Dodge Dakota (R1). Manual — part 774
(4) Install bolts attaching fender to hood hinge
support bracket.
(5) Install bolts attaching fender to lower radiator
closure panel.
(6) Install bolt attaching fender to lower rocker
panel.
(7) Position the wire harnesses on the inner fender
and wheelhouse and engage clips.
(8) Install powertrain control module.
(9) Install air cleaner element housing.
(10) Install right headlamp module.
(11) Install wheelhouse liner.
(12) Install wheel opening molding.
(13) Install right front wheel.
(14) Remove the support and lower the vehicle.
(15) Connect battery negative cable.
ROOF JOINT MOLDING
REMOVAL
(1) Warm the roof joint molding and roof panel to
approximately 38°C (100°F) using a suitable heat
lamp or heat gun.
(2) Pull molding from roof joint.
INSTALLATION
(1) Remove adhesive tape residue from roof joint.
(2) If molding is to be reused, remove tape residue
from back of molding. Clean molding with MOPAR,
Super Kleen solvent or equivalent. Wipe molding dry
with lint free cloth. Apply new body side molding
(two sided adhesive) tape to back of molding.
(3) Clean roof joint with MOPAR, Super Kleen sol-
vent or equivalent. Wipe dry with lint free cloth.
(4) Remove protective cover from tape on back of
molding and apply molding to roof joint.
(5) Heat roof and molding, see step one. Firmly
press molding into roof joint to assure adhesion.
SIDE VIEW MIRROR
REMOVAL
(1) Remove door trim panel.
(2) Remove mirror flag seal (Fig. 12).
(3) Disengage power mirror wire connector from
door harness, if equipped (Fig. 13).
(4) Remove nuts attaching side view mirror to door
frame.
(5) Separate harness grommet form door frame, if
equipped.
Fig. 11 Front Fender
1 - U-NUT
2 - U-NUT
3 - FRONT FENDER
4 - RADIATOR CLOSURE PANEL
23 - 84
EXTERIOR
AN
RIGHT FRONT FENDER (Continued)
(6) Separate side view mirror from vehicle.
INSTALLATION
(1) Position side view mirror on vehicle.
(2) Install harness grommet in door frame, if
equipped.
(3) Install nuts attaching side view mirror to door
frame. Tighten nuts to 7 N·m (65 in. lbs.) torque.
(4) Engage power mirror wire connector from door
harness, if equipped.
(5) Install mirror flag seal.
(6) Install door trim panel.
WHEEL OPENING MOLDING
REMOVAL
(1) Remove the screws attaching the wheel open-
ing molding to the fender (Fig. 1).
(2) Separate the molding from the wheel opening.
INSTALLATION
(1) Clean body surface with MOPAR Super Kleen
solvent or equivalent. Wipe surface dry with lint free
cloth.
(2) Position the molding in the wheel opening.
(3) Remove the backing and press to secure mold-
ing.
(4) Install the screws attaching the wheel opening
molding to the fender.
Fig. 12 Mirror Flag Door Seal
1 - STUFFERS
2 - MIRROR FLAG SEAL
Fig. 13 Side View Mirror Connectors
1 - ELECTRIC FOLD AWAY SIDEVIEW MIRROR
2 - DOOR
3 - ELECTRIC SIDEVIEW MIRROR
AN
EXTERIOR
23 - 85
SIDE VIEW MIRROR (Continued)
HOOD
TABLE OF CONTENTS
page
page
HOOD HINGE
HOOD
HOOD SILENCER PAD
HOOD LATCH
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
HOOD RELEASE CABLE
LATCH STRIKER
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . 89
HOOD SAFETY LATCH
HOOD HINGE
REMOVAL
(1) Open hood and support the side that requires
hinge replacement.
(2) Remove cowl grille.
(3) Mark all bolt and hinge attachment locations
with a grease pencil or other suitable device to pro-
vide reference marks for installation.
(4) Remove the nuts attaching the hinge to the
hood (Fig. 1).
(5) Remove the bolts attaching the hinge to the
inner fender (Fig. 1).
(6) Separate hinge from vehicle.
INSTALLATION
(1) If necessary, paint new hinge before installa-
tion.
(2) Position the hinge on the vehicle and align all
marks.
(3) Install the bolts attaching the hinge to the
inner fender. Tighten the bolts to 28.2 N·m (250 in.
lbs.) torque.
(4) Install the nuts attaching the hinge to the
hood. Tighten the nuts to 22.6 N·m (200 in. lbs )
torque.
(5) Install cowl grille.
(6) Remove support and verify hood operation. The
hood should be aligned to 5 mm (0.2 in.) gap to the
front fenders.
HOOD
REMOVAL
(1) Release primary hood latch.
(2) Release hood safety catch and open hood.
(3) Disconnect the under hood lamp wire connec-
tor.
(4) Mark all nut and hinge attachment locations
with a grease pencil or other suitable device to pro-
vide reference marks for installation.
(5) Remove the top nuts attaching hood to hinge
and loosen the bottom nuts until they can be
removed by hand (Fig. 2).
(6) With assistance of a helper, support the hood at
the opposite side of the vehicle.
(7) Remove the bottom nuts and separate the hood
from the vehicle.
Fig. 1 Hood Hinge
1 - HOOD
2 - HOOD HINGE
23 - 86
HOOD
AN
INSTALLATION
(1) With assistance of a helper, position the hood
on hinges.
(2) Align all marks and install the nuts. The hood
should be aligned to 5 mm (0.2 in.) gap to the front
fenders and flush across the top surfaces along fend-
ers.
(3) Connect the under hood lamp wire connector.
(4) Close hood and adjust as necessary.
ADJUSTMENTS
(1) Loosen the hinge arm-to-hood panel bolts at
each side of the vehicle.
(2) Loosen the hood latch screws.
(3) Close the hood. Adjust the fore/aft position.
(4) Raise the hood. Tighten the hinge arm-to-hood
panel bolts.
(5) Tighten the latch screws.
(6) Lower the hood. Inspect clearance between the
hood and the cowl cover.
HOOD SILENCER PAD
REMOVAL
(1) Raise the hood.
(2) Remove the retainers attaching the silencer
pad to the hood (Fig. 3).
(3) Remove the silencer pad from the hood.
INSTALLATION
(1) Position the silencer pad on the hood.
(2) Install the retainers attaching the silencer pad
to the hood.
(3) Close the hood.
HOOD LATCH
REMOVAL
(1) Release primary hood latch.
(2) Release hood safety catch and open hood.
(3) Using a grease pencil, mark latch position for
installation alignment.
(4) Remove bolts attaching hood latch to radiator
closure panel crossmember (Fig. 4).
(5) Separate hood latch from crossmember.
(6) Disconnect release cable from hood latch (Fig.
5).
Fig. 2 Hood
1 - HOOD
2 - HOOD HINGE
Fig. 3 Hood Silencer Pad
1 - HOOD
2 - RETAINER
3 - HOOD SILENCER PAD
Fig. 4 Hood Latch
1 - RADIATOR CLOSURE PANEL
2 - HOOD RELEASE CABLE
3 - HOOD LATCH
4 - LATCH BRACKET
AN
HOOD
23 - 87
HOOD (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст