Dodge Dakota (R1). Manual — part 9
TEST
ACTION
APPLICABILITY
2
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8443 Clockspring cable and jumper harness to
the Clockspring connector.
Turn the ignition on.
Reconnect the battery.
With the DRBIII
t, read the active Airbag DTC’s.
Does the DRB show DRIVER SQUIB CIRCUIT OPEN?
All
Yes
→
No
→
Replace the Clockspring.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
3
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Clockspring connector.
Disconnect the ACM connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 ACM Adaptor to the Airbag Control
Module connector.
Measure the resistance of the Driver Airbag Line 1 circuit between the ACM Adaptor
and the Clockspring connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Repair the Driver Airbag Line 1 circuit for an open or high
resistance
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting airbag system components the ignition must be
turned off and the battery must be disconnected.
33
AIRBAG
DRIVER SQUIB CIRCUIT OPEN - ACTIVE —
Continued
TEST
ACTION
APPLICABILITY
4
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Clockspring connector.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 ACM Adaptor to the Airbag Control
Module connector.
Measure the resistance of the Driver Airbag Line 2 circuit between the ACM Adaptor
and the Clockspring connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Repair the Driver Airbag Line 2 circuit for an open or high
resistance.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
5
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG MODULE IS DROPPED AT ANY TIME, IT MUST
BE REPLACED.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
34
AIRBAG
DRIVER SQUIB CIRCUIT OPEN - ACTIVE —
Continued
Symptom:
DRIVER SQUIB CIRCUIT SHORT - ACTIVE
When Monitored and Set Condition:
DRIVER SQUIB CIRCUIT SHORT - ACTIVE
When Monitored:
When the ignition is on, the ACM monitors the resistance of the Driver
Squib circuits.
Set Condition:
The ACM has detected low resistance on the Driver Squib circuits.
POSSIBLE CAUSES
DRIVER AIRBAG LINE 1 SHORT TO LINE 2
CLOCKSPRING, DAB LINE 1 SHORT TO LINE 2
DRIVER AIRBAG CIRCUIT LINE 1 SHORT TO LINE 2
ACM, DRIVER AIRBAG CIRCUIT SHORT
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 brown cable and jumper harness to the
Driver Airbag connector.
Turn the ignition on, then reconnect the battery.
With the DRBIII
t, read the active Airbag DTCs.
Does the DRB show DRIVER SQUIB CIRCUIT SHORT?
All
Yes
→
No
→
Replace Driver Airbag Module.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
35
AIRBAG
TEST
ACTION
APPLICABILITY
2
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
Disconnect the Clockspring connector.
Note: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8443 Clockspring cable and jumper harness to
the Clockspring connector.
Turn ignition on, then reconnect the battery.
With the DRBIII
t, read the active Airbag DTCs
Does the DRB show DRIVER SQUIB CIRCUIT SHORT?
All
Yes
→
No
→
Replace Clockspring.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
3
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the ACM connector.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 ACM Adaptor to the Airbag Control
Module connector.
Measure the resistance between the Driver Airbag Line 1 and Line 2 at the
Clockspring connector.
Is the resistance below 10.0K ohms?
All
Yes
→
Repair Driver Airbag Line 1 circuit for a short to Driver Airbag
Line 2 circuit.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→
Note: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
36
AIRBAG
DRIVER SQUIB CIRCUIT SHORT - ACTIVE —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст