Dodge Nitro. Manual — part 447
service. Disconnect and isolate the battery negative (ground) cable, then
wait two minutes for the system capacitor to discharge before performing
further diagnosis or service. This is the only sure way to disable the
supplemental restraint system. Failure to take the proper precautions
could result in accidental airbag deployment.
WARNING:
To avoid serious or fatal injury on vehicles equipped with airbags, before
performing any welding operations disconnect and isolate the battery
negative (ground) cable and disconnect all wire harness connectors from
the Occupant Restraint Controller (ORC). Failure to take the proper
precautions could result in accidental airbag deployment and other
possible damage to the supplemental restraint system circuits and
components.
WARNING:
To avoid serious or fatal injury, do not attempt to dismantle an airbag unit
or tamper with its inflator. Do not puncture, incinerate, or bring into
contact with electricity. Do not store at temperatures exceeding 93°C
(200°F). An airbag inflator unit may contain sodium azide and potassium
nitrate. These materials are poisonous and extremely flammable. Contact
with acid, water, or heavy metals may produce harmful and irritating
gases (sodium hydroxide is formed in the presence of moisture) or
combustible compounds. An airbag inflator unit may also contain a gas
canister pressurized to over 17.24 kPa (2500 psi).
WARNING:
To avoid serious or fatal injury when handling a seat belt tensioner
retractor, proper care should be exercised to keep fingers out from under
the retractor cover and away from the seat belt webbing where it exits
from the retractor cover.
WARNING:
To avoid serious or fatal injury, replace all restraint system components
only with parts specified in the DaimlerChrysler Mopar® Parts Catalog.
Substitute parts may appear interchangeable, but internal differences may
result in inferior occupant protection.
WARNING:
To avoid serious or fatal injury, the fasteners, screws, and bolts originally
used for the restraint system components must never be replaced with
any substitutes. These fasteners have special coatings and are
specifically designed for the restraint system. Any time a new fastener is
needed, replace it with the correct fasteners provided in the service
package or specified in the DaimlerChrysler Mopar® Parts Catalog.
WARNING:
To avoid serious or fatal injury when a steering column has an airbag unit
attached, never place the column on the floor or any other surface with
the steering wheel or airbag unit face down.
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Body - Nitro
SEAT - FRONT
DESCRIPTION
DESCRIPTION
Fig. 447: Drivers Seat 2 Way Assembly
Courtesy of CHRYSLER LLC
1 - BAG, BSR
20 - RECLINER, HANDLE ASSEMBLY
2 - CUSHION, BACK
21 - SCREW
3 - HEADREST, GUIDE WITHOUT BUTTON
22 - SCREW
4 - HEADREST, ASSEMBLY
23 - SHIELD
5 - BOLT, SEAT BELT 47.5 N.m (35 ft. lbs.)
24 - SHIELD
6 - HEADREST, GUIDE WITH LOCK AND
BUTTON
25 - SHIELD
7 - CUSHION, SEAT
26 - RIVET
8 - PRETENSIONER, ASSEMBLY
27 - WIRE, SHIELD ATTACHMENT
9 - SHIELD, ASSEMBLY
28 - HARNESS, ASSEMBLY
10 - SCREW
29 - RISER, LH OUTBOARD
11 - SHIELD
30 - NUT 27.5 N.m (20 ft. lbs.)
12 - FRAME, SEAT
31 - RISER, LH INBOARD
13 - SCREW, M10 47.5 N.m (35 ft. lbs.)
32 - COVER, SEAT
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Body - Nitro
Fig. 448: Drivers Seat 6 Way Assembly
Courtesy of CHRYSLER LLC
14 - FRAME, SEAT BACK
33 - ELEMENT, HEATED SEAT
15 - PLATE, ROUTING
34 - ELEMENT, HEATED SEAT BACK
16 - PIN, PUSH
35 - COVER, SEAT BACK
17 - SCREW
36 - COVER, HEAD REST
18 - SHIELD
37 - SENSOR, SEAT TRACK POSITION
19 - SCREW, M10 47.5 N.m (35 ft. lbs.)
-
1 - BAG, BSR
22 - PLATE, ROUTING
2 - CUSHION, BACK
23 - SCREW
3 - HEADREST, GUIDE WITHOUT BUTTON
24 - RIVET
4 - HEADREST, ASSEMBLY
25 - SHIELD
5 - HEADREST, GUIDE WITH LOCK
26 - SCREW
6 - BOLT, SEAT BELT 47.5 N.m (35 ft. lbs.)
27 - SHIELD
7 - CUSHION, SEAT
28 - SCREW
8 - PRETENSIONER, ASSEMBLY
29 - SHIELD, CLOSEOUT
9 - SHIELD, ASSEMBLY
30 - SHIELD, POWER SWITCH
10 - FRAME, SEAT
31 - SHIELD, POWER SEAT
11 - SCREW, M10 47.5 N.m (35 ft. lbs.)
32 - WIRE, SHIELD ATTACHMENT
12 - SHIELD
33 - HARNESS, 6 WAY POWER
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Body - Nitro
Fig. 449: Passenger Seat Domestic Assembly
Courtesy of CHRYSLER LLC
13 - SCREW
34- RISER, LH OUTBOARD
14 - RISER, LH INBOARD
35 - NUT 27.5 N.m (20 ft. lbs.)
15 - SCREW
36 - COVER, SEAT
16 - FRAME, SEAT BACK
37 - ELEMENT, HEATED SEAT BACK
17 - PIN, PUSH
38 - ELEMENT, HEATED SEAT
18 - SHIELD
39 - COVER, SEAT BACK
19 - SHIELD
40 - COVER, HEAD REST
20 - RECLINER, HANDLE ASSEMBLY
41 - SENSOR, SEAT TRACK POSITION
21 - SCREW, M10 47.5 N.m (35 ft. lbs.)
-
1 - BAG, BSR
26 - BOLT, SEAT BELT
2 - HEADREST, GUIDE WITHOUT BUTTON
27 - SCREW
3 - HEADREST, ASSEMBLY
28 - CABLE, RELEASE
4 - HEADREST, GUIDE WITH LOCK
29 - FRAME, SEAT
5 - SHIELD, CLOSEOUT
30 - SENSOR, SEAT TRACK POSITION
6 - SCREW
31 - HARNESS, ASSEMBLY
7 - SHIELD, ASSEMBLY
32 - GAGE, STRAIN TI
8 - SCREW
33 - NUT 27.5 N.m (20 ft. lbs.)
9 - RIVET
34 - RISER
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Body - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст