Dodge Viper SRT-10 (ZB). Manual — part 7
Fig. 1 Lubrication Points - Overhead View
1 - FRONT LOWER BALL JOINTS
2 - FRONT UPPER BALL JOINTS
3 - REAR LOWER BALL JOINTS
4 - REAR UPPER BALL JOINTS
2 - 2
SUSPENSION
ZB
SUSPENSION (Continued)
FRONT SUSPENSION
TABLE OF CONTENTS
page
page
FRONT SUSPENSION
FRONT SUSPENSION FASTENER TORQUE
. . . . . . . . . . . . . . . . . . . 4
HUB / BEARING
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIAGNOSIS AND TESTING - HUB AND
. . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . 7
KNUCKLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . 8
KNUCKLE/ABS TONE WHEEL SEAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . 10
LOWER BALL JOINT
. . . . . . . . . . . . . . . . . . . . . . . . . 11
DIAGNOSIS AND TESTING - LOWER BALL
. . . . . . . . . . . . . . . . . . . . . . . 11
LOWER BALL JOINT SEAL BOOT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . 12
LOWER CONTROL ARM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DISASSEMBLY - LOWER CONTROL ARM
. . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 16
SHOCK ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
STABILIZER BAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . 21
STABILIZER BAR BUSHINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . 21
STABILIZER LINK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
UPPER BALL JOINT
. . . . . . . . . . . . . . . . . . . . . . . . . 22
DIAGNOSIS AND TESTING - UPPER BALL
. . . . . . . . . . . . . . . . . . . . . . . 23
UPPER BALL JOINT SEAL BOOT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 23
UPPER CONTROL ARM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DISASSEMBLY - UPPER CONTROL ARM
. . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 26
ZB
FRONT SUSPENSION
2 - 3
FRONT SUSPENSION
SPECIFICATIONS
FRONT SUSPENSION FASTENER TORQUE
DESCRIPTION
N·m
Ft.
Lbs.
In.
Lbs.
ABS Tone Wheel Mounting
Bolt
17
13
150
Brake Caliper (Hydraulic)
Mounting Bolts
115
85
—
Hub And Bearing Mounting
Bolts
61
45
—
Lower Ball Joint Castle Nut
160
118
—
Lower Control Arm Pivot
Cam Bolts
102
75
—
Shock Assembly Mounting
Bolts (Lower and Upper)
136
100
—
Stabilizer Bar Bushing
Retainer Bolts
68
50
—
Stabilizer Link Control Arm
Nut
23
17
200
Stabilizer Link Stabilizer Bar
Nut
23
17
200
Tie Rod Knuckle Nut
75
55
—
Tie Rod Adjuster Jam Nut
75
55
—
Upper Ball Joint Castle Nut
102
75
—
Upper Control Arm Frame
Bolts
102
75
—
Wheel Mounting (Lug) Nuts
122
90
—
SPECIAL TOOLS
FRONT SUSPENSION
Installer, Bearing/Seal 6573
Installer, Ball Joint 6761
Height Gages, Suspension 6914
Remover/Installer, Bushing 6969B
Spacer, Control Arm Removing 6983
2 - 4
FRONT SUSPENSION
ZB
HUB / BEARING
DESCRIPTION
The wheel bearing used on the front of this vehicle
is a unit type combined hub and bearing assembly
(Fig. 1). The hub and bearing is made up of the
wheel mounting hub (flange) and the wheel bearing.
The hub has six wheel mounting studs installed in it.
It is held together using a clamp bolt and nut that is
torqued and crimped in place when assembled. The
clamp bolt is not serviceable and no attempt should
ever be made to remove it from the hub and bearing.
The hub and bearing assembly is mounted to the
steering knuckle and is retained by four mounting
bolts accessible from the back of the knuckle.
The bearing requires no periodic maintenance. The
hub and bearing is serviced as an assembly if the
hub or bearing is determined to be defective. The
wheel mounting studs may be replaced separately if
necessary.
DIAGNOSIS AND TESTING - HUB AND
BEARING (FRONT)
With the wheel, disc brake caliper, and brake rotor
removed, rotate the wheel hub. Any roughness or
resistance to rotation may indicate dirt intrusion or a
failed wheel bearing. If the bearing exhibits any of
these conditions during diagnosis, replace the hub
and bearing. The bearing is not serviceable.
Damaged bearing seals and the resulting excessive
grease loss may also require hub and bearing
replacement. Moderate grease seepage from the bear-
ing is considered normal and should not require
replacement of the hub and bearing.
Stands, Suspension Height 9096
Remover, Ball Joint C-4150A
Handle, Drive C-4171
Remover, Tie Rod End MB991113
Fig. 1 Hub And Bearing
1 - WHEEL MOUNTING HUB
2 - HUB/BEARING ASSEMBLY
3 - CLAMP BOLT/NUT
4 - WHEEL MOUNTING STUD
ZB
FRONT SUSPENSION
2 - 5
FRONT SUSPENSION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст