Skoda Kamiq (2021 year). Manual in english — page 7
Driver assist systems › Front Assist 133
Operating conditions
✓ There has been a frontal, side and rear collision of
a certain severity.
Front Assist
✓ The impact speed was greater than 10 km/h.
Functionality
✓ The brakes, ESC and other required systems re-
mained functional after the impact.
Front Assist monitors the distance to the vehicle
✓ The accelerator pedal is not pressed.
ahead and points out when the safety distance is ex-
ceeded. In borderline situations, it helps to avoid a
Trailer Stability Assist (TSA)
collision by braking interventions.
TSA helps to stabilize the trailer. As the trailer begins
to lurch, TSA stabilizes the trailer by slowing down
Status display in the instrument cluster display
the individual vehicle wheels.
illuminates - safety distance too small
Operating conditions
✓ The hitch was supplied from the factory or pur-
or
illuminates - warning in case of collision
chased from ŠKODA Genuine Accessories.
✓ The trailer is connected to the trailer socket.
Automatic braking if there is a risk of a collision
✓ ASR activated.
If there is a risk of a collision, the following symbol is
✓ The driving speed is higher than 60 km/h.
illuminated as a warning
or
from the isolation
box. If you do not respond to the warning, the vehi-
cle will slow down.
Settings
At a driving speed of up to 30 km / h, the vehicle is
braked without prior warning.
Deactivating/activating ASR
In Infotainment, in the following menu:
Automatic braking can be stopped by pressing the
accelerator pedal or by a steering intervention.
With automatic braking, the pressure in the brake
Or:
system increases. The brake pedal cannot be operat-
ed by using the pedal as normal.
When deactivated, lights up in the instrument
WARNING
cluster.
Risk of an accident!
goes out on renewed activation.
Front Assist does not respond to crossing or oncom-
ing vehicles.
Deactivating the ASR may be helpful in the following
situations:
▶ Driving with snow chains
Operating conditions
▶ Driving in deep snow or on very loose ground
✓ The parking aid is activated.
▶ Starting up a vehicle that is stuck
✓ The driving speed is higher than 5 km/h.
Troubleshooting
Function restriction
ESC or ASR faulty/deactivated by the system
illuminates
The function may be restricted or unavailable in the
following cases:
› Stop the engine and start again.
▶ About 30 seconds after starting ( lights up in
› If the indicator light does not go out after covering
the instrument cluster)
a short distance, seek the help of a specialist ga-
rage.
▶ When driving around a sharp bend
▶ During an ESC intervention
ABS faulty
illuminates
Settings
› You may continue driving, exercising appro-
priate caution. Seek the help of a specialist garage.
Automatic activation
Front Assist is automatically activated when the igni-
Brake system and anti-lock braking system faulty
tion is switched on.
illuminates together with
› Stop driving! Seek the help of a specialist ga-
rage.
134 Driver assist systems › Pedestrian detection system
Activation/deactivation in the instrument cluster
Risk of collision in a speed range of 30-60 km/h
› Press the button on the multifunction steering
The system warns of a collision hazard fiÙst. If the
wheel.
driver does not respond, the vehicle is automatically
› Select Front Assist .
braked.
Activation/deactivation in Infotainment
In the menu
Operating conditions
Show system deactivation in the display of the in-
✓ Front Assist is deactivated.
strument cluster
✓ The vehicle speed is 5-60 km/h.
illuminates together with
or
Speed limiter
illuminates together with
Functionality
Deactivate Front Assist when handling the vehi-
The speed limiter controls the maximum driving
cle on a truck, a car ferry etc.
speed according to the set speed limit.
If the limit is exceeded when driving downhill, brake
the vehicle with the brake pedal.
Troubleshooting
Status display in the instrument cluster display
Front Assist is not available
illuminates - the cruise control is activated.
illuminates together with
ĔashiÄ£ - the set limit is exceeded
When the regulation starts highlighted and the
Or:
set limit is displayed.
illuminates together with
Operating conditions
› Clean the front radar sensor.
› Stop the engine and start again.
✓ The driving speed is higher than 30 km/h.
› If Front Assist is still unavailable, check the brake
lights on the vehicle or on the attached trailer.
Operation
› If the brake lights are working and Front Assist is
still unavailable, seek the help of a specialist ga-
Variant without cruise control
rage.
There was an unfounded warning or system inter-
vention
› Clean the front radar sensor.
› If the system is not working properly, disable Front
Assist and seek the help of a specialist garage.
Pedestrian detection system
Functionality
A
Activate limiter (control inactive)
Pedestrian recognition helps to prevent a collision
Deactivate limiter
with crossing or lengthwise moving pedestrians by
enabling automatic braking interventions.
Interrupt control (sprung position)
B
Resume control1) / Increase limit
Status display in the instrument cluster display
or
lights up - Danger of collision
C
Start control with current speed / Reduce
limit
Risk of collision in a speed range of 5-30 km/h
The system triggers automatic braking.
1)
If no speed limit is set, the current speed is set as the speed limit.
Driver assist systems › Cruise control system 135
Variant with cruise control
Variant with ACC
A
Activate cruise control (condition for the
subsequent activation of the limiter).
To activate the speed limiter, press button D or
E.
Deactivate limiter
Activate ACC (condition for the subsequent
Interrupt control (sprung position)
activation of the limiter). To activate the limit-
er, press button A .
B
Resume control1) / Increase limit
Resume control 1) / Increase limit in steps of
C
Start control with current speed / Reduce
1 km/h (sprung position)
limit
Stop control (sprung position)
D
Depending on the equipment:
Deactivate the limiter
Switch between cruise control and speed
limiter
Increase limit in steps of 10 km/h
Or:
Decrease limit in steps of 10 km/h
Show menu of assist systems - Possibility of
Start control/Reduce limit in steps of 1 km/h
switching between cruise control and speed lim-
A
Change between ACC and speed limiter (by
iter
switching to cruise control, control is inter-
Switching to cruise control interrupts the con-
rupted)
trol.
E
Show menu of assist systems - Possibility of
Limit exceeded
switching between cruise control and speed lim-
› Fully depress the accelerator.
iter
Control will continue as soon as the vehicle has de-
Switching to cruise control interrupts the con-
celerated to below the set limit.
trol.
Adjusting the speed limit with the buttons B and
Troubleshooting
C
Speed limiter faulty
By pressing in steps of 1 km/h.
illuminates
By holding in steps of 10 km/h.
› Seek the help of a specialist garage.
Cruise control system
Functionality
The cruise control system maintains the set speed
without the accelerator pedal having to be operated.
This, however, is only possible to the extent permit-
ted by the engine output and braking power of the
vehicle.
1)
If no speed limit is set, the current speed is set as the speed limit.
136 Driver assist systems › Adaptive Cruise Control (ACC)
WARNING
Troubleshooting
Risk of the cruise control system starting uninten-
Cruise control system faulty
tionally!
illuminates
▶ Deactivate cruise control after use.
› Seek the help of a specialist garage.
Status display in the instrument cluster display
illuminated - the cruise control system is acti-
vated
Adaptive Cruise Control (ACC)
illuminated - cruise control is active
When cruise control starts, the set speed is
Functionality
displayed.
ACC control
ACC maintains the set speed. When your vehicle ap-
Operating conditions
proaches the vehicle in front, ACC will automatically
start to maintain the set distance to this vehicle.
✓ The driving speed is higher than 20 km/h.
Maintaining the set speed and the distance will here-
inafter be referred to as Control.
Operation
WARNING
ACC does not respond to stationary objects or to
Operating with the lever
crossing or oncoming objects.
ACC is intended primarily for use on motorways.
Speed range
Depending on the equipment, ACC allows a speed
setting in the range of 30-160 or 30-210 km/h.
If control is started at a speed of less than 30 km/h
on vehicles with an automatic transmission, the
speed is automatically increased to 30 km/h or con-
trolled according to the speed of the vehicle ahead.
Distance level
A
Activate cruise control (cruise control deacti-
The distance to the vehicle ahead can be adjusted to
vated)
five diffeÙeÄt levels.
Deactivate cruise control
WARNING
Interrupt control (sprung position)
▶ Maintain a minimum distance in accordance with
B
Resume cruise control1)/Increase speed
the ouÄtÙû-speifi legal regulations.
C
Start control with current speed/Reduce
Automatic stop and start
limit
A vehicle with an automatic transmission can be de-
celerated to a stop using the ACC and start moving
D
Show menu of assist systems - Possibility of
again. In the event of a long stop, a message will ap-
switching between cruise control and speed lim-
pear in the display, indicating that you must operate
iter
the brake pedal.
Accelerate temporarily
› Keep the brake pedal depressed until the vehicle in
› Depress the accelerator pedal.
front starts moving.
Releasing the accelerator pedal will cause the speed
If the brake pedal is not depressed, control is inter-
to drop again to the set speed.
rupted.
Interrupting cruise control
Overtaking
▶ After pressing the brake pedal
If your vehicle changes to the fast lane and no vehi-
▶ After an ESC intervention
cle is detected in front, ACC accelerates up to the
set speed.
Status display in the instrument cluster display
illuminates - ACC is activated
1)
If no speed is set, the current speed is adopted.
Driver assist systems › Adaptive Cruise Control (ACC) 137
Depending on the equipment:
Line A appears in the
illuminates - Control is active
display, indicating the
change in distance.
or
› Use the
switch
to set the desired dis-
illuminates together with
tance level.
- Control is active
When the control starts, the set speed is displayed.
illuminates - ACC does not decelerate suffi-
ieÄtlû
For temporary acceleration
› Depress the brake pedal.
› Depress the accelerator pedal.
The vehicle accelerates and control is temporarily in-
terrupted. Upon releasing the accelerator, control is
Operation
resumed.
Operating with the lever
Interrupting cruise control
▶ After pressing the brake pedal while driving
▶ By operating the clutch pedal for a long time
▶ After an ESC intervention
▶ After deactivation of the ASR
Resuming control
›
If a speed is stored, move the lever to the sprung
position
The vehicle is controlled at the set speed. The set
speed is shown in the instrument cluster display.
Function restriction
Do not use the ACC in the following cases:
Activate ACC (control inactive)
▶ The vehicle is making a sharp turn.
▶ The vehicle is travelling on a sloping road or in ruts.
Start or resume control/Increase speed in
steps of 1 km/h (sprung position)
▶ When the driving lane is too narrow.
▶ The vehicle drives through a construction site.
Stop control (sprung position)
Deactivate ACC
WARNING
▶ Be particularly attentive and alert in the following
Increase speed in steps of 10 km/h
situations.
Reduce speed in steps of 10 km/h
Regulation according to the vehicle in the adjacent
Set distance level
lane
Start control/Reduce speed in steps of 1
If your vehicle is moving faster than the vehicle in
km/h
the next lane on the driver's side, at a speed of more
than 80 km/h, this may cause your vehicle to be con-
Starting control with the current speed
trolled according to that vehicle.
› Tap on
Or:
› If no speed is saved, move the lever to the sprung
position
Set distance level
› Move the
switch to the sprung position
or
138 Driver assist systems › Lane Assist
When cornering
Vehicles with special load or special bodies
A load or superstructure that protrudes outside the
vehicle might not be detected by the ACC.
Settings
Activation / deactivation and setting
In the Infotainment system, in the menu
◼
When cornering, a vehicle in the next lane may enter
▶ Driving programme: - Setting the vehicle acceleration
the detected area. Your vehicle will be controlled ac-
when the ACC is switched on (this setting is
cording to this vehicle.
made for vehicles with driving mode selec-
Narrow or staggered vehicle
tion » page 128)
▶ Last distance selected - Switch oÄ/off the last distance
selected
▶ Distance: - Setting the distance to vehicles in front
Troubleshooting
ACC not available
illuminates together with
or
ACC detects a narrow or staggered vehicle only
illuminates together with
when it is in the area covered by the radar.
Lane change by another vehicle
› Stop the engine and start again.
› If ACC is still unavailable, check the brake lights on
the vehicle or on the attached trailer.
› If the brake lights are working and ACC is still un-
available, seek the help of a specialist garage.
Lane Assist
Usage
Lane Assist helps to keep the vehicle within the lane.
A vehicle that changes to the lane a short distance
It is based on the boundaries of a lane. These may in-
away may not be recognized by the ACC in time.
clude lane markings, road edges or objects such as
curbs or possibly tÙaffi cones.
Stationary vehicle
The system is intended primarily for use on high-
ways.
Functionality
As the vehicle approaches a lane marking, the sys-
tem executes a steering movement in the opposite
direction from the lane marking. The steering inter-
vention can be overridden manually.
No system intervention occurs when changing lane
If a vehicle in front turns and there is a stationary ve-
with the turn signal on.
hicle in front of this vehicle, the ACC must not re-
spond to the stationary vehicle.
Driver assist systems › Lane change assist system Side Assist 139
Status display in the instrument cluster display
▶ Always keep your hands on the steering wheel and
lights up - System is activated and ready to
be prepared to override the steering intervention.
intervene
lights up - System is activated and ready to
Settings
intervene
lights up - System intervenes
Automatic activation
Lane Assist is always automatically activated when
the ignition is switched on.
lights up - System intervenes
Activation/deactivation in the instrument cluster
Display
› Press the button on the multifunction steering
Display example in black and white display.
wheel.
› Select Lane Assist .
Lane boundary highligh-
ted on the right: system
Activation/deactivation in Infotainment
intervenes on the right
In the menu
when approaching the
lane marking.
Troubleshooting
In the coloured display,
the lines are highlighted
Message regarding system unavailability
in colour.
› Clean the windscreen in the sensor area.
› Stop the engine and restart again after a short
time.
Warning through steering wheel vibrations
› If the system is still not available, seek the help of a
The steering wheel vibrations are triggered in the
specialist garage.
following situations:
▶ The vehicle crosses the boundary line without the
indicator light switched on.
Lane change assist system Side Assist
▶ The system is not able to keep the vehicle within
the lane.
Usage
› Correct the steering movement in the event of vi-
The system uses optical signals in the exterior mirror
brations.
to alert the driver to vehicles that could be danger-
ous when changing lanes.
Operating conditions
Functionality
✓ The driving speed is higher than 60 km/h.
✓ The lane markings are clearly visible.
The system monitors the area both beside and be-
hind the vehicle.
The system warns of an approaching vehicle through
Function restriction
the indicator light in the exterior mirror cover on
The system function may be restricted in the follow-
the vehicle side, where the vehicle is recognized.
ing cases:
Driving situations in which a system warning oc-
▶ The field of view of the sensor is limited by a dirty
curs
screen or an obstacle or a preceding vehicle.
▶ If the weather conditions are unfavourable.
▶ The vehicle is making a sharp turn.
▶ The vehicle is travelling on a sloping road or in ruts.
▶ When the driving lane is too narrow.
▶ The vehicle drives through a construction site.
WARNING
Danger of incorrect steering intervention!
Certain objects or markings on the road may be erro-
neously recognized as lane markings.
140 Driver assist systems › TÙaffi sign recognition
Your vehicle is being overtaken by vehicle A . The
Troubleshooting
faster vehicle A approaches, the sooner the warning
Message regarding system unavailability
is given by the indicator light.
› Stop the engine and start again.
Vehicle B is overtaken by your vehicle at a speed
› If the system is still not available, seek the help of a
that is faster by max. 10 km/h. If the speed is higher
specialist garage.
during the overtaking process, no warning will be
provided by the indicator light.
Traffic sign recognition
Indicator light
illuminates - There is another vehicle behind your
Usage
vehicle
The road sign recognition shows road signs in the
ĔashiÄg - There is another vehicle behind your ve-
display of the instrument cluster. This also indicates
hicle, and the turn signal on the same side is switch-
exceeding the speed limit.
ed on
WARNING
For vehicles with Lane Assist, the indicator light will
Road signs on the road always have priority over the
also Ĕash if your vehicle crosses the lane markings in
road signs shown on the display.
the direction of the approaching vehicle. The system
will trigger a steering wheel vibration in this case.
For this, Lane Assist must be activated and the lane
Functionality
marking between the vehicles must be detected.
Displayed road signs
▶ Speed limits
Operating conditions
▶ Overtaking prohibited
▶ Driving bans - one-way tÙaffi
✓ The driving speed is higher than 15 km/h.
▶ Additional characters, e.g. speed limit in wet condi-
✓ No accessories are connected to the trailer sock-
tions
et.
Towing a trailer
If a trailer or other accessory is connected to the
Function restriction
trailer socket, trailer-relevant road signs are also dis-
played.
The system cannot detect lane width. For this rea-
son, it may, for example, draw attention to a vehicle
Driving on roads without speed limits
in a distant lane in the following cases:
If you are on a road with no speed limits, the road
signs will appear in the display.
▶ The vehicle is driving on a road with narrow lanes
or on the lane edge.
Example of road sign display
▶ The vehicle is taking a turn.
The system can draw attention to objects along the
road, such as high guard rails or noise barriers.
In the following cases, the system does not have to
issue a warning of a vehicle, or the warning may be
Example of additional characters
issued incorrectly:
Example of several simultaneously rec-
▶ If the weather conditions are unfavourable.
ognised road signs.
▶ A very fast approaching vehicle.
▶ The vehicle is driving through a sharp bend or a
roundabout.
At the same time, a red display regarding the
speed limit appears in the speedometer.
Settings
Speed units
The speed indications in the road signs shown refer
In the instrument cluster display
In the menu Assist systems.
to the speed units that are common in the country.
For example, the display may refer to 30 km/h or
In Infotainment
30 mph depending on the country.
In the menu
Driver assist systems › Crew Protect Assist proactive occupant protection 141
Restriction
The system response depends on the selected
driving mode.
The system function may be restricted in the follow-
ing cases:
Risk of frontal impact
Applies to vehicles with the Front Assist system.
▶ The sensor is blinded by the sun or oncoming traf-
fi.
The system triggers safety measures when it de-
tects the impending danger of a frontal impact.
▶ The field of view of the sensor is limited by an ob-
stacle or a preceding vehicle.
▶ If the weather conditions are unfavourable.
Function restriction
▶ The vehicle is moving at high speed.
▶ The road signs are hidden, damaged, or are non-
The function may be restricted or unavailable in the
standard.
following cases:
▶ The road signs are attached to ĔashiÄ£ neon signs.
▶ When deactivated in the infotainment in the menu
▶ The navigation map documents are not up-to-date
or not available.
▶ When deactivating the ASR or activating the ESC
Sport
▶
When reversing
Settings
▶ If there is a malfunction in the ESC, reversible seat
belt or airbag system
Activation / deactivation and setting
In the Infotainment system, in the menu
▶ If there is a malfunction or limitation of the Front
Assist system
◼ Traffic Sign Recognition
▶ Show in instrument cluster - Activation/deactivation of
Settings
the additional road signs in the display of the in-
Automatic activation
strument cluster
The system is automatically activated when the igni-
▶ Speed warning: - oÄfi£uÙes a warning when the
tion is switched on.
speed limit is exceeded
▶Warning at over - Increases the speed limit for the
warning when exceeding the permitted speed
Troubleshooting
◼ Trailer detection
Crew Protect Assist faulty
▶ Show road signs relevant to trailers Activation/deactivation
illuminates together with
of the display of road signs relevant to trailers
Message concerning unavailability or function-
▶ Use for route calculation - Activation/deactivation taking
al restriction
trailers in account for route calculation in naviga-
tion
› Seek the help of a specialist garage.
▶ Tap on maximum speed for trailers - Setting the speed limits
for trailer operation
Driver Alert fatigue detection assistant
Functionality
Crew Protect Assist proactive occupant
protection
Driver Alert evaluates the steering behaviour. If it de-
tects fatigue in the driver, a break is recommended.
Usage
In the display of the instrument cluster, the following
symbol lights up from the isolation box.
The system of proactive occupant protection trig-
gers measures to protect vehicle occupants in dan-
WARNING
gerous situations.
There will be no system warning during the so-called
micro-sleep.
Resetting the break recommendation
Functionality
The break recommendation is reset in the following
If the system evaluates the situation as critical, it
cases:
triggers the following safety measures:
▶ The vehicle stops and the ignition is switched off
▶ Open windows are closed except for a small gap.
▶ The vehicle stops, the seat belt is removed and the
▶ The front seat belts are tightened on the body.
driver's door is opened
142 Park Assist systems › Park Pilot parking aid
▶
The vehicle stops for more than 15 minutes
Park Assist systems
In some situations, the system may erroneously
Park Pilot parking aid
issue a break recommendation.
Functionality
Operating conditions
If an obstacle is detected, the Infotainment will dis-
play a visible message and an audible signal will
✓ Driving speed between 60-200 km/h.
sound.
The interval between the signals becomes shorter as
Settings
the clearance is reduced. At a distance of less than
30 cm from the obstacle, a continuous tone sounds.
Activation/deactivation
In the Infotainment system, in the menu
If the driver does not respond to the warning, the
system triggers automatic emergency braking at
speeds below 8 km/h in order to reduce the impact.
Automatic braking can be activated and deactivated
in the infotainment.
Display
The recorded areas vary according to the equipment.
A
Route controlled at the current steering angle
Acoustic signals oÄ/off
One-time deactivation/activation of automatic
braking
Change to the rear view camera display
System fault
Obstacle at a distance of less than 30 cm
Obstacle at a distance of more than 30 cm
Obstacle outside the route
Operating conditions
✓ The driving speed is lower than 15 km/h.
✓ No accessories are connected to the trailer sock-
et.
Turn on/turn off
Switching on
› Engage reverse gear.
Or:
Park Assist systems › Rear view camera 143
› Press the button.
Rear view camera
Automatic switch-on during forward travel
Functionality
When approaching an obstacle at a speed of less
than 10 km/h.
When reversing, the area behind the vehicle is dis-
played in the Infotainment screen complete with ori-
Automatic switch-on does not activate automatic
entation lines.
braking.
The camera is equipped with a cleaning system.
Switching off
Cleaning takes place automatically when the rear
› Disengage reverse gear.
window is washed.
Or:
› Press the button.
Orientation lines and functional surfaces
Automatic switch off
The driving speed is higher than 15 km/h.
Orientation lines
Function restriction
In the following cases, the system does not have to
issue a warning of an obstacle, or the warning may
be issued incorrectly:
▶ If the weather conditions are unfavourable.
▶ The detected obstacles are moving.
▶ Sensor signals are not ÙeĔeted by the surface of
the obstacles.
A
Distance about 40 cm
▶ It is a small obstacle, e.g. a stone or a pillar.
B
Distance about 100 cm
C
Distance about 200 cm
Settings
The distance between the side lines corresponds ap-
The system settings are made in the infotainment
proximately to the vehicle width including mirrors.
system in the following menu:
Function surfaces
Or:
Troubleshooting
After switching on, an audible signal sounds for 3
seconds and there is no obstacle near the vehicle
› Seek the help of a specialist garage.
After switching on, the symbol Ĕashes in the
Brightness, contrast and colour settings of the
button
screen
› Seek the help of a specialist garage.
Turns off the display of the area behind the vehi-
After switching on, not all scanned areas are dis-
cle
played on the Infotainment screen
Switching audible parking signals oÄ/off
› Move the vehicle a few meters forwards or back-
One-time deactivation/activation of automatic
wards.
braking
› If the scanned areas are still not displayed, seek the
help of a specialist garage.
Parking aid full screen view.
Operating conditions
✓ Boot lid closed
144 Park Assist systems › Rear TÙaffi Alert
✓ Ignition on
monitor the tÙaffi behind. At the same time, an
✓ Driving speed less than 15 km/h
acoustic signal sounds.
Operation
Operating conditions
Switching on
✓ No accessories are connected to the trailer sock-
et.
› Engage reverse gear.
Switching off
› Disengage reverse gear.
Function restriction
Manoeuvre Assist’s functionality may be limited in
Restriction
unfavourable weather conditions.
The camera image is distorted in contrast to the nak-
ed eye. The display may only be used to estimate the
Settings
distance.
Activation/deactivation in the instrument cluster
Some items may not be displayed properly on the
display
screen. These include narrow columns, wire mesh
In the menu Assist systems.
fences, grids or road bumps.
Activation/deactivation in Infotainment
In the following menu:
Rear Traffic Alert
Functionality
Or:
When reversing, the
Rear TÙaffi Alert warns
of approaching vehicles.
Troubleshooting
If the driver does not re-
spond to the warning,
Message regarding system unavailability
the vehicle is braked au-
› Stop the engine and start again.
tomatically at a speed
› If the system is still not available, seek the help of a
below 10 km/h.
specialist garage.
Vehicle with Parking Aid
Park steering assistant
If an approaching vehicle is detected in the area be-
hind your vehicle, a graphical warning is displayed in
Usage
the Infotainment. At the same time, a continuous
Park Assist helps drivers park in parallel and perpen-
tone sounds.
dicular parking places and to manoeuvre out of par-
allel parking spaces.
Functionality
The system looks for a parking space and only takes
over the steering during the parking procedure or
when leaving a parking place. The driver operates the
pedals and the shift lever/gear selector.
The system displays information and notes on the in-
Vehicle in collision area - danger of collision!
strument cluster display.
Approaching vehicle
If the system detects a risk of collision, automatic
emergency braking takes place to prevent a collision.
Vehicle without Parking Aid
If an approaching vehicle is detected in the area be-
hind your vehicle, the a warning is displayed in the in-
strument cluster display, indicating to the driver to
Park Assist systems › Park steering assistant 145
Operating conditions
› To return to the original recommended parking
mode, press the button again.
✓ The driving speed is lower than 7 km/h.
Before the parking process
✓ The ASR is activated and there is no intervention.
› If a suitable parking space is found, stop and drive
✓ There is no driver intervention in the automatic
backwards or forwards as indicated by the arrow in
steering operation.
the display.
✓ No accessories are connected to the trailer sock-
› When a steering intervention message is displayed,
et.
release the steering wheel. The steering operation
is taken over by the system.
Operation
Parking operation
Turn on/turn off
CAUTION
› Press the
button.
Risk of injury!
▶ Do not reach between the steering wheel spokes
When the system is switched on, the symbol lights
during the parking manoeuvre.
up in the button
▶ Only operate the pedals and the shift / selector
Select the lane side for the parking procedure
lever.
The system automatically searches for a suitable
› Observe the area around the vehicle and drive
parking space on the passenger side.
backwards or forwards in accordance with the ar-
› Press the driver's side indicator to fiÄd a parking
row in the display.
space on this side of the road.
› As soon as the symbol appears in the display
and an audible signal sounds, stop the vehicle. The
Operation while searching for a parking space
steering wheel is taken over accordingly. The sym-
› Drive past a number of parked vehicles at a dis-
bol
goes out.
tance of 0.5-1.5 m.
› Travel backwards or forwards in accordance with
› To search for a parking space across the road, drive
the arrow in the display.
slower than 20 km/h.
› To search for a parking space along the road, drive
As soon as the parking process is completed, the
slower than 40 km/h.
corresponding message is displayed and an audible
signal sounds.
If the symbol
(km/h) appears in the display, reduce
the driving speed. If the system fiÄds a parking
The parking procedure can be ended at any time by
space, the display will show the recommended park-
pressing the button
ing mode.
When partially parked in a suitable transverse
Changing the parking mode
parking space forward, press button . The parking
If a suitable parking space is found, the following
process is completed by the system.
Park modes can be shown in the display.
Exiting a parking space
› Press the
button.
When the system is switched on, the symbol lights
up in the button
› Follow the instructions on the screen.
Automatic speed reduction
If a speed of 7 km/h is exceeded during the parking
process, the system will reduce the speed.
Upon the speed being exceeded by 7 km/h a second
time, the parking process is terminated.
Park backwards longitudinally
Park backwards crosswise
Function restriction
Park forwards across
If the parking space is too small, it is not possible to
The parking mode can be changed by pressing the
use the Park Assist to initiate a parking manoeuvre.
button
A message is shown on the instrument cluster dis-
play.
Press the button again
and the system is switch-
ed off.
Do not use the Park Assist in the following cases:
146 Engine, exhaust system and fuel › Bonnet
▶
The vehicle is moving on unpaved or slippery surfa-
Engine, exhaust system and fuel
ces.
▶ If snow chains or a spare wheel are mounted on
Bonnet
the vehicle.
Opening the bonnet
▶ If the system chooses an inappropriate parking
space for parking.
Before opening
› Make sure the windscreen wiper arms are folded
down onto the windscreen.
Troubleshooting
› Keep everyone away from the engine compart-
Message regarding system unavailability
ment.
› Stop the engine and start again.
Opening
› If the system is still not available, seek the help of a
specialist garage.
› Pull the release lever
underneath the dash
Incorrect resulting position of the vehicle in the
panel.
parking space
The correct parking procedure depends on the size
of the wheels. If other wheels approved by ŠKODA
AUTO are fitted, have the system readjusted by a
specialist garage.
› Release the lock.
› Open the bonnet.
› Remove the bonnet
stay from the holder
and insert the end of
the stay into the open-
ing in the bonnet.
Closing
› Lift the bonnet.
› Unhook the bonnet stay and insert it into the hold-
er.
› Fold the bonnet down and release it with a dis-
tance of 30 cm remaining.
› Check that the bonnet is closed.
NOTICE
▶ Do not press down on an unclosed bonnet.
▶ Open and close the Ĕap again.
Engine, exhaust system and fuel › Engine oil 147
Engine oil
▶ Diesel engines: VW 507 00, VW 509 00,
ACEA C3, API CJ-4
Checking the fill level and topping up
For vehicles without a particulate filteÙ, VW 505 01
can be optionally used.
Test conditions
✓ The vehicle is on a horizontal surface
Changing
✓ The parked engine is warm
Have the oil changed by a specialist garage.
Checking the level
› Wait a few minutes for the engine oil to Ĕoõ back
Troubleshooting
into the oil sump.
› Remove the dipstick and wipe with a clean cloth.
Engine oil pressure too low
› Insert the dipstick as far as it will go and pull it out
Ĕashes, lights up at the same time
again.
› Read the oil level and push the dipstick back in
or
again.
Ĕashes, lights up at the same time
› Check the engine oil level.
The oil level is OK, the warning light continues to
Ĕash:
› Stop the engine and seek the help of a specialist
garage.
Engine oil level too low
illuminates together with
The oil level must be within the marked range.
or
NOTICE
illuminates together with
Risk of damage to the engine and the exhaust sys-
Message regarding required engine oil top up
tem!
› Check the engine oil level, top up with oil if re-
▶ The oil level must not be outside the marked range.
quired.
If it is not possible to top up the engine oil or if the
oil level is above the marked range, do not continue
Engine oil level too high
driving. Stop the engine and seek the help of a spe-
illuminates together with
cialist garage.
▶ Do not use any oil additives.
or
Consumption
illuminates together with
Depending on driving style and operating conditions,
Message regarding the need to reduce the
the engine consumes some oil, up to 0.5 l/1000 km.
engine oil level
Consumption may be higher over the next 5000 km.
› Check the engine oil level.
RefilliÄg
› Unscrew the cover of the engine oil filleÙ opening.
The oil level is too high:
› Top up the oil to the correct speifiatioÄ in 0.5 li-
› Drive on, exercising appropriate caution.
tre portions.
› Seek the help of a specialist garage.
› Check the oil level.
Engine oil level sensor impaired
› Screw on the cover of the engine oil filleÙ opening.
illuminates together with
SpecificatioÄ
Ask a specialist garage for the correct engine oil
or
speifiatioÄ for your vehicle.
illuminates together with
If no oil of the correct speifiatioÄ is available, max.
Message regarding the engine oil sensor
0.5 l of oil with the following speifiatioÄs may be
› Drive on, exercising appropriate caution.
used until the next oil change:
›
Seek the help of a specialist garage.
▶ Petrol engines: VW 504 00, VW 508 00,
ACEA C3, ACEA C5
148 Engine, exhaust system and fuel › Coolant
Coolant
› Refill with coolant of the correct speifiatioÄ.
› Screw on the cap until it clicks into place.
Coolant temperature gauge
SpecificatioÄ
To Ùefill the coolant additive use G12evo (TL 774 L).
NOTICE
Risk of damage to the cooling system and the en-
gine!
Adding coolant that does not conform to the correct
speifiatioÄ can reduce the corrosion protection of
the cooling system.
Troubleshooting
A
Cold area
Coolant level is too low
› Avoid high engine speed.
illuminates together with
B
Operating range
C
High temperature range
or
illuminates together with
Message concerning the required coolant
Checking the fill level and topping up
check
Test conditions
› Check the coolant level.
✓ The vehicle is on a horizontal surface
If the coolant level is OK:
✓ The engine is turned off and cooled
›
Check the fuse for radiator fan, replace if re-
Checking the level
quired » page 158, Replacing a fuse.
The fill level must be
If the fuse is OK but the indicator light lights up
within the marked range.
again:
› If the fill level is below
› Stop driving! Seek the help of a specialist garage.
the mark
, top up
Coolant temperature too high
the coolant.
illuminates together with
or
illuminates together with
Report regarding the engine overheating
NOTICE
› Stop driving.
Danger of damage to the engine compartment!
› Stop the engine and allow it to cool.
▶ Do not top up the coolant above the marked area.
The coolant could be forced out of the cooling sys-
› Drive on after the indicator light goes out.
tem when heated.
Engine fault
NOTICE
illuminates together with
There must be a small quantity of coolant in the tank.
▶ Do not add coolant when the tank is empty.
or
▶ Stop driving! Seek the help of a specialist garage.
illuminates together with
RefilliÄg
›
Stop driving!
CAUTION
› Stop the engine and seek the help of a specialist
Risk of scalding!
garage.
The cooling system is pressurised.
▶ Do not open the cap of the coolant expansion tank
There is no coolant of the correct specificatioÄ
while the engine is warm. Let the engine cool
available
down.
› Top up with distilled or demineralised water.
› Place a wipe on the lid of the tank and carefully un-
› Have the correct coolant mixing ratio corrected by
screw the lid.
a specialist garage as soon as possible.
Engine, exhaust system and fuel › Engine electronics 149
Another substance was used for topping up, other
power will be reduced, and the START-STOPP func-
than distilled or demineralised water:
tion will not be available.
› Have the coolant changed by a specialist garage.
It is not possible to top up with a sufficieÄt amount
Filter cleaning
of coolant
Conditions for cleaning
› Stop driving.
✓ The engine is warm.
› Stop the engine and seek the help of a specialist
✓ For vehicles with manual transmission, observe
garage.
the gear recommendation shown in the display of
There is a loss of coolant
the instrument cluster.
› Top up the coolant and seek the help of a specialist
Procedure for vehicles with diesel engines
garage.
›
Drive at a speed of at least 60 km/h at engine
speeds of at least 2000 rpm.
Engine electronics
If the filteÙ is successfully cleaned, the indicator light
goes off.
or
Troubleshooting
If the indicator light
or
does not go off with-
Petrol engine control faulty
in 40 minutes, no filteÙ cleaning was performed.
illuminates
› Continue driving, exercising appropriate caution,
Driving in emergency mode is possible - a
and seek the help of a specialist garage.
noticeable reduction in engine performance may oc-
cur.
Procedure for vehicles with petrol engines
› Drive at a speed of at least 80 km/h at engine
› Continue driving, exercising appropriate caution,
speeds between 3000-5000 rpm.
and seek the help of a specialist garage.
›
Release the accelerator pedal and let the vehicle
Diesel engine control faulty
roll with the gear engaged for a few seconds.
Ĕashes
› Repeat this procedure several times.
If the filteÙ is successfully cleaned, the indicator light
Driving in emergency mode is possible - a noticeable
goes off.
or
reduction in engine performance may occur.
If the indicator light
or
does not go off with-
› Continue driving, exercising appropriate caution,
in 30 minutes, no filteÙ cleaning was performed.
and seek the help of a specialist garage.
› Continue driving, exercising appropriate caution,
Diesel preheating system faulty
and seek the help of a specialist garage.
illuminates, or does not illuminate after the
ignition is switched on
Exhaust control system
Driving in emergency mode is possible - a noticeable
reduction in engine performance may occur.
Troubleshooting
› Continue driving, exercising appropriate caution,
Emission control system faulty
and seek the help of a specialist garage.
illuminates
Driving in emergency mode is possible - a no-
ticeable reduction in engine performance may occur.
Particle filter
›
Continue driving, exercising appropriate caution,
Troubleshooting
and seek the help of a specialist garage.
Clogged particle filter
illuminates together with
Fuel filter
or
Troubleshooting
illuminates together with
Water in the diesel fuel filter
illuminates together with
› Clean the filteÙ.
When the indicator light is on, it must be as-
or
sumed that fuel consumption will be higher, engine
illuminates together with
150 Engine, exhaust system and fuel › Radiator blinds
› Continue driving, exercising appropriate caution,
Checking the fill level and topping up
and seek the help of a specialist garage.
Checking the level
The AdBlue® level is monitored automatically.
Radiator blinds
The range with the existing AdBlue® tank fill level as
well as the indication of the minimum and maximum
Usage
AdBlue® top up quantity can be viewed in the driving
The radiator blinds reduce emissions harmful to the
data in the instrument cluster display under the
environment and CO2-Emissions and saving fuel.
menu item
If the range with the existing AdBlue® tank fill level
drops to 0 km, it is not possible to start the engine.
Troubleshooting
› If possible, top up AdBlue® to the maximum level.
If the display of the instrument cluster shows a mes-
sage relating to the function restriction of the blinds,
Requirements for refilliÄg
✓ Vehicle unlocked
the maximum speed of the vehicle is limited to 160
km/h.
✓ Stationary heating switched off
✓ Ignition off
The cause may be ice or snow in the area around the
blinds. After the ice or snow has thawed, the blinds
✓ The vehicle is on a horizontal surface
are functional again.
Methods of refilliÄg
› Should the impairment not be due to ice or snow,
▶ With the fuel nozzle at the petrol station
assistance from a specialist should be sought.
▶ With the Ùefill bottle or from the canister
▶ At a specialist garage
For ÙefilliÄ£ using Ùefill bottles or canisters, we rec-
Fuel filler Ĕap
ommend using Ùefill bottles and canisters from ŠKO-
Opening the fuel filler Ĕap
DA original parts. The Ùefill bottles are equipped with
oveÙfill protective function.
› Press the Ĕap and open
it.
RefilliÄg
› Open the tank Ĕap.
› Turn the tank cap in
the direction of the ar-
row and remove it.
› Place the tank cap on
the tank Ĕap.
› Refill AdBlue®.
The AdBlue® tank is full
when the fuel nozzle
AdBlue
switches off or as soon
as no more AdBlue
®
Regulations
Ĕoõs out of the Ùefill bottle. Do not continue ÙefilliÄ£.
Only use AdBlue® that corresponds with the ISO
› Place the tank cap on the filleÙ neck and turn it in
22241-1 standard. Do not add additives to AdBlue®.
the opposite direction to the arrow until it clicks
into place.
AdBlue® is a registered trademark of VDA and is also
› Close the tank Ĕap and click into place.
popular as AUS 32 (Aqueous Urea Solution) or DEF
(Diesel Exhaust Fluid).
› Before starting the engine, leave the ignition on for
30 seconds to allow the system to detect the Ùefill-
iģ.
Functionality
To reduce pollutant emissions, a urea solution is au-
tomatically injected into the exhaust system - AdBl-
ue®.
AdBlue® freezes at temperatures below -11 C. The
system function is ensured by automatic heating.
Engine, exhaust system and fuel › Petrol 151
NOTICE
Octane number
Risk of damage to the system for injecting AdBlue®
Use the petrol with the octane number prescribed
in to the exhaust system!
for your vehicle.
▶ Do not exceed the maximum Ùefill quantity speci-
Petrol with an octane number that is one higher than
fied in the instrument cluster.
the one prescribed for your vehicle can be used
▶ The service life of AdBlue® is 4 years. If the tank
without restriction.
contents are not consumed within this period, have
NOTICE
them replaced by a specialist garage. When top-
Risk of damage to the engine and the exhaust sys-
ping up, do not use AdBlue® that is past its expiry
tem!
date.
▶ When petrol with a lower than the prescribed oc-
tane is used, only continue driving at mid-range en-
gine speeds and with minimal strain on the engine.
Troubleshooting
▶ Refuel using petrol of the prescribed octane num-
AdBlue®-Level too low
ber as soon as possible.
or or illuminates
▶ Do not use petrol with an octane number that low-
er than 91!
› Refill AdBlue®.
Prescribed petrol 95 / min. 92 or 93 RON / ROZ
AdBlue®-system malfunction.
We recommend using petrol 95 ROZ.
or or illuminates
Optionally, the petrol 92 or. 93 ROZ can be used
› Seek the help of a specialist garage.
(slight power loss, a slightly increased fuel consump-
tion).
In an emergency, 91 RON petrol may be used (low
Technical data
power loss, slightly increased fuel consumption).
AdBlue®-tank filliÄ£ level is about 12 litres.
Specified petrol is unleaded, min. 95 RON / ROZ
Use min. 95 ROZ petrol.
Using higher octane petrol than 95 RON may result
Petrol
in improved performance and lower fuel consump-
tion.
What you should be mindful of
In an emergency 91. 92 or. 93 RON may be used
DANGER
(low power loss, slightly increased fuel consump-
Risk of death!
tion).
Fuel and fuel vapours are explosive.
Prescribed petrol 98 / (95) RON / ROZ
NOTICE
We recommend using petrol 98 ROZ.
Risk of serious damage to the engine and the ex-
95 RON petrol may be used as an option (low power
haust system!
loss, slightly increased fuel consumption).
▶ Never run the fuel tank completely empty!
In an emergency 91. 92 or. 93 RON may be used
If you would like to operate your vehicle in a country
(low power loss, slightly increased fuel consump-
other than that intended for vehicle operation,
tion).
please contact a ŠKODA Partner. They will let you
know whether a suitable fuel is offeÙed in the associ-
Additive
ated country.
NOTICE
Risk of damage to the engine and the exhaust sys-
tem!
Regulations
▶ Do not use petrol containing metal-based addi-
Standards
tives, e.g. manganese, iron, lead, and do not use, for
Petrol must comply with European standard EN 228
example, any LRP-petrol - lead replacement petrol.
(in Russia, GOST 32513-2013).
▶ Do not add any additional additives to the petrol in
accordance with EN 228.
Only use unleaded petrol that contains max 10% bi-
oethanol (E10).
▶ If petrol is not used in accordance with EN 228, we
recommend obtaining information from a specialist
We recommend using petrol with additives,
company regarding the possible use of petrol addi-
which is available at petrol stations at the petrol
tives approved by ŠKODA AUTO.
pumps.
152 Engine, exhaust system and fuel › Diesel
Requirements for refuelling
Diesel
✓ Vehicle unlocked
What you should be mindful of
✓ Ignition off
DANGER
Risk of death!
RefilliÄg
Fuel and fuel vapours are explosive.
NOTICE
› Open the tank Ĕap.
Risk of serious damage to the engine and the ex-
› Turn the tank cap in
haust system!
the direction of the ar-
▶ Never run the fuel tank completely empty!
row and remove it.
If you would like to operate your vehicle in a country
› Place the tank cap on
other than that intended for vehicle operation,
the tank Ĕap.
please contact a ŠKODA Partner. They will let you
› Insert the fuel nozzle
know whether a suitable fuel is offeÙed in the associ-
into the fuel filleÙ neck
ated country.
up to the stop and re-
fuel.
› Do not continue refuel-
Regulations
ling after the fuel noz-
zle switches off.
Standards
The diesel fuel must comply with European standard
› Remove the fuel nozzle and put it back on the pet-
EN 590 (in Russia, GOST 32511-2013 or GOST R
rol pump.
55475-2013).
› Place the fuel cap on the fuel filleÙ neck and turn it
in the opposite direction to the arrow until it clicks
Only use a diesel fuel that contains a maximum of 7
into place.
% biodiesel (B7).
› Close the tank Ĕap and click into place.
We recommend using diesel with additives,
which is available at petrol stations at the petrol
pumps.
Troubleshooting
Operation in differeÄt weather conditions
If fuel other than unleaded petrol has been used as
Only use a diesel fuel according to the current or the
per standards applicable to your vehicle
expected weather conditions.
› Neither start the engine nor switch on the ignition.
Additive
› Seek the help of a specialist garage.
NOTICE
Risk of damage to the engine and the exhaust sys-
Technical data
tem!
▶ Do not use RME biofuel, even as a diesel fuel addi-
The fuel prescribed for your vehicle is indicated on a
tive.
sticker on the inside of the fuel filleÙ Ĕap.
▶ Do not add any additional additives to the diesel in
A
Unleaded petrol
accordance with EN 590.
▶ If diesel is not used in accordance with EN 590, we
B
Organic share as a
recommend obtaining information from a specialist
percentage
company regarding the possible use of diesel addi-
tives approved by ŠKODA AUTO.
Requirements for refuelling
✓ Vehicle unlocked
✓ Ignition off
The fuel tank has a capacity of about 50 litres, in-
cluding a reserve of approx. 7 litres.
For natural gas vehicles, the content of the petrol
RefilliÄg
tank is approximately 9 litres.
Misfuelling protection
illuminates - the fuel level has reached the re-
The fuel filleÙ neck on diesel vehicles may be equip-
serve area.
ped with a misfuelling protection device.
Engine, exhaust system and fuel › CNG (compressed natural gas) 153
In some countries, the diameter of the diesel fuel
illuminates - the fuel level has reached the re-
nozzle may be identical to that of the petrol nozzle.
serve area.
Before driving in these countries, have the protec-
tion device removed by a specialist garage.
CNG (compressed natural gas)
RefilliÄg
› Open the tank Ĕap.
What you should be mindful of
› Turn the tank cap in
WARNING
the direction of the ar-
Natural gas is highly explosive and highly Ĕammable.
row and remove it.
› Place the tank cap on
WARNING
the tank Ĕap.
Risk of death, explosion or fiÙe!
▶ Do not ignore the smell of gas in the vehicle or
› Insert the fuel nozzle
when refuelling.
into the fuel filleÙ neck
up to the stop and re-
▶ The natural gas tanks in the vehicle must not be ex-
fuel.
posed to undesirable heat sources.
› Do not continue refuel-
▶ Do not enter the vehicle when refuelling with natu-
ling after the fuel noz-
ral gas. Electrostatic discharges may occur when
zle switches off.
entering the vehicle. If the fuelling nozzle of the re-
fuelling system is subsequently touched, sparks
› Remove the fuel nozzle and put it back on the pet-
may form and a fiÙe may break out.
rol pump.
› Place the fuel cap on the fuel filleÙ neck and turn it
WARNING
in the opposite direction to the arrow until it clicks
Touching the ĔooÙ of the vehicle or an accident may
into place.
damage the natural gas containers. If damaged natu-
ral gas tanks are refuelled, they can burst and cause
› Close the tank Ĕap and click into place.
serious or fatal injuries!
▶ Ensure a gas system test is carried out immediately
Troubleshooting
by a specialist company.
▶ Do not refuel using natural gas until a gas system
If fuel other than diesel has been used as per appli-
test has been carried out.
cable standards
NOTICE
› Neither start the engine nor switch on the ignition.
Risk of damage to the engine and the exhaust sys-
› Seek the help of a specialist garage.
tem.
The diesel nozzle cannot be inserted correctly into
▶ Do not use Liquefied Natural Gas (LPG), Liquefied
the tank filler neck
Petroleum Gas (LPG) or Hythane (hydrogen/meth-
› If the nozzle cannot be inserted correctly into the
ane mixture).
tank filleÙ neck, move it slightly back and forth
when plugging it in.
Regulations
Technical data
The fuel prescribed for your vehicle is indicated on a
sticker on the inside of the fuel filleÙ Ĕap.
A
Diesel
Variants of the CNG sticker
B
Organic share as a
in natural gas vehicles .
percentage
The fuel tank has a capacity of about 50 litres, in-
cluding a reserve of approx. 7 litres.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст