Dodge Viper SRT-10 (ZB). Manual — part 230
Description
N·m
Ft. Lbs.
In. Lbs.
Door window regulator nuts
12
9
—
Fender support fasteners
17
13
—
Fuel filler door screws
7
—
65
Hood hinge to body bolts
28
21
—
Hood hinge to hood bolts
12
9
—
Hood latch nuts
12
9
—
Instrument panel left mounting bracket bolt & nut
28
21
—
Instrument panel lower front mounting bolts
12
9
—
Instrument panel mounting nuts
28
21
—
Quarter panel door sill screws
6
—
55
Quarter panel rear screws
6
—
55
Quarter panel to fascia screws
6
—
55
Quarter panel top screws
6
—
55
Side view mirror nuts
7
—
65
Trunk pan bolts - fuel pump cover area
9
—
80
Trunk pan front support bracket nuts
12
9
—
Trunk pan outside bolts
6
—
55
Trunk pan trunk area bolts
28
21
—
Trunk pan wheelhouse bracket bolts
6
—
55
Windshield header & a-pillar weatherstrip nuts
6
—
55
SPECIAL TOOLS
BODY
STICK, TRIM C 4755
23 - 12
BODY
ZB
BODY (Continued)
CONVERTIBLE TOP
TABLE OF CONTENTS
page
page
CONVERTIBLE TOP
. . . . . . . . . . . . . . . . . . . . . . . . . 13
FOLDING TOP COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
FOLDING TOP - ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 16
REAR WINDOW
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . 17
STAY PADS - STRAPS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . 18
BOW - CENTER/3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
BOW - REAR/4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
CLOTH SUPPORT PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 19
HEADER ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 19
TACK STRIP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 19
TENSION CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . 21
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . 21
HINGE - SIDEARM/LINKAGE ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . 21
CONVERTIBLE TOP
DESCRIPTION
ZB
CONVERTIBLE TOP
23 - 13
Fig.
1
EXPLODED
VIEW
23 - 14
CONVERTIBLE TOP
ZB
CONVERTIBLE TOP (Continued)
FOLDING TOP COVER
REMOVAL
(1) Roll down both door windows.
(2) Unlatch the convertible top.
(3) Remove the front and rear weatherstrip retain-
ers. (Fig. 1)
(4) Remove the two rivets at the bottom of cover
assembly to the side arm assembly on both sides.
(5) Remove the tension cable rivets.
(6) Pull tension cable through the cover assembly.
(7) Pull off the trim welt and uncover the tack
strips.
(8) Pull the staples from the welt.
(9) Disconnect the rear window defroster electrical
connectors. (Fig. 2)
(10) Remove the 14 tack strip nuts. (Fig. 3)
(11) Pull the staples from the side panels.
(12) Flip the top cover up.
(13) Remove the staples from the cover assembly
to the rear/4 bow.
(14) Remove the 11 screws and remove the seal
compression panel.
(15) Remove the staples from the cover assembly
to the header assembly.
(16) Flip the cover over at the front and remove
the rivets at the center/3 bow.
(17) Remove the cover assembly.
INSTALLATION
(1) Using the old cover assembly as a template and
a grease pencil or equivalent, mark the new cover
and trim off the excess material.
(2) Position the new cover and adjust the fit if
required.
(3) Reglue the side of the cover.
(4) Adjust the fit of the side panels if required.
(5) Install new rivets attaching the cover to the
center/3 bow.
(6) Position the cover over the header and staple
into place.
(7) Install the seal compression panel and tighten
the screws to 5 N·m (45 in. lbs.).
(8) Position the rear flap of the cover over the
rear/4 bow and staple into place.
(9) Flip the side panels down and staple into place.
(10) Install the tack strips and install the nuts.
1 = TOP COVER ASSEMBLY
2 = BACKLITE ASSEMBLY
3 = REAR/#4 BOW ASSEMBLY
4 = CENTER/#3 BOW ASSEMBLY
5 = HEADER ASSEMBLY
6 = SCREWS (14)
7 = CLOTH SUPPORT PANEL
8 = LATCH ASSEMBLY
9 = SEAL COMPRESSION PANEL
10 = SCREWS (11)
11 = DOWEL (2)
12 = FRONT RAIL RETAINER
13 = REAR RAIL RETAINER
14 = SIDE ARM/LINKAGE ASSEMBLY
15 = TACK STRIP ASSEMBLY
16 = STAY PAD - STRAP RIVETS (3)
17 = STAY PAD - STRAP
18 = TENSION CABLE (2)
Fig. 2 FOLDING TOP COVER
1 - UNDERBODY WIRING HARNESS
2 - FOLDING TOP COVER ANCHORING
3 - BODY ASSEMBLY
4 - HEATED REAR WINDOW CONNECTOR
5 - REAR WINDOW
Fig. 3 FOLDING TOP ANCHORING STUDS
1 - BODY ASSEMBLY
2 - FOLDING TOP COVER
3 - STUDS (14)
ZB
CONVERTIBLE TOP
23 - 15
FOLDING TOP COVER (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст