Dodge Neon / Neon SRT-4. Manual — part 493
TEST
ACTION
APPLICABILITY
8
Disconnect the Remote Keyless Entry module connector.
Measure the resistance of the Door Lock Relay Output circuit in the RKE module
connector to ground.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Door Lock Relay Output wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 9
9
Turn ignition off.
Disconnect the Remote Keyless Entry module connector.
Measure the resistance of the Door Unlock Relay Output circuit in the RKE module
connector to ground.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Door Unlock Relay Output wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 10
10
Disconnect the Remote Keyless Entry module connector.
Measure the resistance between the Driver Door Unlock Relay Output circuit and the
Door Lock Relay Output circuit in the RKE module connector..
Is the resistance below 3.5 ohms?
All
Yes
→ Repair the Driver Door Unlock Relay Output circuit for a short to
the Door Lock Relay Output circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 11
11
Disconnect the Remote Keyless Entry module connector.
Measure the resistance between the Door Unlock Relay Output circuit and the Door
Lock Driver Relay Output in the RKE module connector..
Is the resistance below 1.5 ohms?
All
Yes
→ Repair the Door Unlock Relay Output circuit for a short to the
Door Lock Relay Output circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 12
12
If there are no possible causes remaining, view repair.
All
Repair
Replace the Remote Keyless Entry Module and replace the fuse.
Perform BODY VERIFICATION TEST - VER 1.
13
Disconnect the RKE Module connector.
Using a test light, test both sides of Fuse #14 to ensure the fuse is Okay and that the
12.0 volt supply is not open.
Measure the Voltage of the Fused B(+) circuit (cavity #3) in the RKE Module
connector.
Is the voltage above 10.0 volts?
All
Yes
→ Go To 14
No
→ Repair the open Fused B(+) wire from the RKE Module connector
to the fuse.
Perform BODY VERIFICATION TEST - VER 1.
194
POWER DOOR LOCKS/RKE
*ALL DOOR LOCKS INOPERATIVE —
Continued
TEST
ACTION
APPLICABILITY
14
Turn ignition off.
Disconnect the RKE Module connector.
Measure the resistance of the ground circuit (cavity #8) in the RKE Module
connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 15
No
→ Repair the open ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
15
Disconnect the Remote Keyless Entry module connector.
Measure the resistance between the Driver Door Unlock Relay Output circuit and the
Door Lock Relay Output circuit in the RKE module connector..
Is the resistance LESS than 17.0 ohms?
All
Yes
→ Go To 16
No
→ Repair the open Door Lock Relay Output circuit.
Perform BODY VERIFICATION TEST - VER 1.
16
If there are no possible causes remaining, view repair.
All
Repair
Replace the Remote Keyless Entry Module (relays open).
Perform BODY VERIFICATION TEST - VER 1.
195
POWER DOOR LOCKS/RKE
*ALL DOOR LOCKS INOPERATIVE —
Continued
Symptom:
*ALL DOORS EXCEPT DRIVER FAIL TO LOCK AND UNLOCK
POSSIBLE CAUSES
RKE MODULE - OPEN DOOR UNLOCK RELAY OUTPUT
DOOR UNLOCK RELAY OUTPUT WIRE OPEN
DOOR LOCK RELAY OUTPUT WIRE OPEN
OPEN MOTORS
TEST
ACTION
APPLICABILITY
1
Disconnect the Remote Keyless Entry module connector.
Lower the passenger door window.
Connect a jumper wire between the Door Lock Relay Output ckt and the Ground ckt
in the RKE module connector.
Connect a jumper wire to the Door Unlock Relay Output ckt and momentarily touch
it to the Fused B(+) ckt and observe the passenger door locks.
Reverse the jumper wires to drive the motors in the opposite direction.
Did the passenger doors Lock and Unlock?
All
Yes
→ Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Remove the passenger door inner trim panel to gain access to the door lock motor
connector.
Disconnect the Passenger Door Lock Motor/Ajar Switch connector.
Disconnect the Remote Keyless Entry Module connector.
Measure the resistance of the Door Unlock Relay Output circuit between the RKE
module connector and the Door Lock Motor/Ajar Switch connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 3
No
→ Repair the Door Unlock Relay Output circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Remove the passenger door inner trim panel to gain access to the door lock motor
connector.
Disconnect the Passenger Door Lock Motor/Ajar Switch connector.
Disconnect the Remote Keyless Entry Module connector.
Measure the resistance of the Door Lock Relay Output circuit between the RKE
module connector and the Door Lock Motor/Ajar Switch connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Door Lock Relay Output circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Door Lock Motors as necessary.
Perform BODY VERIFICATION TEST - VER 1.
196
POWER DOOR LOCKS/RKE
Symptom:
*ALL DOORS EXCEPT DRIVER FAIL TO UNLOCK
POSSIBLE CAUSES
DOOR UNLOCK RELAY OUTPUT CIRCUIT SHORT TO GROUND
REMOTE KEYLESS ENTRY MODULE - UNLOCK RELAY
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Disconnect the Remote Keyless Entry module connector.
Measure the resistance between ground and the Door Unlock Relay Output circuit.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Door Unlock Relay Output circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
197
POWER DOOR LOCKS/RKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст