Skoda Octavia iV (2021 year). Manual in english — page 3
Lighting, windscreen wipers and washers › Exterior lighting
49
High beam and headlight Ĕasher
Hazard warning light system
The high beam works when the low beam is on.
› Press the button to switch on or off in the mid-
dle part of the control panel.
A
Switch on high beam
The hazard warning lights can be switched on auto-
B
Switch off main
matically during hard braking. The hazard warning
beam / switch on
lights are then switched off again automatically
headlight ĔasheÙ
when starting off or accelerating.
When the main beam or
When the hazard warning system is on and the
headlight ĔasheÙ is
turn signal is switched on, the hazard warning lights
switched on, the indica-
will be switched off temporarily and only the turn
tor lamp lights up in the instrument cluster
signal will Ĕash on the relevant side of the vehicle.
CAUTION
One-sided parking light
Risk of an accident!
The one-sided parking light allows one side of the
▶ Do not dazzle other road users with the high beam.
parked vehicle to be illuminated through activation
Turn signal
of the corresponding sidelights.
A
Switch on the side-
A
Switching on the
turn signal light on
lights on the right
the right - the warn-
B
Switch on the side-
ing light Ĕashes in
lights on the left
the instrument clus-
› Switch off the ignition.
ter
› Move the lever to the
B
Switching on the
appropriate position.
turn signal light on
› Lock the vehicle.
the left - the warn-
ing light Ĕashes in
When the parking light is
the instrument clus-
switched on, an acoustic
ter
warning signal sounds and the driver's door is
opened. After a few seconds or after the driver's
Turn signal - convenience signalling
door is closed, the warning signal will stop.
Convenience signalling enables three Ĕashes of the
turn signal lights without having to move the lever
Double-sided parking light
up or down.
The two-sided parking light allows the parked vehi-
cle to be illuminated through activation of the side-
› Tap the control lever up or down.
lights.
The corresponding turn signal lights Ĕash three
› Turn on the ignition.
times.
› Choose
light mode.
Tap the lever in the opposite direction ahead of
› Switch off the ignition.
time to stop signalling.
›
Lock the vehicle.
Fog light
When the parking light is switched on, an acoustic
Front/rear fog light
warning signal sounds after the ignition is switched
switch
off and the driver's door is opened. After a few sec-
onds or after the driver's door is closed, the warning
A
Fog lights - the
signal will stop.
warning light in the
instrument cluster il-
The light may switch off automatically if the 12-volt
luminates
vehicle battery is too low. If the parking lights on
B
Rear fog light - the
both sides are switched on with the ignition off, the
warning light in the
lights will not be switched off automatically and the
instrument cluster il-
12 volt vehicle battery may be discharged.
luminates
› Switch on the respective switch (for fog lamp/rear
Settings
fog lamp).
Activating/deactivating the automatic headlights
The rear fog light does not illuminate when an ac-
system in rain
cessory is connected to the trailer socket.
› In the Infotainment system, select the menu
Outside .
50
Lighting, windscreen wipers and washers › COMING HOME, LEAVING HOME exterior lighting
› By moving your fiÄ£eÙ sideways, choose the screen
› Select Headlights and actiavte or deactivate the func-
with the menu item Headlights .
tion Travel mode: .
› Select Headlights and activate or deactivate the func-
tion of the automatic driving light switch function
Troubleshooting
when it rains.
Activating/deactivating convenience signalling
Turn signal light defective
› In the Infotainment system, select the menu
Ĕashes faster - turn signal light on the right de-
Outside .
fective
› By moving your fiÄ£eÙ sideways, choose the screen
› Check the turn signal light on the right.
with the menu item Headlights .
Ĕashes faster - turn signal light on the left de-
› Select Headlights and actiavte or deactivate the func-
fective
tion Comfort Ĕasher .
› Check the turn signal light on the left.
Headlamp levelling, LED headlights
› In the Infotainment system, select the menu
does not Ĕash when the trailer is hitched -
Outside .
trailer turn signal light defective
› By moving your fiÄ£eÙ sideways, choose the screen
› Check the trailer lighting.
with the menu item Headlights .
› Select Headlights .
LED bulb or light bulb is defective
› Select the menu item for headlight range control.
illuminates together with
› Adjust the headlight range using the slider. The
Information appears in the display regarding
headlight range must correspond to the vehicle's
the defective lights.
load.
› Seek the help of a specialist garage.
Front seats occupied, boot empty
All seats occupied, boot empty
The headlights are misted up on the inside
Inside the headlights, moisture may occur. This is not
All seats occupied, boot loaded
Driver's seat occupied, boot loaded
a defect.
In the event of another vehicle loading condition, the
Malfunction of the automatic headlight circuit
positions ,
,
can be used.
› Clean the windscreen in the area of the rain/light
sensor.
For the Full LED headlights, the headlight range
control is adjusted automatically.
Beam of light in front of the vehicle has shortened
Headlight defective.
WARNING
Risk of an accident!
› Seek the help of a specialist garage.
An incorrectly adjusted headlight range can cause in-
Driving lights defective
suffiieÄt vehicle lighting or can dazzle other road
If a message regarding the failed driving lights is dis-
users.
played, the light will work in emergency mode.
▶ Adjust the headlight range correctly.
›
Drive on, exercising appropriate caution.
Activate / deactivate the dynamic cornering lights
› Seek the help of a specialist garage.
function
Applies to full LED headlights.
› In the Infotainment system, select the menu
COMING HOME, LEAVING HOME
Outside .
exterior lighting
› By moving your fiÄ£eÙ sideways, choose the screen
with the menu item Headlights .
Functionality
› Select Headlights and actiavte or deactivate the func-
The COMING HOME function turns on the light after
tion Dynamic cornering light .
turning off the ignition and opening the driver's door.
Adjust headlights for driving in right / left-hand
The light switches off automatically after the set
traffic
lighting time has elapsed.
Applies to full LED headlights.
The LEAVING HOME function switches on the light
› In the Infotainment system, select the menu
when unlocking the vehicle with the wireless remote
Outside .
control.
› By moving your fiÄ£eÙ sideways, choose the screen
with the menu item Headlights .
Lighting, windscreen wipers and washers › Light Assist high-beam assist system
51
Operating conditions
▶ The headlights/lights of oncoming vehicles are
covered by crash barriers, for example.
✓ Visibility has worsened.
▶ The headlamps/lights of the oncoming or preced-
✓ The light switch is located in mode
ing vehicle are dirty or not functioning.
Settings
Settings
› In the Infotainment system, select the menu
Activation/deactivation
Outside .
› In the Infotainment system, select the menu
› By moving your fiÄ£eÙ sideways, choose the screen
Outside .
with the menu item Comfort light .
› By moving your fiÄ£eÙ sideways, choose the screen
› Select Comfort light select and set the speed limit.
with the menu item Headlights .
After switching off the ignition, a menu is dis-
› Select Headlights and actiavte or deactivate the func-
played on the Infotainment screen, showing where
tion Light Assist .
the COMING HOME function can be activated/deac-
tivated.
Dynamic Light Assist headlight assist
system
Light Assist high-beam assist system
Functionality
Functionality
The headlight assist system automatically switches
The high beam assist system automatically switches
the high beam on and off.
the high beam on and off.
When the high beam is switched on, it adjusts the
WARNING
light cone so that the drivers of oncoming and pre-
Risk of accident!
ceding vehicles are not dazzled.
▶ If necessary, manually switch the high beam on or
WARNING
off.
Risk of accident!
▶ If necessary, manually switch the high beam on or
off.
Operating conditions
✓ The system is activated.
Operating conditions
✓ The light switch is located in mode
✓ The driving speed is higher than 30 km/h.
✓ The system is activated.
✓ The low beam is switched on.
✓ The light switch is located in mode
✓ The driving speed is higher than 30 km/h (for
some countries, higher than 60 km/h).
Operation
✓ The low beam is switched on.
Switching on
› Push the lever in the
Operation
direction of the arrow.
Switching on
It lights up in the instru-
ment cluster
from
› Push the lever in the
the isolation box.
direction of the arrow.
It lights up in the instru-
ment cluster
from
Switching off
the isolation box.
› Manually switch the high beam on or off.
Switching off
Function restriction
› Manually switch the high beam on or off.
The system may dazzle other road users if their
headlights/lights are not detected for the following
reasons, for example:
52
Lighting, windscreen wipers and washers › Interior lighting
Function restriction
Automatic switching oÄ/off of the footwell light-
ing
The system may dazzle other road users if their
The lighting only works when the dipped or parking
headlights/lights are not detected for the following
lights are on.
reasons, for example:
The lighting is also switched on automatically after
▶ The headlights/lights of oncoming vehicles are
opening the door (e.g. when getting in or out).
covered by crash barriers, for example.
Turn on the lighting for the make-up mirror in the
▶ The headlamps/lights of the oncoming or preced-
sun visors on the windscreen
ing vehicle are dirty or not functioning. The system
can also recognize a vehicle as a single-lane means
› Slide off the cover of the make-up mirror.
of transport.
Settings
Settings
Switch and instrument lighting
Adjusting the brightness of the switch and instru-
Activation/deactivation
ment lighting is done in Infotainment in one of the
› In the Infotainment system, select the menu
following ways:
Outside .
› By moving your fiÄ£eÙ sideways, choose the screen
› Press the bar at the
with the menu item Headlights .
top of the screen and
drag down.
› Select Headlights and actiavte or deactivate the func-
tion Dynamic Light Assist .
A window showing the
slider for setting the
brightness level opens.
Interior lighting
› Adjust the brightness level using the slider.
Operation
Or:
› The menu
Interior .
Switching on automatically
› By moving your fiÄ£eÙ sideways, choose the screen
The lighting switches on when one of the following
with the interior lighting menu item.
events occurs.
›
Select the menu item for the interior lighting and
▶ The vehicle is unlocked
adjust the brightness level using the slider.
▶ One of the doors is opened
Backlight of the infotainment screen and the cen-
▶ The ignition is switched off
tre console
Automatic switch off
Applies to vehicles that do not have the background
The lighting switches off when one of the following
lighting.
events occurs:
The following functions can be set in infotainment:
▶ The vehicle is locked
▶ Setting the lighting colour of the infotainment
▶ The ignition is switched on
screen:
▶ About 45 seconds after all the doors have been
▶ Automatic depending on the selected driving
closed
mode
Operation of the lighting
▶ Manually with the slider
Turn the front and rear lights oÄ/off
▶ Centre console lighting brightness
Deactivation of automatic activation
› The menu
Interior .
(
lights up yellow when deactivated)
›
By moving your fiģe٠sideways, choose the screen
The individual lights can be switched oÄ/off by
with the menu item for the Background lighting.
touching the corresponding light.
› Select the background lighting menu item and set
The brightness level of the lighting can be adjusted
the desired settings.
by holding a fiģe٠on the light. The set brightness
Footwell lighting
level is not saved once the lighting is switched off.
Applies to vehicles that do not have the background
If a door remains open and the ignition is switch-
lighting.
ed off, the lights will turn off automatically after 10
› In the Infotainment system, select the menu
minutes.
Interior .
› By moving your fiÄ£eÙ sideways, choose the screen
with the interior lighting menu item.
Lighting, windscreen wipers and washers › Interior ambient light
53
› Select the menu item for the interior lighting and
Setting the colour for the selection options
adjust the brightness level and color using the slid-
er.
Interior ambient light
Usage
The ambient lighting ensures a comfortable atmos-
phere in the vehicle interior.
The lighting only works when the dipped or parking
A
Tab for adjusting the lighting colour
lights are on.
B
Option for uniform illumination colour
The lighting is also switched on automatically after
▶ The colour is set using the slider E .
opening the door.
C
Option for two-colour lighting
When the vehicle is locked, the lighting bÙieĔû turns
▶ Use the slider bar E to set the colour for the
red. When the vehicle is unlocked, the lighting bÙieĔû
dash panel and door area.
turns green. When one of the doors is opened, the
respective door light is illuminated in red to indicate
▶ Use the slider bar F to set the colour for the
that the door is open.
footwell.
D
Option for two-colour lighting
▶ The colour for the dash panel and door area is
Settings
replaced with the colour for the footwell.
The ambient lighting is set in the Infotainment sys-
E
Slider for adjusting the illumination colour
tem, in the following menu
F
Slider for adjusting the illumination colour
Pre-selection options for background lighting
›
Choose the preset option
› Select the tab for setting the lighting colour.
› Choose whether to set a uniform lighting colour, if
necessary, a diffeÙeÄt colour for the dash panel and
door area and a diffeÙeÄt colour for the footwell.
› Set the desired lighting colour using the sliders.
Setting the brightness level for the selection op-
tions
A
Factory-set pre-selection options
▶ Only the general brightness level of the light-
ing is adjustable.
B
User-selectable pre-selection option
▶ The lighting colour can be adjusted together
for the dash panel and door area, as well as in-
dependently for the footwell.
▶ The brightness level for the lighting can be set
independently for the control panel, central
A
Tab for setting the brightness level
console and door area, as well as the footwell.
B
Setting the brightness level for the centre con-
C
Automatic selection option
sole
▶ The colour and the brightness will change au-
C
Setting the brightness level for the control panel
tomatically depending on the selected driving
area
mode.
D
Setting the brightness level for the footwell
D
Turn off the lights
E
Setting the brightness level for the door area
E
Settings for the general brightness level
› Choose the preset option
F
Setting the colours and the brightness level for
› Select the tab for setting the brightness level.
the pre-selection option
54
Lighting, windscreen wipers and washers › Windscreen wipers and washers
› Select the area for which the brightness level
Wipe and wash the rear window
should be set.
› Set the desired brightness level using the slider.
Windscreen wipers and washers
Operating conditions
✓ Engine compartment Ĕap closed
✓ Boot lid closed
✓ Ignition on
Spring-loaded position:
▶ Washing and wiping the windscreen
Operation
▶ Cleaning the rear view camera
WARNING
Wiping
Risk of an accident!
Switching off
At low temperatures, windscreen washer Ĕuid can
freeze on the windscreen and restrict visibility.
Automatic rear window wiping
▶ Only use the windscreen washer when the wind-
If the windscreen wiping is performed without inter-
screen is warm.
ruption, then the automatic regular intermittent wip-
Wipe and wash the windscreen
ing of the rear window takes place.
When the windscreen wipers are switched on, the
rear window is automatically wiped when the re-
verse gear is engaged.
Settings
Activating/deactivating automatic wiping
The functions for automatic rear window wiping and
automatic wiping in the rain can be activated or de-
activated as in the Infotainment system.
Fast wiping
› The menu
Outside .
Slow wiping
› By moving your fiÄ£eÙ sideways, choose the screen
with the menu item Mirrors and wipers .
Depending upon vehicle equipment:
›
Select Mirrors and wipers .
▶ Intermittent wiping
›
Activate or deactivate the functions.
▶ Automatic wiping controlled by the rain sensor
Switching off
RefilliÄg windscreen washer Ĕuid
Tip-wiping (spring-loaded position)
A
Setting the wiping speed for the position
WARNING
Risk of an accident!
Washing and wiping (spring-loaded position)
▶ Use windscreen washer Ĕuid that is suitable for the
Depending on the vehicle equipment, the wind-
weather conditions.
screen washer nozzles of the windscreen can be
NOTICE
heated automatically.
Risk of damage to the windscreen washer system!
Clean headlights
▶ When ÙefilliÄ£ the washer Ĕuid, do not remove the
strainer from the neck of the container.
When the headlights are switched on, they are
cleaned the fiÙst time and after every tenth wash of
NOTICE
the windscreen. Setting the spray interval can be
Risk of damage to the headlights!
carried out by a specialist garage.
▶ Only use washer Ĕuid that does not attack polycar-
bonates.
Lighting, windscreen wipers and washers › Windscreen wipers and washers
55
NOTICE
› Within 10 seconds,
Risk of damage to engine compartment compo-
press the control lever
nents!
down and hold for
▶ Close the container after ÙefilliÄ£ the windscreen
about 2 seconds.
washer Ĕuid.
The windscreen washer tank is located in the engine
compartment » page 12.
The container can hold a volume of 3 litres and 4.7
litres for vehicles with a headlight cleaning system.
Set the windscreen wiper arms into the folding po-
sition - using the Infotainment system
›
The menu
Outside .
› By moving your fiÄ£eÙ sideways, choose the screen
with the menu item Mirrors and wipers .
› Select Mirrors and wipers and then select the service po-
sition of the windscreen wiper arms.
After switching off the ignition, a menu is dis-
played on the Infotainment screen, showing where
the windscreen wiper arms can be set to folding po-
Sealing cap of the tank
sition.
› Open the engine compartment lid » page 161.
Replace the windscreen wiper blade
› Gently open the top of the sealing cap.
› Top up the windscreen washer Ĕuid.
CAUTION
Risk of accident!
› Close the sealing cap of the tank.
▶
Change the windscreen wiper blades once or twice
a year.
Troubleshooting
› Fold the windscreen wiper arm away from the
windscreen.
Windscreen washer Ĕuid level too low
illuminates together with
› Press the catch and re-
move the wiper blade.
› Insert the new wiper
› Top up the windscreen washer Ĕuid.
blade until it clicks into
Frozen windscreen wipers
place.
› Carefully remove frozen windscreen wipers from
› Fold the windscreen
the windscreen before switching on the ignition
wiper arm back onto
and free them from snow and ice.
the windscreen.
› Turn on the ignition
and push the control
Folding down windscreen wiper arms and
lever down.
replacing windscreen wiper blades
For folding down the windscreen wiper from the
Cap for refilliÄg the windscreen washer Ĕuid
screen you must fiÙst adjust the wiper arms to the
folded position.
NOTICE
Risk of damage to the windscreen wipers and the
engine compartment lid!
▶ Close the bonnet before lowering the wiper arms
from the window.
▶ Do not turn on the ignition when the windscreen
wiper arms are folded away.
Set the windscreen wiper arms into the folding po-
sition - using the operating lever
› Switch the ignition on and off again.
56
Heating and air conditioning system › Climatronic automatic air conditioning system
When the Air Care function surface turns green, this
Heating and air conditioning
indicates that the function has been switched on. Air
system
Care is displayed in the status bar.
When the Air Care function surface turns white, this
Climatronic automatic air conditioning
indicates that the function has been switched on. Air
system
Care is displayed in the status bar.
What you should be mindful of
After the function is switched off, the function
surface Air Care lights up green for a certain time.
▶ We recommend keeping the internal temperature
at most 5 °C lower than the external temperature.
▶ We recommend switching the cooling system off
Operating conditions for the cooling system
about 10 minutes before the end of the journey to
prevent odour formation.
✓ Outside temperature above 2 ° C
▶ Annual disinfection of the air conditioning is rec-
✓ Running engine
ommended.
✓ Fan switched on
WARNING
Danger of misting!
Operation
▶ Always keep the fan on.
Menu for operating the air conditioning
WARNING
Risk of accident!
› Press under Infotainment.
In recirculation mode, there is no fresh air supply
Or:
from the outside. This can result in loss of driver at-
› Tap
in the lower status bar of the infotain-
tention and fogging up of windows.
ment screen.
▶ Keep the recirculation mode switched on for a
short time only.
The following menu is displayed:
Display smart air conditioning with pre-deter-
mined pre-set options
Functionality
Show classic settings for the air conditioning
Smart and classic air conditioning
Air Care
Smart air conditioning is an automatic mode with
Further settings for air conditioning
preset selection options.
After it is switched on, the air conditioning is
The classic air conditioning system enables the indi-
started according to the settings, before it is switch-
vidual functions to be set.
ed off.
Automatic mode
Automatic mode keeps the temperature constant
Settings
and prevents the windows from misting.
Set smart air conditioning
Cooling system
› Press under the Infotainment and tap
in the
When the cooling system is switched on, the tem-
perature and humidity in the vehicle will drop.
Infotainment screen.
Or:
Switching on the cooling system prevents the win-
dows from misting up.
› Tap
in the lower status bar of the infotain-
ment screen.
Recirculated air mode
The recirculation mode prevents contaminated out-
Depending on the equipment, a menu with a number
side air getting into the interior of the vehicle.
of the following functions is displayed:
Air Care
Switch air conditioning on or off
The Air Care function reduces the penetration of
Front
Show the front settings
pollutants into the vehicle interior. At the same time,
Rear
Show the rear settings
the air is both circulated and cleaned.
Preselect option for ventilation/defrosting
of windscreen
For proper operation, the doors and windows must
Preselect option for the Ĕoõ of warm air in-
be closed.
to the footwell
The function is started/switched off by tapping on
Preselect option for the Ĕoõ of warm air in
the function surface
Air Care in the operating
the hand area and switching on the steering
menu of the air conditioning system.
wheel heating
Heating and air conditioning system › Climatronic automatic air conditioning system
57
Preselect option for the Ĕoõ of cold air into
Switch recirculated air mode oÄ/off
the footwell
Switch the cooling system oÄ/off
Preselect option for the Ĕoõ of external air
into the interior
Switch the seat heating or ventilation
Switch maintenance of the interior tempera-
oÄ/off » page 60, Operation
ture oÄ/off according to the temperature
Lock the increase in the heating output of the
setting for the driver's side
rear seat heating and set the rear tempera-
Switch the seat heating or ventilation
ture » page 60, Settings
oÄ/off » page 60, Operation
The function is displayed after tapping the func-
Decrease the temperature
tion surface C .
Increase temperature
Decrease the temperature
The selected preset option is activated for a limited
period of time.
Increase temperature
To start the preset option, certain conditions
The temperature can also be set using two fiÄ-
must be met due to the condition of the vehicle.
£eÙs in the progress bar under the temperature set-
These conditions can neither be iÄĔueÄed nor de-
ting area.
tected.
The rear temperature can also be set on the dis-
When switching off the preselect option the
play in the centre console at the rear.
steering wheel heating is also switched off. This also
With a temperature setting outside of the number
applies to the situation where the steering wheel
range, one of the following icons will be displayed in
heating was switched on manually before starting
the Infotainment screen:
this preselect option.
LO Maximum cooling power
Set classic air conditioning
HI
Maximum heating power
› Press under the Infotainment and tap
in the
Further Climatronic settings
Infotainment screen.
›
Tap the functional area in the operating menu for
Or:
the air conditioning.
› Tap
in the lower status bar of the infotain-
The following menu is displayed:
ment screen.
▶ Automatic air recirculation - Automatic air circulation mode
The following menu is displayed:
oÄ/off
Also included depending on vehicle equipment:
▶ Automatic supplementary heater - Switch fast interior heating
oÄ/off
▶ Automatic windscreen heating - Switch oÄ/off the automatic
windscreen heating » page 59, Settings
▶ Switching oÄ/off the automatic start of seat heat-
ing and ventilation as well as the steering wheel
heating when the engine is started (depending on
the interior temperature)
A
Show the front settings
Consumption-friendly operation of the Climatronic
B
Set the direction of the air outlet
If one of the seats is not occupied, the Climatronic
C
Show the rear settings
adjusts the air temperature accordingly to reduce
D
Switch on automatic mode and set the operat-
energy consumption.
ing power
Eco is displayed in the infotainment screen.
E
Set the blower speed
When the air conditioner is operating, the engine
F
Display menu, overview of the currently selec-
idle speed may increase automatically.
ted functions
Switch Climatronic oÄ/off
Troubleshooting
Switching the windscreen heater
oÄ/off » page 59, Operation
Water under the vehicle
When the cooling system is switched on, water can
Switch maintenance of the interior temperature
drip off the air conditioning system. This is not a leak.
oÄ/off according to the temperature setting for
the driver's side
58
Heating and air conditioning system › Auxiliary heating and ventilation
Fogging
is switched on when the vehicle is not being
› Switch on automatic mode.
charged » page 63, Settings.
Or:
› Increase the blower speed, switch on the cooling
Operation
system, and set the air distribution to the wind-
screen.
Switch oÄ/off with the radio remote control
› Hold down the corresponding key.
Automatic sõitch-off of the cooling system
If the coolant temperature is too high, the cooling
A
Indicator light
system may switch off automatically. This ensures
B
Antenna
suffiieÄt engine cooling.
Switching off
Switching on
Auxiliary heating and ventilation
Usage
The auxiliary heater heats the vehicle interior and the
engine.
Hold the radio remote control with the antenna
The auxiliary ventilation makes it possible to supply
facing upwards.
fresh air to the vehicle interior when the engine is
switched off. As a result, the interior temperature is
NOTICE
lowered, e.g. when the vehicle is parked in the sun.
▶ Protect the remote control from moisture, strong
vibrations and direct sunlight.
Display of the radio remote control indicator light
What you should be mindful of
▶ Lit up green for 2 seconds - switch on
DANGER
▶ Lit up red for 2 seconds - switch off
Risk of poisoning!
Range of the radio remote control
▶ The auxiliary heater must not be operated in en-
The range of the wireless remote control is a few
closed spaces.
hundred meters when the battery is full. For exam-
DANGER
ple, obstacles or weather conditions can reduce the
Risk of fiÙe!
range.
▶ Switch off the auxiliary heater before refuelling.
Warning light display in the instrument cluster.
▶ The exhaust pipe for the auxiliary heater is located
Lights up when the auxiliary heater is switched on
on the underside of the vehicle. Therefore, do not
from the isolation box.
stop the vehicle in places where the exhaust gases
could come into contact with easily Ĕammable ma-
terials, e.g. dry grass, spilled fuel etc.
Set automatic switching on
› In the Infotainment, tap
Functionality
› Tap on
The interior is heated or ventilated according to the
› Select the preset time for the departure time and
temperature that is set in the e-Manager
tap
menu » page 63, Settings.
› Set the departure time, the day(s) of the week and
activate the interior cooling/heating.
The system uses fuel from the fuel tank and electri-
cal energy from the high-voltage battery for heating.
› Activate the preset time.
› Set the desired temperature and activate the auxil-
iary heating.
Operating conditions
If the vehicle is not being charged, the function
for using the energy from the high-voltage battery
✓ The charge state of the 12-volt vehicle battery is
for interior cooling / heating must be switched on in
suffiieÄt.
order to automatically switch on the auxiliary heat-
✓ The fuel supply is suffiieÄt, the instrument clus-
ing » page 63, Settings.
ter does not light up
Further settings are made in the E-Manager
✓ The function for using the energy from the high-
menu » page 63, Settings.
voltage battery for cooling / heating the interior
Heating and air conditioning system › Heated windscreen
59
The auxiliary heating is also set in the ŠKODA
› Use a thin screwdriver
Connect application » page 119, Functionality.
to remove the cover in
the marked area.
› Open the cover and
Troubleshooting
push it out.
Smoke in the engine compartment
In the engine compartment, smoke and odours may
form during the operation of the auxiliary heater.
This is not a defect.
Running the auxiliary heater after stopping the en-
› Use a screwdriver to
gine
loosen the battery in
After switching off the system, the coolant pump
the marked area.
and the auxiliary heating will continue running a little
› Replace the battery.
while longer in order to burn the remaining fuel in
› Insert the cover and
the heating.
push it until it audibly
Indicator light in the radio remote control
locks into place.
▶ Flashes green in a slow sequence - the switch-on
signal was not received
▶ Flashes red in a slow sequence - the sõith-off sig-
nal was not received
▶ Flashes green in an irregular pattern - the parking
Heated windscreen
heater is locked, e.g. because the fuel tank is al-
most empty or there is an error
Usage
› Check the level of fuel.
Windscreen heating is used for defrosting or venti-
› If the fuel quantity is OK, seek the help of a spe-
lating the windscreen.
cialist company.
▶ Lights up orange fiÙst, then green/red - the battery
is weak, the oÄ/off signal has been received
Requirements
▶ Lights up orange fiÙst, then Ĕashes green/red - the
✓ Running engine
battery is weak, the oÄ/off signal has not been re-
✓ Outside temperature approximately below 35 ° C
ceived.
▶ Flashing orange - the battery is nearly discharged,
the oÄ/off signal has not been received
Operation
▶ Not lit up - the battery is discharged, the oÄ/off
signal has not been received
Heated rear window
› Press the button under the Infotainment.
› Replace the battery.
Heated windscreen
›
Press the button under the Infotainment.
Change the battery in the remote control
› Tap on function surface
/
Front
in the In-
fotainment screen.
WARNING
Risk of death!
Windscreen heating switches off automatically after
If the battery is swallowed, serious or even fatal inju-
some time.
ries can result from burns in the digestive tract.
If the engine is switched off when the heating is on
▶ Always keep children away from the radio remote
and turned back on again within about 10 minutes,
control and batteries.
the heating is continued.
▶ If the battery is swallowed, seek medical help im-
mediately.
Mode for ventilation/defrosting of windscreen
› Press the button under the Infotainment.
Settings
Automatic heated windscreen
The heated windscreen switches on automatically if
the windscreen mists up.
60
Heating and air conditioning system › Seat heating and ventilation
› Press the button below the Infotainment
Models with seat ventilation
and tap the Infotainment screen.
› Tap the or function surface in the Infotainment
› Select the menu item for automatic windscreen
screen to turn on front seat heating.
heating.
A menu is displayed for operating the front seat
heater and ventilation.
› Adjust the heating output/ventilation level.
Troubleshooting
›
Press the or button in the rear centre console
The indicator light in the button or below the but-
to switch on the rear seat heating.
ton Ĕashes
The heating is switched on with maximum heating
The heating does not work as the battery charging
level of the 12 volt vehicle battery is too low.
output. By repeatedly pressing the button, the
heating output is reduced until it is switched off.
Display heating output/ventilation level in the but-
Seat heating and ventilation
ton
Seat heating switched on
What you should be mindful of
Seat ventilation switched on
WARNING
If the engine is switched off with the heating/ventila-
Risk of burns!
tion switched on and then started again within ap-
▶ Do not switch on the seat heater for persons with
proximately 10 minutes, the heating/ventilation will
limited perception of pain or temperature.
continue according to the setting before the engine
NOTICE
was switched off.
Risk of seat damage!
▶ Do not kneel on the seats or otherwise apply con-
centrated pressure to them.
Settings
▶ Do not turn on the heater in the following situa-
Lock increases in heat output for the rear seat
tions:
heater
▶ The seat is not occupied.
› Press the button under the Infotainment sys-
▶ There are objects on the seat, such as a child
tem
Rear Tap on
/
in the Infotain-
seat.
ment screen.
▶ There are additional seat covers or protective
When the function is switched on, the heating out-
covers on the seat.
put can only be turned down.
The function also blocks the possibility of setting
Requirements
the temperature in the display in the rear centre con-
sole.
✓ Running engine
Heated steering wheel
Operation
Requirements
Depending on the equipment, the front seats can be
heated or heated and ventilated. The outer rear seats
✓ Running engine
can only be heated.
Models without seat ventilation
Operation
› Tap the or function surface in the Infotainment
screen to turn on front seat heating.
› Press the button on the multifunction steering
› Press the or button in the rear centre console
wheel.
to switch on the rear seat heating.
The heating is switched on with maximum heating
The heating is switched on with maximum heating
output. By repeatedly pressing the button, the heat-
output. By repeatedly pressing the button, the heat-
ing output is reduced until it is switched off.
ing output is reduced until it is switched off.
By holding down the button on the multifunc-
The output level of the heating is indicated by the
tion steering wheel, the heating can be switched off
number of illuminated indicator lights in the button
or switched on at the level of the heating output that
or in the Infotainment screen.
was set before the heating was switched off.
Driver information system › Digital instrument cluster
61
Driver information system
Operation
Overview of the buttons/dials on the multifunction
Digital instrument cluster
steering wheel
Overview
A
Rotate - Switch be-
tween menu items /
Overview of instrument cluster
set values / change
map scale manually
Press - CoÄfiÙm
menu item
Turn and press -
Switch on automatic
change of map scale
Change variant of
the display presentation / Show menu items of
the submenu on the left side of the display
Change variant of the display presentation /
A
Bar with indicator lights
Show menu items of the submenu on the right
B
Charge level indicator for high-voltage battery
side of the display
C
Fuel gauge
Show menu with selected information in the dis-
play
D
Display
› To display the menu on the right side of the display,
E
Display area with selected information for the
press the setting wheel A.
driver
› To display the menu on the left side of the display,
F
Central display area
press the control wheel A twice.
NOTICE
› To switch between information, turn the setting
Risk of serious damage to the engine and the ex-
wheel A.
haust system!
› To oÄfiÙm the information selection, press the set-
▶ Never run the fuel tank completely empty!
ting wheel A.
Power display
Certain information contains a submenu.
› To display the submenu, press the or key.
› To switch between menu items on the submenu,
turn the control wheel A .
The option to switch between information is indi-
cated by arrows. This is only possible for a short
time.
Settings
Setting the language
The language is set in the Infotainment in menu
Setting the time
The time is set in the Infotainment in menu
A
Energy recovery
The energy generated during braking is stored in
Setting the brightness of the instrument cluster
the high-voltage battery during recuperation.
lighting
The brightness is adjusted automatically according
B
Power availability of the electric motor
to the given lighting conditions.
C
Internal combustion engine speed
The manual brightness adjustment is carried out as
Boost
Status of full acceleration using the internal
follows when the dipped beam is switched on.
combustion engine and the electric motor.
› In the Infotainment system, select the menu
Interior Ambient lighting .
62
Driver information system › Head-Up display
› Adjust the setting.
In the displayed menu, the following menu items can
be set:
Set the variant of the display
› Press the button or on the multifunction steer-
▶ Activation/deactivation
ing wheel to change the variant of the display pre-
▶ Position
sentation.
▶ Brightness
▶ Colour scheme
Select displayed variants
▶ Selection of projected information
The position can also be set by turning the dial A
on the multifunction steering wheel.
Depending upon vehicle equipment:
A
Classic display
B
Navigation announcements
Driving data
C
Driver Assist
Overview
D
Basic display
The driving data display works with the ignition
E
Sporty display (depending on equipment)
switched on.
In the instrument cluster display
Depending on the equipment, the display of the in-
Head-Up display
strument cluster shows information such as speed,
fuel consumption, range, etc.
Functionality
In Infotainment
The head-up display projects selected information
The following information is displayed in the Info-
onto the windscreen into the driver's field of vision.
tainment:
Distance travelled
Driving time
Average speed
Average fuel consumption
Range
Restriction
Memory
The system saves the driving data in the following
The function may, for example, be restricted or un-
memories:
available due to strong sunlight.
Since start
Sunglasses with polarisation filteÙs can negatively
▶ Driving data from the time of switching on the ig-
affet the visual perception of the display.
nition until the ignition is switched off again is stor-
ed in the memory. If the journey is interrupted for
more than 2 hours, the memory will be reset.
Settings
Long-term
› The menu
Interior .
▶ The driving data of all trips up to a total of 99
hours and 59 minutes driving time or 9999 km
› By moving your fiÄ£eÙ sideways, choose the screen
driving distance is stored in the memory. If one of
with the menu item Head-Up display .
the listed values is exceeded, the memory is reset.
› Select Head-Up display .
Driver information system › e-Manager
63
Since refuel
› Reset the associated memory by pressing the but-
▶ Driving data from the time the fuel tank was last
ton
filled is stored in the memory. The memory is reset
the next time the tank is filled.
Settings
Setting units
Operation
The units are set in the Infotainment in menu
Display driving data in the display of the instru-
ment cluster via the multi-functional steering
wheel
e-Manager
› To display the menu on
the right side of the
Settings
display, press the con-
trol wheel A .
Display main menu
› To display the menu on
› Turn on the ignition.
the left side of the dis-
› In infotainment select menu
play, press the control
The following menu is displayed:
wheel A twice.
› To switch between in-
formation, turn the
control wheel A .
Displaying driving data in the infotainment system
The driving data is displayed in the infotainment sys-
tem in the menu
Select memory for driving data in the display of
the instrument cluster via the multifunction steer-
A
Set the departure time and day of the week
ing wheel and reset it
B
Set functions
› To set the memory for
the displayed driving
C
When the heating is running, the windows are
data on the right, press
displayed in red
button . Turn the dial
When ventilation is running, the windows are
A to select the corre-
displayed in blue
sponding memory or
D
Charging status of the high-voltage battery
press the dial to con-
E
Immediate start / cancellation of the charging
fiÙm the memory.
process
› To select the memory
for the displayed driv-
F
Activation / deactivation of the reduced charg-
ing data on the left,
ing current
press button . Turn the dial A to select the corre-
G
Lower battery charging limit
sponding memory or press the dial to oÄfiÙm the
H
Setting the desired interior temperature
memory.
I
Activate/deactivate the stand-by heating and
› To re-set the memory for the displayed driving da-
ventilation » page 58, Usage (depending on fea-
ta, press button or . Turn the dial A to select
tures).
reset corresponding memory or press the dial to
oÄfiÙm the re-set.
Setting the departure time
› Tap on
Selecting the memory in the infotainment system
The memory selection is made by touching the cor-
› Select one of the pre-set options for setting the
responding tab in the infotainment screen in the fol-
departure time.
lowing menu
In the displayed pre-selection option, you can use
the functional surface to set or switch on follow-
Resetting the memory in the infotainment system
ing menu items:
The memory is reset in Infotainment as follows:
▶ Departure time
Interior Instrument cluster
▶ Weekday(s)
64
Driver information system › e-Display
▶
Repeat for the selected weekday(s)
Energy Ĕoõ display
▶ Interior cooling / heating
▶ Charging
▶ Low taÙiff
▶ Time lapse for low taÙiff
› Activate/deactivate the selected preselection op-
tion.
Setting the interior cooling / heating
› Tap on .
In the menu that is displayed, the following menu
items can be set or switched on:
▶ Desired interior temperature.
▶ Automatic front and rear window heating (depend-
ing on equipment).
▶ Choice of a front seat that can be heated.
More settings
› Tap on
In the menu that is displayed, the following menu
items can be set or switched on:
▶ Lower battery charging limit
▶ Start of interior cooling / heating when unlocking
the vehicle
▶ Use of the energy from the high-voltage battery
for interior cooling/heating
If the function is not switched on, the interior cool-
ing/heating is started only when charging.
e-Display
Overview
e-Range monitor
Electric motor active
Combustion engine active
Energy recovery (recuperation)
Electric motor and combustion engine active
1
The electric motor is active.
2
The vehicle is driven by the electric motor, the
high-voltage battery discharges.
The e-range monitor displays the electrical range as
3
High-voltage battery
well as the effet of switched-on consumers of the
energy consumption. By tapping on the function sur-
4
The combustion engine is active.
face Potential a list of other consumers is displayed.
5
The vehicle is driven by the combustion engine,
and the state of charge of the high-voltage bat-
Zero Emission
The Zero Emission view shows the total distance
tery is maintained.
covered from the start of the journey as well as the
6
The high-voltage battery is charged by energy re-
proportion of the distance travelled using electric
cuperation.
drive.
7
At full acceleration, the electric motor and the
combustion engine are active, and the high-volt-
age battery discharges.
Driver information system › Vehicle status
65
The energy Ĕoõ is displayed using coloured repre-
The warning messages will continue to be dis-
sentations.
played until the malfunctions have been remedied.
After the fiÙst display of the message, only the indi-
▶ Green - energy Ĕoõ from the high-voltage battery
cator lights
(Hazard) or
(Warning) are dis-
(operated by electric motor) or to the high voltage
played.
battery (battery charging).
▶ Orange - energy Ĕoõ from the combustion engine
to the driven axle (operated by combustion en-
Button SET
gine).
▶ Blue - energy recovery through idling thrust or re-
Overview
cuperation.
The button allows quick access to the settings of
the following vehicle systems (depending on the ve-
Operation
hicle fittiģs):
▶ Switch off ASR traction control » page 137,
Display in Infotainment
Overview.
› Turn on the ignition.
▶ Switch on the ESC Sport stabilisation pro-
› In the Infotainment, tap
gramme » page 137, Overview.
› Select the desired e-display by tapping the func-
▶
Interior monitoring » page 27, Settings.
tional surface or
▶ Tyre pressure monitor » page 176, Functionality.
▶ Access to selection and settings for driver assis-
Vehicle status
tance systems
▶ Access to other vehicle settings
Display
The vehicle status is displayed in the infotainment
system in the menu
A
Vehicle areas displayed in colour indicate associ-
ated warnings
B
Service appointments and vehicle ideÄtifiatioÄ
number (VIN)
C
Tyre pressure monitor
D
Information regarding engine oil level
E
Warning messages regarding the vehicle condi-
tion and their quantity
F
Fuel range and electrical range
Functionality
In the event of a system fault, messages regarding
the fault in question are displayed on the instrument
cluster display when the ignition is switched on.
Messages in relation to faults can also be displayed in
the Infotainment.
66
Infotainment Bolero › Infotainment overview
▶ Volume adjustment of individual Infotainment
Infotainment Bolero
functions
Infotainment overview
The volume can be adjusted on e.g. one of the fol-
lowing menu items:
▶ Volume adjustment of voice commands
▶ Setting the maximum volume when Infotainment
is turned on
▶ Speed-dependent volume setting
▶ Setting the Infotainment to mute with the park-
ing aid switched on
Depending on the equipment, the following ad-
vanced sound settings can be set
▶ Setting space optimisation
▶ Setting the audio pÙofiles according to genre
▶ Adjusting the subwoofer volume
A
Touchscreen
CoÄfiguratioÄ wizard
B
Sensor fields
The oÄfi£uÙatioÄ wizard helps to set certain Info-
▶
- Preferred menus
tainment functions.
▶
- All menus
The oÄfi£uÙatioÄ wizard is automatically displayed if
C
Progress bar for volume adjustment
the ignition is switched on and if there are at least
two menu items that have not been set after switch-
Condition-based:
ing on the Infotainment.
▶ Infotainment switched off
› To switch off the automatic display, when the
▶ Tap: Turn on Infotainment
oÄfi£uÙatioÄ wizard is displayed tap Don't show again .
▶ Infotainment switched on
› For manual display, tap
Configuration wizard .
▶ Tap: Switch sound off/oÄ
Set up menu HOME
▶ Hold: Switch off Infotainment
› To display another page of the HOME menu, press
the screen and drag to the left or right.
Add a preferred menu
System
›
To display the editing mode hold a fiģe٠on the
Restriction
screen.
›
Tap a free space with functional areas.
For safety reasons, operation of some Infotainment
› Select a menu with the desired dimension of the
functions while driving is not possible or is restricted.
functional surface.
The Infotainment system indicates this by means of
The Infotainment only offeÙs font sizes that corre-
a message in the screen.
spond in dimension to the fields with functional
areas that are currently free.
Basic settings
› To end edit mode, tap .
Remove the preferred menu
Setting basic functions
› To display edit mode, press and hold the screen
The following Infotainment functions are set in the
with one fiÄ£eÙ.
menu:
› Tap on the desired menu.
▶ Time and date
› To end edit mode, tap .
▶ Language
Add/remove one side of the HOME menu
▶ Units
› To display edit mode, press and hold the screen
▶ Restore factory settings
with one fiÄ£eÙ.
Sound settings
› Tap on
The Infotainment sound is set in the menu
› To add another page, tap
The following menu items can be set:
The maximum number of pages is 4.
▶ Setting the equalizer
› Tap to remove a page.
▶ Adjusting the volume ratio
The minimum number of pages is 2.
Infotainment Bolero › Screen
67
› Tap to return to the edit mode.
C
Display/close the submenu window
Set up menu MENU
D
Display of the Infotainment control centre
The position of the functional surfaces in the MENU
menu can be customized as follows:
Operation
› Press and hold the desired functional surface until
it is free.
NOTICE
› Move the functional surface to a diffeÙeÄt position.
Danger of screen damage!
Factory settings
▶ The Infotainment screen is operated by touching it
lightly with your fiÄger.
Resetting the Infotainment to factory defaults re-
stores all factory defaults.
In principle, operation by touch is identical to the op-
› Turn on the ignition and switch on Infotainment.
eration of a mobile phone.
› Tap on
The following operating modes are speifi to the In-
› Reset to factory settings select and oÄfiÙm the reset.
fotainment system.
To check the factory reset was successful, we
Tap
recommend that you check all user accounts have
been deleted.
▶ Select function or
menu item
Troubleshooting
Infotainment not responding
If the infotainment does not respond, restart it as
follows:
Hold call
› Hold for longer than 10 s.
▶ Zoom into the map
› Wait for the restart to complete.
System update
We recommend having the system update carried
out by a specialist company.
Dragging up or down with two fiÄgers
The system update ensures optimal function of the
Infotainment system, e.g. compatibility with new
▶ Quickly look through
phones.
the lists
Determine system version
▶ Switch 2D/3D map dis-
› Tap
System information.
play
Screen
Pulling apart with two fiÄgers
Overview
▶ Zoom into the map
A
Status bar
B
Bar with the functional surfaces of the displayed
menu
68
Infotainment Bolero › Infotainment keyboard
Pulling together with two fiÄgers
Infotainment keyboard
▶ Zoom out of the map
Keypad overview
The arrangement of the keyboard characters de-
pends on the set infotainment language.
Depending on the context, the following types are
used in infotainment:
▶ Alphanumeric
Turn two fiÄgers
▶ Numeric
▶ Rotate the map
▶ Keyboard for input
▶ Keyboard for search
Press and hold
▶ Release certain Info-
tainment menus with
the option to move
them to another loca-
Keypad example
tion on the screen
A
Input line
▶ Touch the input line to display function areas
for moving the cursor
Contactless gesture control
Some Infotainment menus can be controlled by hand
▶
Delete characters before the cursor
gestures.
▶ Tap: delete the last entered character
› Gesture control is ach-
▶ Hold: delete all entered characters in se-
ieved by slowly moving
quence
the hand back and
▶ Delete all entered characters
forth approximately 8
B
Entries searched for
cm above the lower
edge of the screen.
▶ Show list of searched entries
Depending on the set-
C
Keypad functional surfaces
ting, a recognized ges-
▶ Change sentence case
ture can be oÄfiÙmed acoustically and animated.
▶
Switch to the language keypad
Displaying operation help
▶
/
Switch to the numeric/character key-
› Tap on
board
▶
/
Switch to other character variants
▶
Show additional keypad languages
Settings
▶ Display the entered password
The following basic screen functions are set in the
▶
/
CoÄfiÙm the characters that have been
menu
Screen:
entered
▶ Image of the screen background
▶ Brightness level of the screen
▶ Switch off the screen
▶ Display the time
▶ CoÄfiÙmatioÄ sounds and animations
Infotainment Bolero › Voice control
69
Numeric keypad
Setting additional keypad languages
› For Settings
, tap Additional keypad languages.
› Select the desired language.
Voice control
Functionality
Voice control principle
Voice control works according to the principle of
Keypad example
dialogue between the user and the Infotainment sys-
A
Input line
tem.
▶ Touch the input line to display function areas
The user says a voice command. The Infotainment
for moving the cursor
system responds or executes the voice command.
▶ Delete characters before the cursor
It is possible to interrupt a dialogue at any time and
▶ Tap: delete the last character
issue a new statement without having to wait for a
▶ Hold: delete all characters
complete response.
B
Keypad functional surfaces
Advanced voice control
CoÄfiÙm the characters that have been entered
The advanced voice control of the vehicle enables an
online search and operation of the vehicle functions.
If context-sensitive, alphanumeric characters can
The advanced voice control understands ĔueÄtlû
be entered by holding a functional surface with a
spoken, complete sentences. You do not need to use
digit.
set commands or phrases.
The advanced voice control can, for example, search
Operation
for special destinations or dictate SMS messages if
the connected telephone makes this possible.
The Infotainment keypad is used to enter characters,
This function allows you to combine the search in
letters and numbers.
the online and offliÄe data of the Infotainment. The
The keypad will be automatically displayed when In-
transition between online and offliÄe search is seam-
fotainment prompts for characters.
less and imperceptible to the user.
Search
When entering characters, corresponding entries are
Operating conditions
searched for.
The entry to be searched for can be entered includ-
✓ Ignition on
ing diacritics.
✓ Infotainment switched on
The keyboard will only provide characters that
Operating conditions for advanced voice control
match the stored entries.
To use the advanced voice control, the following
› To display searched entries tap
conditions must also be met:
The number of searched entries is displayed above
✓ The vehicle supports the function.
the symbol
✓ The vehicle has Infotainment and functions that
can be controlled by the advanced voice control.
Show additional keypad languages
✓ The ŠKODA Connect services are active.
To use the additional keypad languages, the desired
✓ The vehicle is within range of a contractual mo-
languages must be set fiÙst.
bile network, through which the connection to
› To use, repeatedly tap on the keyboard or on the
ŠKODA Connect Services is ensured.
Ĕa£ icon until the desired language keyboard is dis-
✓ The level of protection of personal data is set to
played.
Share my position .
Further character variants
Requirement for recognition of the activation
› Press and hold the character with the other char-
command
acter variant.
✓ Activated menu item
Voice control Active
› Select the desired symbol.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст