamp buttons, which also function as
STEP
and
ZONE/CALIBRATION
buttons.
The
desired function is obtained by pressing and holding
a button depressed for a specific time period. The
STEP button provides the selections between English
and Metric. The Zone/Cal. button is used to change
the compass zone or calibrate the compass.
The STEP button (right reading lamp button) oper-
ates a momentary contact switch, which is used to
toggle through the following four modes:
• Turn the right reading lamp on and off.
• To select degrees Fahrenheit or Celsius for the
temperature display (Press and Hold for 5 to 10 sec-
onds).
• To turn display off (Press and Hold for 10 to 15
seconds).
The ZONE/CALIBRATION button (left reading
lamp button) operates a momentary contact switch,
which is used to toggle through the following two
modes:
• Turn the left reading lamp on and off.
• To actuate compass Zone/Calibration modes
(Press and Hold for 5 to 10 seconds).
DIAGNOSIS AND TESTING - COMPASS/
TEMPERATURE MIRROR
If the Compass/Temperature mirror lights up and
functions, however the accuracy of the information
displayed is in question or certain displays are not
Fig. 1 Compass/Temperature Mirror
PL/SRT-4
MESSAGE SYSTEMS
8M - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст