Dodge Neon / Neon SRT-4. Manual — part 392
INSTRUMENT PANEL
TABLE OF CONTENTS
page
page
CLUSTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
. . . . . . . . . . . . . . . . . . . . . . . . . 52
ACCESSORY SWITCH BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
. . . . . . . . . . . . . . . . . . . . . . . . . 53
GLOVE BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
. . . . . . . . . . . . . . . . . . . . . . . . . 53
INSTRUMENT PANEL ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . 53
. . . . . . . . . . . . . . . . . . . . . . 56
. . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . 59
INSTRUMENT PANEL CENTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
. . . . . . . . . . . . . . . . . . . . . . . . . 60
INSTRUMENT PANEL END COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
. . . . . . . . . . . . . . . . . . . . . . . . . 61
STORAGE BIN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
. . . . . . . . . . . . . . . . . . . . . . . . . 61
INSTRUMENT PANEL TOP COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
. . . . . . . . . . . . . . . . . . . . . . . . . 61
STEERING COLUMN OPENING COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
. . . . . . . . . . . . . . . . . . . . . . . . . 61
CLUSTER BEZEL
REMOVAL
(1) Remove instrument panel top cover. Refer to
Body,
Instrument
Panel,
Instrument
Panel
Top
Cover, Removal.
(2) Using a trim stick (special tool #C-4755) or
equivalent, gently pry up on the cluster bezel and
remove from vehicle.
INSTALLATION
(1) Place the cluster bezel into position and firmly
snap into place.
(2) Install the instrument panel top cover. Refer to
Body,
Instrument
Panel,
Instrument
Panel
Top
Cover, Installation.
ACCESSORY SWITCH BEZEL
REMOVAL
(1) Disconnect and isolate the battery negative
cable (Fig. 1).
(2) Remove the instrument panel center bezel.
Refer to Body, Instrument Panel, Instrument Panel
Center Bezel Removal.
(3) Remove four screws retaining accessory switch
bezel.
(4) Disconnect the harness connectors to the fol-
lowing:
• Rear Window Defogger Switch (if equipped)
• Cigar Lighter/Power Outlet
The accessory switches are not serviced separately,
but the cigar lighter/power outlet is and must be
transferred to the new bezel. Refer to Electrical,
Fig. 1 BATTERY NEGATIVE CABLE REMOVE/
INSTALL
1 - NEGATIVE CABLE
2 - NEGATIVE BATTERY POST
23 - 52
INSTRUMENT PANEL
PL/SRT-4
Power
Distribution,
Cigar
Lighter/Power
Outlet
Removal and Installation.
INSTALLATION
The accessory switches are not serviced separately,
but the cigar lighter/power outlet is and must be
transferred to the new bezel. Refer to Electrical,
Power
Distribution,
Cigar
Lighter/Power
Outlet
Removal and Installation.
(1) Connect the harness connectors to the follow-
ing:
• Cigar Lighter/Power Outlet
• Rear Window Defogger Switch (if equipped)
(2) Install the four screws retaining the accessory
switch bezel.
(3) Install the instrument panel center bezel. Refer
to Body, Instrument Panel, Instrument Panel Center
Bezel, Installation.
(4) Connect the battery negative cable (Fig. 1).
GLOVE BOX
REMOVAL
(1) Remove three glove box door hinge screws.
(2) Open glove box and remove assembly from
vehicle.
(3) Remove the latch by gently prying the retainer
clip out of its slot.
(4) Remove nine screws retaining glove box door to
bin assembly.
(5) Remove glove box door from bin and remove.
(6) Remove dampers by gently stretching them
over the end of their pins.
INSTALLATION
(1) Assemble glove box door and bin.
(2) Install the nine screws retaining glove box door
to bin assembly.
(3) Install the latch using retainer clip.
(4) Install glove box dampers over end of pins.
(5) Place glove box into instrument panel opening.
(6) Close glove box door and install the three glove
box door hinge screws.
INSTRUMENT PANEL
ASSEMBLY
REMOVAL
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Push seats back to their full back position.
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on left and right A-pillar
trim moldings and remove.
(4) Remove the instrument panel top cover. (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL TOP COVER - REMOVAL)
(5) Gently pull up on cluster bezel and remove
from vehicle.
(6) Remove two screws. Then gently pull rearward
on left lower instrument panel cover and remove
from vehicle.
CAUTION: Lock the steering wheel in the straight
ahead position. This will prevent clock spring dam-
age when the steering wheel rotates freely.
(7) Remove steering column. (Refer to 19 - STEER-
ING/COLUMN - REMOVAL)
(8) Remove left and right instrument panel end
covers.
(9) Remove left and right cowl side panels.
(10) Remove floor console. (Refer to 23 - BODY/IN-
TERIOR/FLOOR CONSOLE - REMOVAL)
(11) Depress the sides of the Data Link Connector
(DLC) and remove from instrument panel reinforce-
ment.
(12) Remove two center support mounting bolts.
(13) Remove left and right A-pillar mounting bolts,
two on each side.
(14) Disconnect right side antenna connector.
(15) Remove left and right A-pillar door harness
connectors (Fig. 2).
PL/SRT-4
INSTRUMENT PANEL
23 - 53
ACCESSORY SWITCH BEZEL (Continued)
(16) Disconnect two harness connectors to HVAC
at right top instrument panel (Fig. 3).
(17) Disconnect one left side harness connector at
top left of instrument panel for vanity and rear view
mirrors.
(18) Pull off the HVAC control head knobs.
(19) Remove both A/C outlet barrels.
(20) Remove two screws retaining the top front of
the center bezel.
(21) Using a trim stick or equivalent, gently pry
out on the instrument panel center bezel and remove.
(22) Remove the two retaining screws to the HVAC
control head.
(23) Disconnect the one instrument panel wire
harness connector.
(24) Disconnect the one vacuum harness connector.
(25) Pull HVAC control head out of instrument
panel, twist 90° and push back through the opening
(Fig. 4). Do not disconnect the control cables.
(26) Disconnect the center console wiring:
• Airbag Control Module (ACM)
• Parking Brake Warning Lamp Switch
• Transmission Range Indicator Lamp
• Shift Interlock Cable (ATX)
(27) With help from an assistant, remove two bolts
on top of the brake pedal support bracket. Pull rear-
ward on instrument panel assembly and remove from
vehicle.
(28) Remove center A/C duct from the instrument
panel (Fig. 15).
If replacing instrument panel, transfer parts (Fig.
5) as necessary.
Fig. 2 A-PILLAR DOOR HARNESS CONNECTOR
1 - INSTRUMENT PANEL HARNESS CONNECTOR
2 - DOOR CHECK STRAP
3 - DOOR HARNESS CONNECTOR
Fig. 3 INSTRUMENT PANEL TO HVAC HARNESS
CONNECTORS
1 - HVAC HARNESS CONNECTORS
Fig. 4 HVAC CONTROL HEAD
1 - HVAC CONTROL HEAD
2 - RADIO
3 - HVAC CONTROL HEAD HARNESS CONNECTOR
23 - 54
INSTRUMENT PANEL
PL/SRT-4
INSTRUMENT PANEL ASSEMBLY (Continued)
Fig. 5 INSTRUMENT PANEL ASSEMBLY
1 - INSTRUMENT PANEL ASSEMBLY
9 - BEZEL INSTRUMENT PANEL, CENTER
2 - TOP COVER ASSEMBLY
10 - BIN, LOWER STORAGE
3 - MODULE, PASSENGER SIDE AIRBAG
11 - STEERING COLUMN COVER ASSEMBLY
4 - END CAP, RIGHT
12 - CLUSTER BEZEL
5 - DEMISTER GRILLE, RIGHT
13 - LOUVER, AIR OUTLET, LEFT
6 - LOUVER, AIR OUTLET, RIGHT
14 - END CAP, LEFT
7 - DOOR, GLOVE BOX
15 - DEMISTER GRILLE, LEFT
8 - LOUVER, AIR OUTLET, CENTER
PL/SRT-4
INSTRUMENT PANEL
23 - 55
INSTRUMENT PANEL ASSEMBLY (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст