Dodge Neon / Neon SRT-4. Manual — part 382
LUBRICANT USAGE
ENGINE OIL
• Door Hinges – Hinge Pin and Pivot Contact
Areas
• Hood Hinges – Pivot Points
• Liftgate Hinges
MOPAR
T
SPRAY WHITE LUBE OR EQUIVALENT
• Door Check Straps
• Liftgate Latches
• Liftgate Prop Pivots
• Ash Receiver
• Fuel Filler Door Remote Control Latch Mecha-
nism
• Parking Brake Mechanism
• Sliding Seat Tracks
• Liftgate Latch
MOPAR
T
Multipurpose GREASE OR EQUIVALENT
• All Other Hood Mechanisms
MOPAR
T
LOCK CYLINDER LUBRICANT OR
EQUIVALENT
• Door Lock Cylinders
• Liftgate Lock Cylinder
SPECIAL TOOLS
BODY
INDEX
DESCRIPTION
FIGURE
STICK, TRIM C 4755
16
REMOVER, MOLDINGS C-4829
17
PLIERS, HEADLINER CLIP 6967
18
Fig. 16 STICK, TRIM C 4755
Fig. 17 REMOVER, MOLDINGS C-4829
Fig. 18 PLIERS, HEADLINER CLIP 6967
23 - 12
BODY
PL/SRT-4
BODY (Continued)
DECKLID/HATCH/LIFTGATE/TAILGATE
TABLE OF CONTENTS
page
page
COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . 13
DECKLID
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . 13
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . 14
LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
LIFT SPRING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 16
EMERGENCY RELEASE CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 16
COVER
REMOVAL
(1) Remove fasteners attaching decklid cover to
vehicle (Fig. 1).
(2) Remove decklid cover from vehicle.
INSTALLATION
(1) Position cover on decklid over the striker.
(2) Install push in fasteners.
(3) Seat the lower edges of the carpet and smooth
out.
(4) Close decklid.
DECKLID
REMOVAL
(1) Open decklid.
(2) Mark bolt locations on inside of decklid to aid
installation.
(3) Disengage clips attaching wire harness and
decklid release cable to decklid.
(4) Disconnect wire connector and release cable
from decklid latch.
(5) Remove bolts attaching top of hinge to decklid
(Fig. 2).
(6) With aid from a helper, remove bolts holding
bottom of hinge to decklid.
(7) Remove decklid from vehicle.
INSTALLATION
(1) Place decklid in position on vehicle.
(2) With aid from a helper, install bolts attaching
bottom of hinge to decklid.
(3) Install bolts attaching top of hinge to decklid.
(4) Align decklid to achieve equal spacing on all
sides and flush across gaps.
(5) Verify decklid operation and sealing.
(6) Connect wire connector and release cable on
latch.
(7) Install clips attaching wire harness and cable
to decklid.
Fig. 1 Decklid Trim Panel
1 - DECKLID COVER
PL/SRT-4
DECKLID/HATCH/LIFTGATE/TAILGATE
23 - 13
LATCH
REMOVAL
(1) Open decklid.
(2) Remove bolts attaching decklid latch to decklid
(Fig. 3).
(3) Remove attaching latch from decklid.
(4) Disconnect remote decklid latch release cable
form decklid latch.
(5) Disconnect decklid ajar switch connector from
latch.
(6) Remove latch from vehicle.
INSTALLATION
(1) Place decklid latch into position (Fig. 3).
(2) Connect remote decklid latch wire connector to
decklid latch.
Fig. 3 DECKLID LATCH ASSEMBLY
1 - DECKLID
2 - POWER DECKLID
3 - RETAINER CLIP(S)
4 - DECKLID SECURITY ALARM SWITCH
5 - LOCK CYLINDER
6 - GASKET
7 - DECKLID LAMP SWITCH CONNECTOR
8 - EMERGENCY DECKLID RELEASE HANDLE
9 - POWER DECKLID LATCH
10 - GROUND WIRE AND ATTACHING SCREW
Fig. 2 Decklid
1 - DECKLID
2 - DECKLID HINGE
3 - DECKLID SPRING
23 - 14
DECKLID/HATCH/LIFTGATE/TAILGATE
PL/SRT-4
DECKLID (Continued)
(3) Connect decklid ajar and lamp switch connec-
tor to latch.
(4) Install bolts attaching decklid latch to decklid
lid.
(5) Check decklid latch for proper alignment.
(6) Close decklid.
LATCH STRIKER
REMOVAL
(1) Release decklid latch and open decklid.
(2) Remove push in fasteners attaching decklid lin-
ing to tail panel.
(3) Remove trunk lining from tail panel.
(4) Remove bolts attaching decklid latch striker to
tail panel (Fig. 4).
(5) Remove striker from vehicle.
INSTALLATION
(1) Install striker in vehicle.
(2) Install trunk lining from tail panel.
(3) Install push in fasteners attaching decklid lin-
ing to tail panel.
(4) Close decklid.
LIFT SPRING
REMOVAL
WARNING: USE EYE AND HAND PROTECTION
WHEN REMOVING SPRINGS, PERSONAL INJURY
MAY RESULT.
(1) Release and open decklid.
(2) Support decklid on a suitable prop device.
(3) Using a common pliers, disengage spring from
rearward notch or hole under decklid opening side
trough (Fig. 5).
(4) Disengage spring from decklid hinge.
INSTALLATION
(1) Engage spring to decklid hinge.
(2) Using a common pliers, connect spring to the
rearward notch or hole under decklid opening side
trough (Fig. 5). Without spoiler connect the spring
into the hole. With spoiler connect spring to the
notch.
(3) Position spring with the damper at the of the
spring with only 3 coils showing.
(4) Remove decklid support device.
(5) Close decklid.
Fig. 4 Decklid Latch Striker
1 - DECKLID LATCH STRIKER
PL/SRT-4
DECKLID/HATCH/LIFTGATE/TAILGATE
23 - 15
LATCH (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст