Dodge Viper SRT-10 (ZB). Manual — part 57
REMOVAL
DOOR SPEAKER
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the speaker grill fasteners (Fig. 8).
(3) Remove the speaker fasteners.
(4) Disconnect the wire harness connector and
remove speaker.
INSTRUMENT PANEL SPEAKER
(1) Disconnect and isolate the battery negative
cable.
(2) Using a trim stick, remove the speaker grill
(Fig. 9).
(3) Remove the speaker fasteners.
(4) Disconnect the wire harness connector and
remove speaker.
REAR SPEAKER
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the bulkhead quarter trim panel (Refer
to 23 - BODY/INTERIOR/BULKHEAD TRIM PANEL
- REMOVAL).
(3) Remove the mounting fasteners.
(4) Disconnect the electrical harness connector and
remove speaker (Fig. 10).
SUB WOOFER
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the bulkhead quarter trim panel (Refer
to 23 - BODY/INTERIOR/BULKHEAD TRIM PANEL
- REMOVAL).
(3) Remove the mounting fasteners (Fig. 11).
(4) Disconnect the electrical harness connector and
remove subwoofer.
INSTALLATION
DOOR SPEAKER
(1) Connect wire harness connector and position
speaker.
(2) Install mounting fasteners. Tighten to 3 N·m
(24 in. lbs.).
(3) Install the speaker grill mounting fasteners.
(4) Connect the battery negative cable.
Fig. 8 DOOR SPEAKER
1 - DOOR SPEAKER
2 - ELECTRICAL HARNESS CONNECTOR
3 - MOUNTING SCREW
4 - SPEAKER GRILL
Fig. 9 INSTRUMENT PANEL SPEAKER
Fig. 10 REAR SPEAKER
8A - 10
AUDIO/VIDEO
ZB
SPEAKER (Continued)
INSTRUMENT PANEL SPEAKER
(1) Connect wire harness connector and position
speaker.
(2) Install mounting fasteners. Tighten to 2 N·m
(19 in. lbs.).
(3) Install the speaker grill.
(4) Connect the battery negative cable.
REAR SPEAKER
(1) Connect wire harness connector and position
speaker.
(2) Install mounting fasteners.
(3) Install the bulkhead quarter trim panel (Refer
to 23 - BODY/INTERIOR/BULKHEAD TRIM PANEL
- INSTALLATION).
(4) Connect the battery negative cable.
SUB WOOFER
(1) Connect wire harness connector and position
sub woofer.
(2) Install mounting fasteners. Tighten to 6 N·m
(50 in. lbs.).
(3) Install the bulkhead quarter trim panel (Refer
to 23 - BODY/INTERIOR/BULKHEAD TRIM PANEL
- INSTALLATION).
(4) Connect the battery negative cable.
Fig. 11 SUB WOOFER
1 - SUBWOOFER
2 - MOUNTING SCREW
3 - MOUNTING NUT
ZB
AUDIO/VIDEO
8A - 11
SPEAKER (Continued)
CHIME/BUZZER
TABLE OF CONTENTS
page
page
CHIME/BUZZER
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
CHIME/BUZZER
DESCRIPTION
The chime/buzzer is located within the ElectroMe-
chanical Instrument Cluster (EMIC), and is not ser-
viceable. The chime/buzzer system provides the
driver with warning chimes for:
• Airbag System Malfunction
• Antilock Brake System Malfunction
• Critical Coolant Temperature
• Critical Oil Temperature
• Deck Lid Ajar
• Door Ajar
• Exterior Lamps ON
• Interior Lamps ON
• Key-In Ignition
• Low Brake Fluid
• Low Fuel
• Park Brake
• Seat Belt and Seat Belt Reminder
• Service Engine Soon
• Tire Pressure System
• Under & Over Charging Voltage
• Voltage
OPERATION
AIRBAG WARNING
The ElectroMechanical Instrument Cluster (EMIC)
monitors airbag systems via the Programmable Com-
munication Interface (PCI) data bus from the Occu-
pant Restraint Controller (ORC). The ORC will
transmit a message once per second, over the PCI
data bus, as to whether the warning indicator should
be ON or OFF. The warning indicator indicates that
a part of the airbag system is inoperative and needs
to be serviced as soon as possible. If the instrument
cluster does not receive a message from the ORC for
3 consecutive seconds, the instrument cluster will
illuminate the warning indicator. The ORC transmits
a PCI data bus message requesting the instrument
cluster to perform a bulb check each time the igni-
tion is turned to the ON position.
ANTILOCK BRAKE WARNING
The ElectroMechanical Instrument Cluster (EMIC)
monitors the ABS message and chimes a single
chime warning whenever the ABS module requests
the ABS light on. If the EMIC does not receive a
message from the ABS module for more than 5 sec-
onds, the EMIC will light the ABS light and request
a single chime warning.
CRITICAL COOLANT TEMPERATURE WARNING
The EMIC monitors the engine coolant tempera-
ture message from the PCM and requests a single
chime when the temperature is high (245 F) and a
continuous chime when the temperature is critical
(equal to or above 260 F).
CRITICAL OIL TEMPERATURE WARNING
The EMIC monitors the engine oil temperature
message from the PCM and requests a single chime
when the temperature is high (290 F) and a contin-
uous chime when the temperature is critical (equal to
or above 300 F).
DECK LID AJAR REMINDER
The BCM monitors the deck lid ajar switch. A
chime will sound once when the deck lid is opened,
the ignition is in RUN position and vehicle speed is
present.
DOME LAMPS ON REMINDER
The BCM monitors the dome/dimmer switch. The
Dome ON audible warning will alert the driver that
the interior lamps have been left ON. If the ignition
switch is left OFF, the drivers door open, and the
dimmer switch is in the DOME position, the chime
will sound until the dimmer switch is turned out of
DOME, the door is closed or the interior lighting bat-
tery protection time out expires (15 minutes).
DOOR AJAR WARNING
The BCM monitors the door ajar switches. A chime
will sound once when the door is opened, the ignition
is in RUN position and vehicle speed is present.
ZB
CHIME/BUZZER
8B - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст