Dodge Neon / Neon SRT-4. Manual — part 373
NOTE: Tag all valve/spring assemblies for reassem-
bly identification.
(13) Remove dual retainer plate using Tool 6301
(Fig. 348).
(14) Remove regulator valve spring retainer (Fig.
349).
(15) Remove remaining retainers as shown in (Fig.
350).
(16) Remove valves and springs as shown in (Fig.
351).
Fig. 348 Remove Dual Retainer Plate using Tool
6301
1 - TOOL 6301
2 - RETAINER
Fig. 349 Remove Regulator Valve Spring Retainer
using Tool 6302
1 - TOOL 6302
2 - RETAINER
Fig. 350 Valve Retainer Location
1 - RETAINER
2 - RETAINER
21 - 276
40TE AUTOMATIC TRANSAXLE
PL/SRT-4
VALVE BODY (Continued)
NOTE: Refer to Valve Body Cleaning and Inspection
for cleaning procedures.
ASSEMBLY
NOTE: If valve body assembly is reconditioned, the
PCM/TCM Quick Learn Procedure must be per-
formed. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL
MODULES/TRANSMISSION
CONTROL
MODULE - STANDARD PROCEDURE)
(1) Install valves and springs as shown in (Fig.
351).
(2) Install regulator valve spring retainer (Fig.
352).
(3) Install dual retainer plate using Tool 6301 (Fig.
353).
Fig. 351 Springs and Valves Location
1 - VALVE BODY
5 - MANUAL VALVE
2 - T/C REGULATOR VALVE
6 - CONVERTER CLUTCH SWITCH VALVE
3 - L/R SWITCH VALVE
7 - SOLENOID SWITCH VALVE
4 - CONVERTER CLUTCH CONTROL VALVE
8 - REGULATOR VALVE
Fig. 352 Install Regulator Valve Spring Retainer
using Tool 6302
1 - TOOL 6302
2 - RETAINER
PL/SRT-4
40TE AUTOMATIC TRANSAXLE
21 - 277
VALVE BODY (Continued)
(4) Verify that all retainers are installed as shown
in (Fig. 354). Retainers should be flush or below
valve body surface.
(5) Install check balls into position as shown in
(Fig. 355). If necessary, secure them with petrolatum
or transmission assembly gel for assembly ease.
Fig. 354 Valve Retainer Location
1 - RETAINER
2 - RETAINER
Fig. 355 Ball Check Location
1 - (#4) BALL CHECK LOCATION
2 - (#2) BALL CHECK LOCATION
3 - RETAINER
4 - (#3) BALL CHECK LOCATION
5 - LOW/REVERSE SWITCH VALVE
6 - T/C LIMIT VALVE
Fig. 353 Install Dual Retainer Plate using Tool 6301
1 - TOOL 6301
2 - RETAINER
21 - 278
40TE AUTOMATIC TRANSAXLE
PL/SRT-4
VALVE BODY (Continued)
(6) Install thermal valve into transfer plate (Fig.
356).
(7) Install separator plate to valve body (Fig. 357).
(8) Install the overdrive clutch (#5) check valve to
separator plate (Fig. 358)
(9) Install oil screen to separator plate (Fig. 359).
(10) Install transfer plate to valve body and sepa-
rator plate. Make sure oil screen and #5 check valve
do not bind (Fig. 360).
Fig. 356 Install Thermal Valve
1 - THERMAL VALVE
Fig. 357 Install Separator Plate
1 - SEPARATOR PLATE
2 - VALVE BODY
Fig. 358 Install Overdrive Clutch (#5) Check Valve
1 - OVERDRIVE CLUTCH (#5) CHECK VALVE
Fig. 359 Install Oil Screen
1 - OIL SCREEN
PL/SRT-4
40TE AUTOMATIC TRANSAXLE
21 - 279
VALVE BODY (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст