Dodge Neon / Neon SRT-4. Manual — part 391
LATCH
REMOVAL
Domestic
(1) Remove the upper fasteners securing the grille
to the upper radiator closure panel. (Fig. 4)
(2) Using a socket and extension, remove the nuts
attaching hood latch to radiator closure panel. (Fig.
5)
(3) Carefully pull the grille out from the radiator
closure and remove the hood latch assembly.
(4) Disengage remote release cable from latch.
International
(1) Release hood latch and open hood.
(2) Support hood on prop rod.
(3) Remove grille.
(4) Remove nuts attaching hood latch to radiator
closure panel (Fig. 5).
(5) Remove hood latch from closure panel.
(6) Disengage remote release cable from latch.
INSTALLATION
Domestic
(1) Engage remote release cable into latch.
(2) Carefully pull back the grille and place hood
latch onto radiator closure panel.
(3) Install the nuts and tighten to 15 N·m (11 ft.
lbs.).
(4) Install the upper fasteners securing the grille
to the upper radiator closure panel.
International
(1) Engage remote release cable into latch.
(2) Place hood latch onto radiator closure panel.
(3) Install nuts attaching latch to closure panel
and tighten to 15 N·m (11 ft. lbs.).
(4) Install grille.
(5) Close hood and verify alignment of hood and
that latch is securely engaged.
Fig. 4 FRONT FASCIA - DOMESTIC
1 - PUSH PIN FASTENER(S)
2 - ATTACHING SCREW(S)
3 - GRILLE
4 - EMBLEM NUT
5 - FRONT BUMPER FOAM
6 - FASCIA TO FENDER NUT
7 - EMBLEM
8 - SURROUND LOWER GRILLE
9 - SURROUND UPPER GRILLE
10 - FRONT FASCIA
23 - 48
HOOD
PL/SRT-4
LATCH RELEASE CABLE
REMOVAL
(1) Unlatch hood and open
(2) Disconnect remote hood release cable from
hood latch (Refer to 23 - BODY/HOOD/LATCH -
REMOVAL).
(3) Release any remote hood cable attachments
and free cable (Fig. 6).
(4) Remove left front cowl trim panel (Refer to 23 -
BODY/INTERIOR/SIDE COWL TRIM - REMOVAL).
(5) Remove screws attaching hood release handle
to cowl panel and release cable from clip (Fig. 7).
(6) Disconnect rubber grommet from dash panel
behind instrument panel.
(7) Pull release cable through hole in dash panel.
(8) Remove cable and handle from vehicle.
INSTALLATION
(1) From inside of vehicle feed remote release
cable through hole in dash panel (Fig. 7)
(2) Connect rubber grommet into dash panel.
(3) Install screws attaching hood release handle to
cowl panel.
(4) Install left front cowl trim panel (Refer to 23 -
BODY/INTERIOR/SIDE COWL TRIM - INSTALLA-
TION).
(5) Connect any remote cable attachments (Fig. 6).
(6) Connect remote hood release cable to hood
latch (Refer to 23 - BODY/HOOD/LATCH - INSTAL-
LATION).
(7) Close hood and verify operation.
(8) Check remote hood release cable for proper
operation.
Fig. 5 HOOD LATCH
1 - HOOD LATCH RELEASE CABLE
2 - HOOD PROP ROD
3 - HOOD SECURITY ALARM
4 - HOOD LATCH
PL/SRT-4
HOOD
23 - 49
LATCH (Continued)
Fig. 6 HOOD REMOTE RELEASE CABLE
1 - HOOD LATCH RELEASE CABLE ASSEMBLY
2 - DASH PANEL
Fig. 7 HOOD RELEASE CABLE - INSIDE
1 - HOOD LATCH RELEASE ASSEMBLY
2 - CLIP
3 - HOOD LATCH RELEASE HANDLE - ATTACHING BOLT(S)
23 - 50
HOOD
PL/SRT-4
LATCH RELEASE CABLE (Continued)
LATCH STRIKER
REMOVAL
(1) Release hood latch and open hood.
(2) Remove bolts attaching striker to inside of
hood.
(3) Remove hood latch striker from vehicle.
INSTALLATION
(1) Position hood latch striker on vehicle.
(2) Install bolts attaching hood latch striker to
hood. Tighten bolts to 13.5 N·m (10 ft. lbs.) torque.
(3) Align hood latch striker to engage smoothly
into hood latch.
(4) Verify hood operation and alignment. Adjust as
necessary.
(5) Tighten attaching bolts to 13.5 N·m (10 ft. lbs.)
torque.
SILENCER PAD
REMOVAL
(1) Release hood latch and open hood.
(2) Disconnect hood lamp wire connector and
remove hood lamp (Fig. 8).
(3) Remove fasteners attaching hood silencer to
hood.
(4) Remove hood silencer from vehicle.
INSTALLATION
(1) Place hood silencer in position on vehicle.
(2) Install fastener attaching hood silencer to hood.
(3) Install hood lamp and connect wire connector.
(4) Close hood.
ADJUSTMENT BUMPER
REMOVAL
(1) Release hood latch and open hood.
(2) Rotate hood adjuster bumper counterclockwise.
(3) Remove hood adjuster bumper from headlamp
reinforcement.
HOOD AIR SCOOP BEZEL
REMOVAL
(1) Release hood latch and open hood.
(2) Remove nuts attaching hood air scoop bezel to
hood (Fig. 9).
(3) Remove hood air scoop bezel from vehicle.
INSTALLATION
(1) Place into position hood air scoop bezel.
(2) Install nuts attaching hood air scoop bezel to
hood (Fig. 9).
(3) Close hood.
Fig. 8 SILENCER PAD
1 - HOOD
2 - HOOD SILENCER
Fig. 9 HOOD AIR SCOOP BEZEL
1 - HOOD AIR SCOOP BEEZEL
2 - HOOD ASSEMBLY
3 - ATTACHING NUT(S)
PL/SRT-4
HOOD
23 - 51
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст