Dodge Dakota (R1). Manual — part 10
TEST
ACTION
APPLICABILITY
4
NOTE: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
Note: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
37
AIRBAG
DRIVER SQUIB CIRCUIT SHORT - ACTIVE —
Continued
Symptom:
DRIVER SQUIB SHORT TO BATTERY - ACTIVE
When Monitored and Set Condition:
DRIVER SQUIB SHORT TO BATTERY - ACTIVE
When Monitored:
When the ignition is on, the ACM monitors the voltage of the Driver
Squib circuits.
Set Condition:
The ACM has detected voltage on the Driver Squib circuits.
POSSIBLE CAUSES
DRIVER AIRBAG MODULE SHORT TO BATTERY
CLOCKSPRING, DRIVER AIRBAG SHORT TO BATTERY
DRIVER AIRBAG LINE 1 SHORT TO BATTERY
DRIVER AIRBAG LINE 2 SHORT TO BATTERY
ACM, DRIVER AIRBAG SHORT TO BATTERY
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 brown cable and jumper harness to the
Driver Airbag connector.
Turn Ignition On and then reconnect the Battery.
With the DRBIII
t, read the active codes.
Does the DRB show DRIVER SQUIB SHORT TO BATTERY?
All
Yes
→
No
→
Replace the Driver Airbag Module.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
38
AIRBAG
TEST
ACTION
APPLICABILITY
2
NOTE: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8443 Clockspring cable and jumper harness to
the Clockspring connector.
Turn Ignition On and then reconnect the Battery.
With the DRBIII
t, read active DTCs.
Does the DRB show DRIVER SQUIB SHORT TO BATTERY ?
All
Yes
→
No
→
Replace the Clockspring.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
3
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Clockspring connector.
Disconnect the ACM connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 ACM Adaptor to the Airbag Control
Module connector.
Turn Ignition On and then reconnect the Battery.
Measure the voltage of the Driver Airbag Line 1 circuit between the Clockspring
connector and ground.
Is the voltage above 0.5 volts on Driver Airbag Line 1 circuit?
All
Yes
→
Repair Driver Airbag Line 1 circuit short to battery voltage.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
39
AIRBAG
DRIVER SQUIB SHORT TO BATTERY - ACTIVE —
Continued
TEST
ACTION
APPLICABILITY
4
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Clockspring connector.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 ACM Adaptor to the Airbag Control
Module connector.
Turn Ignition On and then reconnect the Battery.
Measure the voltage of the Driver Airbag Line 2 circuit between the Clockspring
connector and ground.
Is the voltage above 0.5 volts
All
Yes
→
Repair Driver Airbag Line 2 circuit short to battery voltage.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
5
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
40
AIRBAG
DRIVER SQUIB SHORT TO BATTERY - ACTIVE —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст