Dodge Viper SRT-10 (ZB). Manual — part 364
Symptom:
PASSENGER WINDOW DOWN RELAY COIL OPEN/SHORT TO
GROUND
When Monitored and Set Condition:
PASSENGER WINDOW DOWN RELAY COIL OPEN/SHORT TO GROUND
When Monitored:
Whenever the ignition is in the Run or Accessory position.
Set Condition:
When the BCM turns on the Passenger Window Down Relay Control
circuit and does not detect 8.0 volts or greater within 10 seconds, this code will set.
POSSIBLE CAUSES
DTC PRESENT
RELAY COIL OPEN/SHORTED
RELAY FUSED B+ OPEN
PASSENGER WINDOW DOWN RELAY CONTROL WIRE OPEN
PASSENGER WINDOW DOWN RELAY CONTROL WIRE SHORT TO GROUND
BODY CONTROL MODULE - PASSENGER WINDOW DOWN RELAY CONTROL OPEN/SHORT TO
GROUND
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Try to operate the Passenger Window Motor several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display PASSENGER WINDOW DOWN RELAY COIL OPEN/
SHORT TO GROUND?
All
Yes
→ Go To 2
No
→ The condition that caused the code to set is not present at this
time. Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
349
POWER WINDOWS
TEST
ACTION
APPLICABILITY
2
NOTE: The Passenger Window Down Relay is located left of the steering
column and taped to the harness.
Remove the Passenger Window Down Relay.
Install a substitute Relay in place of the Passenger Window Down Relay.
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Press the Passenger Window Switch DOWN several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display PASSENGER WINDOW DOWN RELAY OPEN/SHORT
TO GROUND?
All
Yes
→ Go To 3
No
→ Replace the Window Relay.
Perform BODY VERIFICATION TEST - VER 1.
3
NOTE: The Passenger Window Down Relay is located left of the steering
column and taped to the harness.
Remove the Passenger Window Down Relay.
Measure the voltage between the Fused B+ circuit and ground in the relay connector.
Is the voltage above 10.0 volts?
All
Yes
→ Go To 4
No
→ Repair the Fused B+ circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off.
NOTE: The Passenger Window Down Relay is located left of the steering
column and taped to the harness.
Remove the Passenger Window Down Relay.
Disconnect the BCM C3 harness connector.
Measure the resistance between ground and the Passenger Window Down Relay
Control circuit in the BCM C3 connector.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Passenger Window Down Relay Control circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off.
NOTE: The Passenger Window Down Relay is located left of the steering
column and taped to the harness.
Remove the Passenger Window Down Relay.
Disconnect the BCM C4 harness connector.
Measure the resistance of the Passenger Window Down Relay Control circuit
between the BCM C4 connector and the Relay connector..
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Passenger Window Down Relay Control circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
350
POWER WINDOWS
PASSENGER WINDOW DOWN RELAY COIL OPEN/SHORT TO GROUND
—
Continued
Symptom:
PASSENGER WINDOW DOWN RELAY COIL SHORT TO BATTERY
When Monitored and Set Condition:
PASSENGER WINDOW DOWN RELAY COIL SHORT TO BATTERY
When Monitored:
Whenever the ignition is in the Run or Accessory position and the
window switch is activated down..
Set Condition:
When the BCM grounds the Passenger Window Down Relay Control
circuit and detects a current greater than approximately 250 ma. for over 125 milliseconds,
this code will set.
POSSIBLE CAUSES
DTC PRESENT
RELAY SHORTED
PASSENGER WINDOW DOWN RELAY CONTROL WIRE SHORT TO BATTERY
BODY CONTROL MODULE - PASSENGER WINDOW DOWN RELAY CONTROL SHORTED
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Try to operate the Passenger Window Motor several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display PASSENGER WINDOW DOWN SHORTED TO BAT-
TERY?
All
Yes
→ Go To 2
No
→ The condition that caused the code to set is not present at this
time. Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
2
NOTE: The Passenger Window Down Relay is located left of the steering
column and taped to the harness.
Remove the Passenger Window Down Relay.
Install a substitute Relay in place of the Passenger Window Down Relay.
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Press the Passenger Window Switch DOWN several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display PASSENGER WINDOW DOWN SHORTED TO BAT-
TERY?
All
Yes
→ Go To 3
No
→ Replace the Window Relay.
Perform BODY VERIFICATION TEST - VER 1.
351
POWER WINDOWS
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
NOTE: The Passenger Window Down Relay is located left of the steering
column and taped to the harness.
Remove the Passenger Window Down Relay.
Disconnect the BCM C3 harness connector.
Measure the Voltage between ground and the Passenger Window Down Relay
Control circuit.
Is there any voltage present?
All
Yes
→ Repair the Passenger Window Down Relay Control circuit for a
short to Battery.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
352
POWER WINDOWS
PASSENGER WINDOW DOWN RELAY COIL SHORT TO BATTERY —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст