Dodge Neon / Neon SRT-4. Manual — part 497
TEST
ACTION
APPLICABILITY
4
Turn ignition off.
Remove the appropriate inner door trim panel to gain access to the Door Lock Motor
connector.
Disconnect the Door Lock Motor connector.
Disconnect the Remote Keyless Entry module connector.
Measure the resistance of the Door Unlock Relay Output wire to ground.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Door Unlock Relay Output wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn ignition off.
Remove the appropriate inner door trim panel to gain access to the Door Lock Motor
connector.
Disconnect the Door Lock Motor connector.
Disconnect the Remote Keyless Entry module connector.
Measure the resistance between the Door Unlock Relay Output circuit and the Door
Lock Relay Output circuit
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Door Unlock Relay Output wire for a short to the Door
Lock Relay Output wire.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Turn ignition off.
Remove the appropriate inner door trim panel to gain access to the Door Lock Motor
connector.
Disconnect the Door Lock Motor connector.
Disconnect the Remote Keyless Entry module connector.
Measure the resistance of the Door Lock Relay Output wire to ground.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Door Lock Relay Output wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
210
POWER DOOR LOCKS/RKE
*ONE PASSENGER DOOR FAILS TO LOCK & UNLOCK —
Continued
Symptom:
*RKE INOPERATIVE
POSSIBLE CAUSES
TEST TRANSMITTER WITH TESTER
RKE TRANSMITTER NOT PROGRAMMED
TEST RKE TRANSMITTER
RKE TRANSMITTER - INOPERATIVE
RKE MODULE
RKE MODULE - RECEIVER INOPERABLE
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure the RKE module is configured for RKE and the M1 (IOD) fuse
is installed.
Note: Ensure the voltage of each battery is greater than 3.0 volts before
proceeding.
Do you have access to the Miller Tool
99001 RF DETECTOR9? ?
All
Yes
→ Go To 2
No
→ Go To 4
2
Using the 9001 RF Detector, follow the instructions on the back of the tester and test
the transmitter several times.
Does the signal strength measure
9STRONG9?
All
Yes
→ Go To 3
No
→ Replace the transmitter.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition on
Place transmission in the Park position.
Ensure Vehicle Theft Security System (if equipped) is in Disarm Mode.
With the DRBIII
t, select Theft Alarm, VTSS, MISCELLANEOUS, then PROGRAM
RKE. Follow the instructions on the screen.
Exit PROGRAM RKE.
Activate the Door Locks using the RKE Transmitter.
Did the door locks respond properly to the RKE transmitter commands?
All
Yes
→ Repair complete.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Remote Keyless Entry Module and reprogram all
transmitters used with this vehicle.
Perform BODY VERIFICATION TEST - VER 1.
211
POWER DOOR LOCKS/RKE
TEST
ACTION
APPLICABILITY
4
Using the DRBIII select Theft Alarm, VTSS, MISCELLANEOUS then RKE FOB &
Module Test. Follow the instructions on the DRBIII screen.
Try the Door Locks using the original Transmitter.
Did the Door Locks respond properly to the Transmitter commands ?
All
Yes
→ Using the DRBIII, program the transmitter and recheck the
system. If okay, program all Transmitters that will be used with
this vehicle.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Secure a known good Transmitter from another PL or PT vehicle.
Using the DRBIII select BODY, Theft Alarm, VTSS, MISCELLANEOUS then RKE
FOB & Module Test. Follow the instructions on the DRBIII screen.
Try the Door Locks using the Transmitter.
Did the Door Locks respond properly to the Transmitter commands ?
All
Yes
→ Replace the original Transmitter. Program all Transmitters that
will be used with this Vehicle.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
212
POWER DOOR LOCKS/RKE
*RKE INOPERATIVE —
Continued
Symptom:
HOOD AJAR SWITCH MISSING (EXPORT ONLY)
When Monitored and Set Condition:
HOOD AJAR SWITCH MISSING (EXPORT ONLY)
When Monitored:
With the ignition on during configuration of the Remote Keyless Entry
Module.
Set Condition:
If the Hood Ajar Switch RKE Module input is NOT grounded while the
module is being configured for VTSS, this code will set.
POSSIBLE CAUSES
MODULE CONFIGURATION TEST
HOOD AJAR SWITCH OPERATIONAL TEST
OPEN GROUND CIRCUIT
HOOD AJAR SWITCH SENSE CIRCUIT OPEN
HOOD AJAR SWITCH
RKE MODULE - HOOD AJAR
TEST
ACTION
APPLICABILITY
1
Was the hood open during module configuration?
All
Yes
→ Go To 2
No
→ Open the hood and attempt to reconfigure the RKE module.
2
Open the hood.
With the DRBIII
t select: VEHICLE THEFT, VTSS, INPUT/OUTPUT.
Read the HOOD AJAR SW state.
Does the DRBIII
t show CLOSED?
All
Yes
→ Replace the Remote Keyless Entry Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Go To 3
3
Disconnect the Hood Ajar Switch connector.
Measure the resistance of the Ground circuit in the Hood Ajar connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Ground circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.
213
VEHICLE THEFT/SECURITY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст