Dodge Nitro. Manual — part 628
Disconnect the Park Lamp harness connector.
Measure the resistance of the (L17)(L217) Fused Park Lamp Control circuits between the Park Lamp
Harness Connectors and the TIPM C5 harness connector.
Does the ohm meter read open circuit?
Yes
Repair the (L17)(L217) Fused Park Lamp Control circuits for an open.
Perform BODY VERIFICATION TEST - VER 1 .
No
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
B166C-LEFT TRAILER TOW LAMP CONTROL CIRCUIT HIGH
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
With the ignition on.
Set Condition:
The Totally Integrated Power Module (TIPM) detects an HIGH condition.
Diagnostic Test
1) TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, clear all DTC's
Turn on the Left Turn Signal.
With the scan tool, read DTC's.
Possible Causes
(L673) LEFT TRAILER TOW LAMP CONTROL CIRCUIT OPEN
(L673) LEFT TRAILER TOW LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
TOTALLY INTEGRATED POWER MODULE
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Does the scan tool display active: B166C-LEFT TRAILER TOW LAMP CONTROL CIRCUIT
HIGH?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) (L673) LEFT TRAILER TOW LAMP CONTROL CIRCUIT OPEN
Turn the ignition off.
Disconnect the TIPM C6 harness connector.
Disconnect the Left Trailer Tow Lamp harness connectors.
Measure the resistance of the (L673) Left Trailer Tow Lamp Control circuit between the Left Trailer Tow
Lamp harness connectors and the TIPM C6 harness connector.
Does the ohm meter read open circuit?
Yes
Repair the (L673) Left Trailer Tow Lamp Control circuit for an open.
Perform BODY VERIFICATION TEST - VER 1 .
No
Go to 3).
3) (L673) LEFT TRAILER TOW LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
Turn the ignition on.
Measure the voltage on the (L673) Left Trailer Tow Lamp Control circuit.
Is there any voltage present?
Yes
Repair the (L673) Left Trailer Tow Lamp Control circuit for a short to voltage.
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Perform BODY VERIFICATION TEST - VER 1 .
No
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
B166F-RIGHT TRAILER TOW LAMP CONTROL CIRCUIT LOW
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
With the ignition on.
Set Condition:
The Totally Integrated Power Module (TIPM) Detects a LOW condition.
Diagnostic Test
1) INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, clear all DTC's.
Turn on the Right Turn Signal.
With the scan tool, read DTC's.
Does the scan tool display active: B166F-RIGHT TRAILER TOW LAMP CONTROL CIRCUIT
LOW?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
Possible Causes
(L674) RIGHT TRAILER TOW LAMP CONTROL CIRCUIT SHORT TO GROUND
TOTALLY INTEGRATED POWER MODULE
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) (L674) RIGHT TRAILER TOW LAMP CONTROL CIRCUIT SHORT TO GROUND
Turn the ignition off.
Disconnect the TIPM C6 harness connector.
Measure the resistance between ground and the (L674) Right Trailer Tow Lamp Control circuit.
Is the resistance above 10k ohms?
Yes
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
No
Repair the (L674) Right Trailer Tow Lamp Control circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1 .
B1670-RIGHT TRAILER TOW LAMP CONTROL CIRCUIT HIGH
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
Continuously
Set Condition:
The Totally Integrated Power Module (TIPM) Detects a HIGH condition.
Diagnostic Test
1) TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
Possible Causes
(L674) RIGHT TRAILER TOW LAMP CONTROL CIRCUIT OPEN
(L674) RIGHT TRAILER TOW LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
TOTALLY INTEGRATED POWER MODULE
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст