Dodge Neon / Neon SRT-4. Manual — part 99
REMOVAL
(1) Disconnect and isolate the battery negative
cable (Fig. 21).
(2) Remove both upper and lower steering column
shrouds. (Refer to 19 - STEERING/COLUMN/UPPER
SHROUD - REMOVAL).
(3) Disconnect both posi-lock harness connectors at
the rear of the multi-function switch (Fig. 22) and
(Fig. 23).
(4) Remove multi-function switch mounting screws
(Fig. 22) and (Fig. 23).
(5) The combination flasher must be transferred to
new multi-function switch if replacing (Fig. 22).
(6) The windshield wiper/washer switch must be
transferred to the new multi-function switch. (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WIPER/
WASHER SWITCH - REMOVAL).
INSTALLATION
(1) The windshield wiper/washer switch must be
transferred to the new multi-function switch. (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WIPER/
WASHER SWITCH - INSTALLATION).
(2) The combination flasher must be transferred to
new multi-function switch if replacing.
(3) Install the multi-function switch mounting
screws. Tighten multi-function switch to column
retaining screws to 3 N·m (27 in. lbs.) torque.
(4) Connect both posi-lock harness connectors at
the rear of the multi-function switch.
(5) Instal both upper and lower steering column
shrouds. (Refer to 19 - STEERING/COLUMN/UPPER
SHROUD - INSTALLATION).
(6) Connect the battery negative cable.
Fig. 21 DISCONNECT AND ISOLATE BATTERY
NEGATIVE CABLE
1 - NEGATIVE CABLE
2 - NEGATIVE BATTERY POST
Fig. 22 MULTI-FUNCTION SWITCH MOUNTING
1 - MULTI-FUNCTION SWITCH CONNECTOR
2 - HAZARD/WARNING SWITCH
3 - WINDSHIELD WIPER/WASHER SWITCH CONNECTOR
4 - MOUNTING SCREWS
5 - COMBINATION FLASHER
8L - 24
LAMPS/LIGHTING - EXTERIOR
PL/SRT-4
MULTI-FUNCTION SWITCH (Continued)
Fig. 23 MULTI-FUNCTION SWITCH - REMOVE/INSTALL
1 - MULTI-FUNCTION SWITCH CONNECTORS
3 - MULTI-FUNCTION SWITCH
2 - RETAINING SCREWS
PL/SRT-4
LAMPS/LIGHTING - EXTERIOR
8L - 25
MULTI-FUNCTION SWITCH (Continued)
REAR FOG LAMP
DESCRIPTION
Therear fog lamps can be found in the rear of the
vehicle, integrated into the rear tail lamp assembly.
Rear fog lamps utilize a red lens and clear bulb.
OPERATION
The rear fog lamps are turned ON and OFF with
the rear fog lamp switch. (Refer to 8 - ELECTRICAL/
LAMPS/LIGHTING
-
EXTERIOR/FOG
LAMP
SWITCH - OPERATION). Refer to Wiring Diagrams
for a complete system schematic.
DIAGNOSIS AND TESTING - REAR FOG LAMP
- EXPORT
Refer to Wiring Diagrams for a complete system
schematic.
(1) Remove the rear fog lamp bulb and check for
burned out condition. Replace bulb if necessary.
(2) If bulb appears OK, reinstall the bulb in its
socket and rotate the ignition switch to the “ON”
position. Turn the rear fog lamp “ON” and check for
lamp operation. If lamp is still inoperative proceed to
Step 3
(3) Remove lamp bulb and check for proper power
(12v) and ground connections in lamp socket. If
power and/or ground connections are not present,
trace wire until open or short is found. Refer to Wir-
ing Diagrams for a complete system schematic.
REMOVAL
REAR FOG LAMP UNIT
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the appropriate two rear fog lamp
retaining screws.
(3) Pull the fog lamp assembly from the rear
bumper fascia.
(4) Rotate and pull the lamp socket from the lamp
housing.
(5) Remove lamp assembly from vehicle.
REAR FOG LAMP BULB
(1) Remove the fog lamp unit from the rear
bumper fascia (Refer to 8 - ELECTRICAL/LAMPS/
LIGHTING - EXTERIOR/FOG LAMP - REMOVAL).
(2) Pull bulb out of socket and replace bulb (Fig.
24).
INSTALLATION
REAR FOG LAMP UNIT
(1) Install the lamp socket into the lamp housing.
(2) Install the lamp assembly into rear bumper
fascia.
(3) Install the appropriate two rear fog lamp
retaining screws.
(4) Connect the battery negative cable.
REAR FOG LAMP BULB
(1) Push in bulb (Fig. 24).
(2) Install the fog lamp unit into the rear bumper
fascia (Refer to 8 - ELECTRICAL/LAMPS/LIGHT-
ING - EXTERIOR/FOG LAMP - INSTALLATION).
Fig. 24 REAR FOG LAMP SOCKET
1 - REAR FOG LAMP
2 - REAR FOG LAMP SOCKET
8L - 26
LAMPS/LIGHTING - EXTERIOR
PL/SRT-4
TAIL LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Move trunk lining as necessary from rear clo-
sure panel to gain access to back of tail lamp.
(3) Remove bulb socket from tail lamp through
openings in rear closure panel (Fig. 25).
(4) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Install bulb socket into tail lamp through open-
ings in rear closure panel.
(3) Reposition trunk lining to rear closure panel.
(4) Connect the battery negative cable.
TAIL LAMP UNIT
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Move trunk lining as necessary from rear clo-
sure panel to gain access to back of tail lamp.
(3) Remove nuts attaching tail lamp to the rear
closure panel.
(4) Disconnect the wiring connectors from the bulb
sockets.
(5) Remove lamp housing from vehicle.
INSTALLATION
(1) Pull wiring and connectors through opening in
rear closure panel and install wiring connectors into
bulb sockets.
(2) Place lamp assembly into position.
(3) Install lamp assembly nuts.
(4) Reposition trunk lining.
(5) Connect the battery negative cable.
(6) Verify vehicle and system operation.
TRUNK LAMP UNIT
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Insert a trim stick or small flat blade between
the lamp lens and rear shelf reinforcement panel.
(3) Pry the lamp lens downward.
(4) Disconnect wire connector.
(5) Remove lamp from vehicle.
INSTALLATION
(1) Place lamp into position.
(2) Connect wire connector.
(3) Install lamp lens.
(4) Connect battery negative cable.
Fig. 25 TAIL AND STOP LAMP BULB
1 - REAR CLOSURE PANEL
2 - TAIL LAMP
3 - SOCKET
4 - BULB
PL/SRT-4
LAMPS/LIGHTING - EXTERIOR
8L - 27
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст