Dodge Neon / Neon SRT-4. Manual — part 383
LOCK CYLINDER
REMOVAL
(1) Remove decklid latch.
(2) Remove clip attaching decklid lock cylinder to
decklid.
(3) Pull lock cylinder from decklid (Fig. 2).
INSTALLATION
(1) Place lock cylinder into position.
(2) Install clip attaching decklid lock cylinder to
decklid.
(3) Install decklid latch.
EMERGENCY RELEASE CABLE
REMOVAL
(1) Remove the decklid cover. (Refer to 23 - BODY/
DECKLID/HATCH/LIFTGATE/TAILGATE/COVER
-
REMOVAL)
(2) Unclip cable and handle assembly (Fig. 6).
INSTALLATION
(1) Attach emergency release cable clip to the latch
stud.
(2) Install the decklid cover. (Refer to 23 - BODY/
DECKLID/HATCH/LIFTGATE/TAILGATE/COVER
-
INSTALLATION)
Fig. 5 DECKLID HINGE LIFT SPRING
1 - UPPER HOLE WITH AND WITHOUT SPOILER
2 - FORWARD HOLE WITHOUT SPOILER
3 - REARWARD NOTCH WITH SPOILER
4 - SPRING DAMPER
5 - DECKLID HINGE SPRING
Fig. 6 EMERGENCY RELEASE CABLE - TYPICAL
1 - Release Cable Clip
2 - Decklid Latch
23 - 16
DECKLID/HATCH/LIFTGATE/TAILGATE
PL/SRT-4
LIFT SPRING (Continued)
DOOR - FRONT
TABLE OF CONTENTS
page
page
APPLIQUE
REMOVAL - FRONT AND REAR DOORS
DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INSTALLATION - LOWER FRONT DOOR
CHECK STRAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 19
DOOR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . 20
EXTERIOR HANDLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
FRONT DOOR HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . 23
LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 23
LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . 24
FRONT VERTICAL GUIDE BAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
TRIM PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
WATERDAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 26
WINDOW CRANK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 27
APPLIQUE
REMOVAL
REMOVAL - FRONT AND REAR DOORS
(1) Remove the screws.
(2) Remove screws attaching applique to door (Fig.
1).
REMOVAL - LOWER FRONT DOOR
(1) Mark reference points before removing lower
front door applique (Fig. 2).
(2) If necessary, use a heat gun gently apply heat
in a circular motion to loosen the adhesive bond.
(3) Using a nonmetallic prying device, such as a
plastic or wood trim stick gently pry up at corner of
the applique. Pull applique from front door painted
surface.
(4) Remove adhesive tape residue from painted
surface of vehicle. Use a 3M Scotch-Brite™ Molding
Adhesive and Stripe Removal Disc, or equivalent, to
clean adhesive residue from painted surfaces. These
products are available from automotive paint suppli-
ers. Refer to instructions supplied with the specific
product for proper usage.
INSTALLATION
INSTALLATION - FRONT AND REAR DOORS
(1) Place applique into position on door (Fig. 1).
(2) Install the screws attaching door applique.
INSTALLATION - LOWER FRONT DOOR
(1) If applique is to be reused (Fig. 2);
(a) Remove tape residue from applique.
(b) Clean back of applique with Mopar
t Super
Kleen, or equivalent.
(c) Wipe applique dry with lint free cloth.
(d) Apply a single coat of Mopar
t TPO Molding
Prep to tape side of molding and allow to dry thor-
oughly.
(e) Apply new body side molding (double sided)
tape to back of applique.
PL/SRT-4
DOOR - FRONT
23 - 17
(2) Clean front door surface with Mopar
t Super
Kleen, or equivalent. Wipe surface dry with lint free
cloth.
(3) Remove protective cover from tape on back of
applique.
(4) Apply molding to front door from front to rear.
(5) Using a roller tool, roll applique onto front door
panel with enough force to assure adhesion. Do not
apply excessive force, or damage to body panels may
result.
CHECK STRAP
REMOVAL
(1) Remove door trim panel and water dam.
(2) Remove bolt attaching check strap to hinge pil-
lar.
(3) Remove door speaker.
(4) Remove glass run.
(5) Remove bolts attaching check strap to door end
frame (Fig. 3).
(6) Remove check strap from vehicle.
INSTALLATION
NOTE: Do not grease check strap.
(1) Position door check on vehicle and install bolts
attaching strap to door end frame.
Fig. 1 FRONT AND REAR DOOR APPLIQUE
1 - SCREWS (3 PER APPLIQUE)
2 - SNAP IN SPRING NUTS (3 PER APPLIQUE)
3 - FRONT DOOR APPLIQUE
4 - REAR ROOD APPLIQUE
Fig. 2 LOWER FRONT DOOR APPLIQUE
1 - FRONT DOOR
2 - REMOVING ADHESIVE COVER FROM DOUBLE SIDED TAPE
3 - FRONT DOOR APPLIQUE
23 - 18
DOOR - FRONT
PL/SRT-4
APPLIQUE (Continued)
(2) Install glass run.
(3) Install door speaker, if so equipped.
(4) Install bolt attaching door check strap to hinge
pillar.
(5) Install door trim panel and water dam.
DOOR
REMOVAL
NOTE: The retaining clips used on the door hinge
pins are not to be reused. Verify availability prior to
proceeding.
(1) Open and support door on a suitable lifting
device.
(2) Disconnect wire connector at hinge pillar, if
necessary.
(3) Remove bolts attaching door check strap to
hinge pillar.
(4) Remove bolts attaching lower hinge to door.
(5) Remove bolts attaching upper hinge to door.
(Fig. 4).
(6) Remove door from vehicle.
INSTALLATION
(1) Apply Mopar
t Multi-purpose Grease to inside
of door hinge bushings.
(2) Position door to the hinges on vehicle.
(3) Install bolt into hinge top hole on the right side
or bottom hole left side (smallest hole).
(4) Install bolt into hinge bottom hole on the right
side or top hole left side (slotted hole).
(5) Install bolts attaching door check strap to
hinge pillar.
(6) Connect wire connector at hinge pillar, if nec-
essary.
Fig. 3 Front Door Check Strap
1 - FRONT DOOR GLASS RUN WEATHERSTRIP
2 - FRONT DOOR
3 - B-PILLAR
4 - SPACER
5 - DOOR LATCH STRIKER
6 - WINDOW REGULATOR HANDLE
7 - SPACER
8 - DOOR TRIM PANEL
9 - WINDOW REGULATOR
10 - DOOR CHECK STRAP
11 - FRONT DOOR GLASS RUN BRACKET WEATHER
PL/SRT-4
DOOR - FRONT
23 - 19
CHECK STRAP (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст