Skoda Superb iV (2021 year). Manual in english — page 3
Lighting, windscreen wipers and washers › COMING HOME, LEAVING HOME exterior lighting
49
WARNING
The headlights are misted up on the inside
Risk of an accident!
Inside the headlights, moisture may occur. This is not
An incorrectly adjusted headlight range can cause in-
a defect.
suffiieÄt vehicle lighting or can dazzle other road
Malfunction of the automatic headlight circuit
users.
› Clean the windscreen in the area of the rain/light
▶ Adjust the headlight range correctly.
sensor.
Adjust headlights for driving in right / left-hand
Beam of light in front of the vehicle has shortened
traffic
Headlight defective.
Applies to full LED headlights.
› Seek the help of a specialist garage.
› In Infotainment, select the following menu:
Driving lights defective
If a message regarding the failed driving lights is dis-
Or:
played, the light will work in emergency mode.
› Drive on, exercising appropriate caution.
› Activate the travel mode function.
› Seek the help of a specialist garage.
Adapt headlights for the opposite direction of traf-
fic - driving abroad
COMING HOME, LEAVING HOME
Applies to LED headlights.
exterior lighting
› Seek the help of a specialist garage.
Activate / deactivate the dynamic cornering lights
Functionality
function
The COMING HOME function turns on the light after
Applies to full LED headlights.
turning off the ignition and opening the driver's door.
› In Infotainment, select the following menu:
The light switches off automatically after the set
lighting time has elapsed.
The LEAVING HOME function switches on the light
Or:
when unlocking the vehicle with the wireless remote
control.
› Activate or deactivate the function Dynamic cornering
light .
Operating conditions
Troubleshooting
✓ Visibility has worsened.
✓ The light switch is in the
position.
Turn signal light defective
Ĕashes faster - turn signal light on the right de-
fective
Settings
› Check the turn signal light on the right.
This function is set in the following menu in the Info-
Ĕashes faster - turn signal light on the left de-
tainment system:
fective
› Check the turn signal light on the left.
Or:
does not Ĕash when the trailer is hitched -
trailer turn signal light defective
› Check the trailer lighting.
Light Assist high-beam assist system
Light bulb or LED bulb is defective
Functionality
illuminates together with
Information appears in the display regarding
The high beam assist system automatically switches
the defective lights.
the high beam on and off.
› Replace the defective bulb.
WARNING
› In case of a defective LED bulb, contact a specialist
Risk of accident!
garage for help.
▶ If necessary, manually switch the high beam on or
off.
50
Lighting, windscreen wipers and washers › Dynamic Light Assist headlight assist system
Operating conditions
Operating conditions
✓ The system is activated.
✓ The system is activated.
✓ The light switch is in the
position.
✓ The light switch is in the
position.
✓ The driving speed is higher than 30 km/h.
✓ The driving speed is higher than 30 km/h (for
✓ The low beam is switched on.
some countries, higher than 60 km/h).
✓ The low beam is switched on.
Operation
Operation
Switching on
Switching on
› Push the lever in the
direction of the arrow.
› Push the lever in the
direction of the arrow.
It lights up in the instru-
ment cluster
from
It lights up in the instru-
the isolation box.
ment cluster
from
the isolation box.
Switching off
› Manually switch the high beam on or off.
Switching off
› Manually switch the high beam on or off.
Function restriction
Function restriction
The system may dazzle other road users if their
headlights/lights are not detected for the following
The system may dazzle other road users if their
reasons, for example:
headlights/lights are not detected for the following
reasons, for example:
▶ The headlights/lights of oncoming vehicles are
covered by crash barriers, for example.
▶ The headlights/lights of oncoming vehicles are
▶ The headlamps/lights of the oncoming or preced-
covered by crash barriers, for example.
ing vehicle are dirty or not functioning.
▶ The headlamps/lights of the oncoming or preced-
ing vehicle are dirty or not functioning. The system
can also recognize a vehicle as a single-lane means
Settings
of transport.
Activation/deactivation
The function is activated or deactivated in the fol-
Settings
lowing menu in the Infotainment system:
Activation/deactivation
The Dynamic Light Assist is activated or deactivated
Or:
in the following menu in the Infotainment system:
Or:
Dynamic Light Assist headlight assist
system
Functionality
Replace light bulbs
The headlight assist system automatically switches
What you should be mindful of
the high beam on and off.
DIY replacement of the following bulbs is possible.
When the high beam is switched on, it adjusts the
Have the remaining light sources replaced by a spe-
light cone so that the drivers of oncoming and pre-
cialist garage.
ceding vehicles are not dazzled.
The new bulb must conform to the speifiatioÄ of
WARNING
the original light bulb. The name of the bulb is
Risk of accident!
marked on the bulb socket.
▶ If necessary, manually switch the high beam on or
off.
Lighting, windscreen wipers and washers › Replace light bulbs
51
NOTICE
› Press the lock mecha-
Danger of headlight damage due to the ingress of
nisms on the connec-
water and dirt!
tor and remove the
▶ Always fit the protective cap on the headlight cor-
connector.
rectly after changing a bulb.
Conditions for changing a bulb
✓ Ignition off
✓ Light switched off
Replacing the light bulb
› Turn the corresponding
Front turn signal
socket with the bulb
and remove it.
› Remove the protective cap from the headlight.
› Remove the base with the bulb.
› Change the bulb in the
socket.
› Insert the socket with
the light bulb into the
light so that the fixiģ
lugs A fit into the re-
› Turn the defective bulb
in the socket and re-
cesses on the head-
move it.
light.
› Insert a new light bulb
› Fit the protective cap
into the socket and se-
on the headlight again.
cure the light bulb by
turning it in the direc-
Rear turn signal and reversing lights
tion of
› Insert the socket with
Loosen and remove the light
the new bulb into the
› Remove the cover with
light so that the guide
the bracket from the
lugs on the socket are aligned with the corre-
tool kit.
sponding openings in the light.
› Turn the socket clockwise to secure.
Insert and fix the light
›
Insert the connector into the light until it clicks into
place.
› Unscrew the screws
A and remove the
light.
› Insert the lamp with the holes A onto the pins B
in the body.
NOTICE
Risk of damage to the electrical system due to water
ingress!
▶ Make sure that the seal is used correctly when in-
stalling the lamp C .
52
Lighting, windscreen wipers and washers › Interior lighting
NOTICE
Risk of damage to the electrical system!
▶ Make sure that the lines between the lamp and the
body are not pinched when the lamp is inserted.
Interior ambient light
› Screw the light into place.
Usage
› Fit the cover of the light, ensuring it clicks into
place.
The ambient lighting ensures a comfortable atmos-
phere in the vehicle interior.
The lighting only works when the dipped or parking
Interior lighting
lights are on.
Operation
The lighting is also switched on automatically after
opening the door.
Operation of the lighting
Lighting in front and rear
Rear lighting
Settings
Reading lamp left
Reading lamp right
The background lighting brightness settings are set
Automatically switch on and switch off
in the Infotainment system, in the following menu:
When the front light is set to
, the rear light
is automatically switched on or off.
Or:
Switching on automatically
The lighting switches on when one of the following
events occurs.
▶ The vehicle is unlocked
Windscreen wipers and washers
▶ One of the doors is opened
Operating conditions
Automatic switch off
The lighting switches off when one of the following
✓ Engine compartment Ĕap closed
events occurs:
✓ Boot lid closed
✓ Ignition on
▶ The vehicle is locked
▶ The ignition is switched on
▶ About 30 seconds after all the doors have been
Operation
closed
WARNING
If a door remains open and the ignition is switch-
Risk of an accident!
ed off, the lights will turn off automatically after 10
At low temperatures, windscreen washer Ĕuid can
minutes.
freeze on the windscreen and restrict visibility.
Automatic switching oÄ/off of the footwell light-
▶ Only use the windscreen washer when the wind-
ing
screen is warm.
The lighting only works when the dipped or parking
Wipe and wash the windscreen
lights are on.
The lighting is also switched on automatically after
opening the door (e.g. when getting in or out).
Turn on the lighting for the make-up mirror in the
sun visors on the windscreen
› Slide off the cover of the make-up mirror.
Settings
The brightness level of the footwell lighting is set in
the Infotainment in the following menu when the
Fast wiping
low beam or parking light is switched on:
Slow wiping
Depending upon vehicle equipment:
Or:
▶ Intermittent wiping
Lighting, windscreen wipers and washers › Windscreen wipers and washers
53
▶
Automatic wiping controlled by the rain sensor
RefilliÄg windscreen washer Ĕuid
Switching off
WARNING
Tip-wiping (spring-loaded position)
Risk of an accident!
A
Setting the wiping speed for the position
▶ Use windscreen washer Ĕuid that is suitable for the
weather conditions.
Washing and wiping (spring-loaded position)
NOTICE
Depending on the vehicle equipment, the wind-
Risk of damage to the windscreen washer system!
screen washer nozzles of the windscreen can be
▶ When ÙefilliÄ£ the washer Ĕuid, do not remove the
heated automatically.
strainer from the neck of the container.
Clean headlights
NOTICE
When the headlights are switched on, they are
Risk of damage to the headlights!
cleaned the fiÙst time and after every tenth wash of
▶ Only use washer Ĕuid that does not attack polycar-
the windscreen. Setting the spray interval can be
bonates.
carried out by a specialist garage.
NOTICE
Wipe and wash the rear window
Risk of damage to engine compartment compo-
nents!
▶ Close the container after ÙefilliÄ£ the windscreen
washer Ĕuid.
The windscreen washer tank is located in the engine
compartment » page 12.
The container can hold a volume of 3 litres and 6 li-
tres for vehicles with a headlight cleaning system.
When the container is in the left-hand area of the
engine compartment, the volume of the container is
3.5 litres.
Spring-loaded position:
› Open the engine compartment lid » page 182.
▶ Washing and wiping the windscreen
› Gently open the top of the sealing cap.
▶ Cleaning the rear view camera
› Top up the windscreen washer Ĕuid.
Wiping
› Close the sealing cap of the tank.
Switching off
Automatic rear window wiping
Troubleshooting
If the windscreen wiping is performed without inter-
Windscreen washer Ĕuid level too low
ruption, then the automatic regular intermittent wip-
illuminates together with
ing of the rear window takes place.
When the windscreen wipers are switched on, the
› Top up the windscreen washer Ĕuid.
rear window is automatically wiped when the re-
verse gear is engaged.
Frozen windscreen wipers
› Carefully remove frozen windscreen wipers from
the windscreen before switching on the ignition
Settings
and free them from snow and ice.
Activating/deactivating automatic wiping
The functions for automatic rear window wiping and
Folding down windscreen wiper arms and
automatic wiping in the rain can be activated and de-
replacing windscreen wiper blades
activated in the following menu in the Infotainment
system:
For folding down the windscreen wiper from the
screen you must fiÙst adjust the wiper arms to the
folded position.
Or:
54
Heating and air conditioning system › Climatronic automatic air conditioning system
NOTICE
Heating and air conditioning
Risk of damage to the windscreen wipers and the
system
engine compartment lid!
▶ Close the bonnet before lowering the wiper arms
Climatronic automatic air conditioning
from the window.
system
▶ Do not turn on the ignition when the windscreen
wiper arms are folded away.
What you should be mindful of
Set the windscreen wiper arms into the folding po-
▶ We recommend keeping the interior temperature
sition
no more than 5 ° C lower than the outdoor tem-
› Switch the ignition on and off again.
perature.
› Within 10 seconds,
▶ We recommend switching the cooling system off
press the control lever
about 10 minutes before the end of the journey to
down and hold for
prevent odour formation.
about 2 seconds.
▶ Annual disinfection of the air conditioning is rec-
ommended.
WARNING
Danger of misting!
▶ Always keep the fan on.
WARNING
Replace the windscreen wiper blade
Risk of accident!
In recirculation mode, there is no fresh air supply
CAUTION
from the outside. This can result in loss of driver at-
Risk of accident!
tention and fogging up of windows.
▶ Change the windscreen wiper blades once or twice
▶ Keep the recirculation mode switched on for a
a year.
short time only.
› Fold the windscreen wiper arm away from the
windscreen.
Operating conditions for the cooling system
› Press the catch and re-
move the wiper blade.
✓ Outside temperature above 2 ° C
› Insert the new wiper
✓ Running engine
blade until it clicks into
✓ Fan switched on
place.
› Fold the windscreen
wiper arm back onto
Operation
the windscreen.
› Turn on the ignition
and push the control
lever down.
A
Set the temperature for the left side
B
Set the temperature for the right side
C
Set the direction of the air outlet
D
Set the blower speed
E
Set the temperature for the left side
F
Set the temperature for the right side
G
Depending on the equipment:
▶ Switch auxiliary heating and ventilation
oÄ/off » page 56, Usage
Heating and air conditioning system › Climatronic automatic air conditioning system
55
▶
Use of residual engine heat for maintain-
Settings
ing heat in the vehicle interior
Display the settings menu
It is possible to switch on within 30 minutes
› Tap the
button on the Climatronic.
of switching off the ignition.
Or:
Switching off the function takes about 30 mi-
nutes.
› Tap on
in the Infotainment screen.
H
Interior temperature sensor
Switch the seat heating or ventilation
oÄ/off » page 58, Operation
Switch recirculated air mode oÄ/off
The recirculation mode prevents contaminated
outside air getting into the interior of the vehi-
cle.
Switch the windscreen ventilation/defrosting
mode oÄ/off
Switch oÄ/off the windscreen heat-
A
Select Climatronic mode
ing » page 57, Operation
B
Set the direction of the air outlet in manual
Switch oÄ/off the windscreen heat-
mode
ing » page 57, Operation
C
Set the temperature for the left side
Operate Climatronic in the Infotainment sys-
D
Set the temperature for the right side
tem
E
Show the front settings menu
Switch maintenance of the interior tempera-
F
Show the back settings menu
ture oÄ/off according to the temperature set-
ting for the driver's side
Switch the cooling system oÄ/off
Press - Switch on automatic mode
When the cooling system is switched on, the
temperature and humidity in the vehicle will
This function keeps the temperature constant
and prevents the windows from misting.
drop.
Switching on the cooling system prevents the
Hold - Maintain the interior temperature in ac-
cordance with the temperature setting for the
windows from misting up.
driver side (SYNC function)
Switching the windscreen heater
Switch the cooling system oÄ/off
oÄ/off » page 57, Operation
When the cooling system is switched on, the
According to the selected Climatronic mode:
temperature and humidity in the vehicle will
▶ Manual mode - Set the blower speed
drop.
▶ Automatic mode - Set the operating power
Switching on the cooling system prevents the
Switch maintenance of the interior temperature
windows from misting up.
oÄ/off according to the temperature setting for
the driver's side
The rear temperature can also be set on the dis-
play in the centre console at the rear.
The Air Care function reduces the penetration
of pollutants into the vehicle interior. At the
With a temperature setting outside of the number
same time, the air is both circulated and
range, one of the following icons will be displayed in
cleaned.
the Climatronic display:
The air puÙifiatioÄ process is displayed in the
LO Maximum cooling power
Infotainment.
HI
Maximum heating power
For proper operation, the doors and windows
Consumption-friendly operation of the Climatronic
must be closed.
If one of the seats is not occupied, the Climatronic
› To switch oÄ/off Active .
adjusts the air temperature accordingly to reduce
Lock increases in heat output for the rear seat
energy consumption.
heater » page 58, Settings
In the Climatronic display, Eco is displayed.
The function is displayed after tapping the func-
tion surface F .
When the air conditioner is operating, the engine
idle speed may increase automatically.
56
Heating and air conditioning system › Auxiliary heating and ventilation
The air conditioning system is also set in the
could come into contact with easily Ĕammable ma-
ŠKODA Connect application » page 140, Functionali-
terials, e.g. dry grass, spilled fuel etc.
ty.
Further Climatronic settings
Functionality
› To make further settings, press the
button on
the Climatronic
, tap on in the Infotainment
The interior is heated or ventilated according to the
screen.
temperature that is set in the e-Manager
menu » page 63, Settings.
▶ Automatic air recirculation - Automatic air circulation mode
oÄ/off
The system uses fuel from the fuel tank and electri-
▶ Automatic supplementary heater - Switch fast interior heating
cal energy from the high-voltage battery for heating.
oÄ/off
▶ Automatic windscreen heating - Switch oÄ/off the automatic
Operating conditions
windscreen heating
✓ The charge state of the 12-volt vehicle battery is
suffiieÄt.
Troubleshooting
✓ The fuel supply is suffiieÄt, the instrument clus-
Water under the vehicle
ter does not light up
When the cooling system is switched on, water can
✓ The function for using the energy from the high-
drip off the air conditioning system. This is not a leak.
voltage battery for cooling / heating the interior
is switched on when the vehicle is not being
Fogging
charged » page 63, Settings.
› Switch on automatic mode.
Or:
Operation
› Increase the blower speed, switch on the cooling
system, and set the air distribution to the wind-
Switch oÄ/off with the radio remote control
screen.
› Hold down the corresponding key.
Automatic sõitch-off of the cooling system
A
Indicator light
If the coolant temperature is too high, the cooling
system may switch off automatically. This ensures
B
Antenna
suffiieÄt engine cooling.
Switching off
Switching on
Auxiliary heating and ventilation
Usage
The auxiliary heater heats the vehicle interior and the
engine.
Hold the radio remote control with the antenna
The auxiliary ventilation makes it possible to supply
facing upwards.
fresh air to the vehicle interior when the engine is
NOTICE
switched off. As a result, the interior temperature is
▶ Protect the remote control from moisture, strong
lowered, e.g. when the vehicle is parked in the sun.
vibrations and direct sunlight.
Display of the radio remote control indicator light
What you should be mindful of
▶ Lit up green for 2 seconds - switch on
▶ Lit up red for 2 seconds - switch off
DANGER
Risk of poisoning!
Range of the radio remote control
▶ The auxiliary heater must not be operated in en-
The range of the wireless remote control is a few
closed spaces.
hundred meters when the battery is full. For exam-
ple, obstacles or weather conditions can reduce the
DANGER
range.
Risk of fiÙe!
▶ Switch off the auxiliary heater before refuelling.
Switching oÄ/off via the control panel of the air
▶ The exhaust pipe for the auxiliary heater is located
conditioning system
on the underside of the vehicle. Therefore, do not
› Press the button.
stop the vehicle in places where the exhaust gases
Heating and air conditioning system › Heated windscreen
57
Set automatic switching on
If the battery is swallowed, serious or even fatal inju-
ries can result from burns in the digestive tract.
› In the Infotainment, tap
▶ Always keep children away from the radio remote
› Set the desired temperature and activate the auxil-
control and batteries.
iary heating.
▶ If the battery is swallowed, seek medical help im-
› Activate the desired preset time for the departure
mediately.
time » page 63, Settings.
› Use a thin screwdriver
If the vehicle is not being charged, the function
to remove the cover in
for using the energy from the high-voltage battery
the marked area.
for interior cooling / heating must be switched on in
› Open the cover and
order to automatically switch on the auxiliary heat-
push it out.
ing » page 63, Settings.
The auxiliary heating is also set in the ŠKODA
Connect application » page 140, Functionality.
Troubleshooting
› Use a screwdriver to
loosen the battery in
Smoke in the engine compartment
the marked area.
In the engine compartment, smoke and odours may
form during the operation of the auxiliary heater.
› Replace the battery.
This is not a defect.
› Insert the cover and
push it until it audibly
Running the auxiliary heater after stopping the en-
locks into place.
gine
After switching off the system, the coolant pump
and the auxiliary heating will continue running a little
while longer in order to burn the remaining fuel in
the heating.
Heated windscreen
Indicator light in the radio remote control
▶ Flashes green in a slow sequence - the switch-on
Usage
signal was not received
Windscreen heating is used for defrosting or venti-
▶ Flashes red in a slow sequence - the sõith-off sig-
lating the windscreen.
nal was not received
▶ Flashes green in an irregular pattern - the parking
heater is locked, e.g. because the fuel tank is al-
Requirements
most empty or there is an error
✓ Running engine
› Check the level of fuel.
✓ Outside temperature approximately below 35 ° C
› If the fuel quantity is OK, seek the help of a spe-
cialist company.
▶ Lights up orange fiÙst, then green/red - the battery
Operation
is weak, the oÄ/off signal has been received
▶ Lights up orange fiÙst, then Ĕashes green/red - the
Heated rear window
battery is weak, the oÄ/off signal has not been re-
› Press the button.
ceived.
Heated windscreen
▶ Flashing orange - the battery is nearly discharged,
› Tap the button on the Climatronic.
the oÄ/off signal has not been received
Or:
▶ Not lit up - the battery is discharged, the oÄ/off
signal has not been received
› Press the key
on the Climatronic
, tap in
the Infotainment screen.
› Replace the battery.
Windscreen heating switches off automatically after
some time.
Change the battery in the remote control
If the engine is switched off when the heating is on
WARNING
and turned back on again within about 10 minutes,
Risk of death!
the heating is continued.
58
Heating and air conditioning system › Seat heating and ventilation
Settings
The heating is switched on with maximum heating
output. By repeatedly pressing the button, the heat-
Automatic heated windscreen
ing output is reduced until it is switched off.
The heated windscreen switches on automatically if
The output level of the heating is indicated by the
the windscreen mists up.
number of illuminated indicator lights in the button
› Press the button
on the Climatronic control
or in the Infotainment screen.
panel
, tap
in the Infotainment screen.
Models with seat ventilation
Or:
› Tap the or function surface to turn on front
› Tap on
in the Infotainment screen.
seat heating.
The Infotainment screen displays a menu for oper-
ating the front seat heater and ventilation.
Troubleshooting
› Adjust the heating output/ventilation level.
The indicator light in the button or below the but-
If the seat heating and ventilation functions are
ton Ĕashes
both switched on at the same time, the heating out-
The heating does not work as the battery charging
put/ventilation level can only be adjusted in the Info-
level of the 12 volt vehicle battery is too low.
tainment screen.
› Press the or button in the rear centre console
Seat heating and ventilation
to switch on the rear seat heating.
The heating is switched on with maximum heating
What you should be mindful of
output. By repeatedly pressing the button, the
WARNING
heating output is reduced until it is switched off.
Risk of burns!
Display heating output/ventilation level in the but-
▶ Do not switch on the seat heater for persons with
ton
limited perception of pain or temperature.
Seat heating switched on
NOTICE
Seat ventilation switched on
Risk of seat damage!
Seat heating and ventilation switched on
▶ Do not kneel on the seats or otherwise apply con-
If the engine is switched off with the heating/ventila-
centrated pressure to them.
tion switched on and then started again within ap-
▶ Do not turn on the heater in the following situa-
proximately 10 minutes, the heating/ventilation will
tions:
continue according to the setting before the engine
▶ The seat is not occupied.
was switched off.
▶ There are objects on the seat, such as a child
seat.
▶ There are additional seat covers or protective
Settings
covers on the seat.
Lock increases in heat output for the rear seat
heater
Requirements
› To turn the function on or off, press the
but-
ton on the Climatronic
/
in the Infotain-
✓ Running engine
ment screen.
Or:
Operation
› Tap on
/
in the Infotainment
screen.
Depending on the equipment, the front seats can be
When the function is switched on, the heating out-
heated or heated and ventilated. The outer rear seats
put can only be turned down.
can only be heated.
The function also blocks the possibility of setting
Models without seat ventilation
the temperature in the display in the rear centre con-
› Press the or button on the Climatronic to
sole.
switch on the front seat heating.
› Press the or button in the rear centre console
to switch on the rear seat heating.
Heating and air conditioning system › Heated steering wheel
59
Heated steering wheel
Driver information system
Requirements
Analogue instrument cluster
✓ Running engine
Overview
Overview of instrument cluster
Operation
› Press the button on the multifunction steering
wheel.
The heating is switched on with maximum heating
output. By repeatedly pressing the button, the heat-
ing output is reduced until it is switched off.
A
Power display
B
Display
C
Speedometer
D
Fuel gauge
E
Multifunction button:
▶ Setting the time
▶ Reset odometer (trip)
▶ Show distance and days until next service ap-
pointment
F
Bar with indicator lights
G
Rev. counter with high-voltage battery charge
indicator
NOTICE
Risk of serious damage to the engine and the ex-
haust system!
▶ Never run the fuel tank completely empty!
In poor visibility and with dipped headlights off,
the brightness of the instrument cluster lighting is
reduced to remind the driver to turn on the light.
Power display
60
Driver information system › Analogue instrument cluster
A
Energy recovery
Operation
The energy generated during braking is stored in
Operation via the multifunction steering wheel
the high-voltage battery during recuperation.
A
Turn - Switch be-
B
Internal combustion engine speed
tween menu
C
Boost
items/set values
Status of full acceleration using the internal
Press - oÄfiÙm the
combustion engine and the electric motor.
menu item
Press - Return to the
Display overview
menu one level high-
Depending on the equipment, the following informa-
er
tion is shown in the display.
Hold - Show main
A
Time
menu
B
Selected gear/gear
Press - Show previous menu (if one has been se-
recommendation
lected) / Show telephone menu
Also included de-
pending on vehicle
Settings
equipment:
▶ Compass direction
Setting the language
display
The language is set in the Infotainment in menu
▶ Automatic gearbox
selector lever posi-
Setting the time
tions
▶ Detected road signs
› Press and hold the button in the instru-
ment cluster until the menu item Time is
C
Menu, indicator lights and information
displayed.
D
Outside temperature
› Release the button, the display shows the hour set-
or
- low outside temperature
ting.
E
Total distance travelled
› Press the button repeatedly to set the hours.
F
Trip - Distance travelled after resetting the
› Wait 4 seconds, the display shows the minute set-
memory
ting.
› Press the key repeatedly to set the minutes.
Overview of the main menu items
› Wait 4 seconds, the display shows the initial set-
▶ Driving data » page 62, Overview
ting.
▶ Assist systems - Activate/deactivate assist sys-
tems
The time is also set in the Infotainment in menu
▶ Navigation - e.g. Display driving recommendations,
compass, list of destination
Resetting the odometer
▶ Audio - Using radio and media
› BÙieĔû press the button in the instrument
▶ Telephone - Call list, accept or reject an incoming
cluster.
call
▶ Vehicle - Vehicle condition » page 65, Display.
Setting the brightness of the instrument cluster
lighting
The brightness of the instrument lighting is adjusted
automatically according to the given lighting condi-
tions.
When low beam is switched on, the brightness of
the instruments lighting can be adjusted in the fol-
lowing menu in the Infotainment system:
Or:
Driver information system › Digital instrument cluster
61
Digital instrument cluster
Settings
Overview
Setting the language
The language is set in the Infotainment in menu
Overview of instrument cluster
Resetting the odometer in the instrument cluster
›
Select Trip in the menu in instrument cluster display.
A
Turn - Select infor-
mation
Press - oÄfiÙm in-
formation
Hold - Reset counter
A
Bar with indicator lights
B
Charge level indicator for high-voltage battery
C
Fuel gauge
Setting the time
The time is set in the Infotainment in menu
D
Display
Setting the brightness of the instrument cluster
E
Additional information
lighting
F
Central display area
The brightness is adjusted automatically according
to the given lighting conditions.
NOTICE
Risk of serious damage to the engine and the ex-
The brightness is adjusted with the dipped beam
haust system!
switched on in the infotainment in the following
▶ Never run the fuel tank completely empty!
menu:
Overview of the main menu items
▶ Driving data » page 62, Overview
Or:
▶ Assist systems - Activate/deactivate assist sys-
tems
▶ Navigation - e.g. Display driving recommendations,
Set the variant of the display
compass, list of destination
› Press the button on the multifunction steering
wheel to change the variant of the display presen-
▶ Audio - Using radio and media
tation.
▶ Telephone - Call list, accept or reject an incoming
call
Select displayed variants
▶ Vehicle - Vehicle condition » page 65, Display.
› Press and hold the button on the multifunction
steering wheel.
› Select and oÄfiÙm the menu item for the display
Operation
variants.
› Select one of the following variants of the display
A
Rotate - Switch be-
and oÄfiÙm.
tween menu
items/Set values/
Manually change
map scale
Press - oÄfiÙm the
menu item
Turn and press - Ac-
tivate automatic
map scale changing
Press - Return to the menu one level higher
Hold - Show main menu
Press - Change the variant of the display
Hold - Display the menu of preset options with
additional information
62
Driver information system › Driving data
A
Classic display
In Infotainment
B
Advanced display
C
Modern display
D
Basic display
E
Sporty display (depending on equipment)
Choose display of additional information
› Press and hold the button on the multifunction
steering wheel.
› Select and oÄfiÙm one of the following pÙefix op-
tions (the scope of the pÙefix options depends on
A
Distance travelled
the type of Infotainment):
B
Driving time
▶ Auto - Information depending on the selected
driving mode
C
Average speed
▶ Classic - Information about the selected gear
D
Average fuel consumption
and the current speed
E
Average power consumption
▶ Adjustable pre-selection options.
F
Fuel range
Setting the pre-selection option for the display of
G
Electric range
additional information
The pre-selection option for displaying additional in-
H
Graphical fuel and power supply gauge - If the
formation is set in the Infotainment system in the
expected range is less than 300 km, the vehicle
following menu:
slowly approaches the symbol
Menu item for the virtual cockpit
I
Total range
Or:
Memory
Menu item for the virtual cockpit
The system saves the driving data in the following
memories:
Since start
▶ Driving data from the time of switching on the ig-
nition until the ignition is switched off again is stor-
ed in the memory. If the journey is interrupted for
more than 2 hours, the memory will be reset.
Long-term
▶ The driving data of all trips up to a total of 99
hours and 59 minutes driving time or 9999 km
driving distance is stored in the memory. If one of
› Select the desired additional information in the A
the listed values is exceeded, the memory is reset.
areas.
Since refuel
› The desired function area for the preselection op-
▶ Driving data from the time the fuel tank was last
tion in the area B hold to save the selection (the
filled is stored in the memory. The memory is reset
scope of the preset options depends on the type
the next time the tank is filled.
of Infotainment).
Operation
Driving data
Display driving data in the display of the instru-
Overview
ment cluster via the multi-functional steering
wheel
The driving data display works with the ignition
› Select the menu item for the driving data in the
switched on.
main menu in the instrument cluster display.
In the instrument cluster display
Depending on the equipment, the display of the in-
strument cluster shows information such as speed,
fuel consumption, range, etc.
Driver information system › e-Manager
63
A
Rotate - Select in-
Setting units
formation/Set values
The units are set in the following infotainment menu:
Press - oÄfiÙm in-
formation
Or:
e-Manager
Settings
Displaying driving data in the infotainment system
The driving data is displayed in the following menu in
Display main menu
the infotainment system:
› Turn on the ignition.
Menu item for driving data
› In infotainment select menu
Or:
The following menu is displayed:
Menu item for the driving data
Select memory for driving data in the display of
the instrument cluster via the multifunction steer-
ing wheel and reset it
› To select the memory
for the displayed driv-
ing data, press control
wheel A repeatedly.
› To resetthe memory,
A
Menu items for setting the departure time with
hold the dial A .
the following functions and information:
▶ Activation/deactivation of the set departure
time
▶ Set the departure time and day of the week-
Selecting the memory in the infotainment system
day(s)
To select the memory, use the functional areas
▶ Activated repetition of the set departure
in the following menu in the infotainment system:
time
Menu item for driving data
▶ Activated charging
Or:
▶ Activated interior cooling/heating
B
Set the departure time and day of the week
Menu item for the driving data
C
Set functions
Resetting the memory in the infotainment system
The memory is reset in the following menu in the in-
D
Activate/deactivate the stand-by heat-
fotainment system:
ing » page 56, Usage.
E
When the heating is running, the windows are
displayed in orange
Or:
When ventilation is running, the windows are
displayed in blue
F
Charging status of the high-voltage battery
Settings
G
Set desired interior temperature
H
Set reduced charging current
Select driving data to be displayed
The driving data to be displayed is selected in the
Setting the departure time
following Infotainment menu:
› In the main menu, select one of the menu items for
setting the departure time.
Or:
In the menu that is displayed, the following menu
items can be set or switched on:
▶ Departure time
64
Driver information system › e-Display
▶
Weekday(s)
Energy Ĕoõ display
▶ Repeat for the selected weekday(s)
▶ Interior cooling / heating
▶ Charging
▶ Low taÙiff
▶ Time lapse for low taÙiff
More settings
› Tap on the main menu function area
In the menu that is displayed, the following menu
items can be set or switched on:
▶ Desired interior temperature
▶ Use of the energy from the high-voltage battery
for interior cooling/heating
If the function is not switched on, the interior cool-
ing/heating is started only when charging.
▶ Value for charging current
▶ Lower battery charging limit
e-Display
Overview
Range monitor
The range monitor displays the electrical range as
well as the effet of switched-on consumers of the
Electric motor active
energy consumption. By tapping on the function sur-
Combustion engine active
face Potential a list of other consumers is displayed.
Energy recovery (recuperation)
Zero Emission
Electric motor and combustion engine active
The Zero Emission view shows the total distance
covered from the start of the journey as well as the
1
The electric motor is active.
proportion of the distance travelled using electric
2
The vehicle is driven by the electric motor, the
drive.
high-voltage battery discharges.
3
High-voltage battery
4
The combustion engine is active.
5
The vehicle is driven by the combustion engine,
and the state of charge of the high-voltage bat-
tery is maintained.
6
The high-voltage battery is charged by energy re-
cuperation.
7
At full acceleration, the electric motor and the
combustion engine are active, and the high-volt-
age battery discharges.
Driver information system › Speed limit warning
65
The energy Ĕoõ is displayed using coloured repre-
Menu item for the vehicle status
sentations.
▶ Green - energy Ĕoõ from the high-voltage battery
(operated by electric motor) or to the high voltage
battery (battery charging).
▶ Orange - energy Ĕoõ from the combustion engine
to the driven axle (operated by combustion en-
gine).
▶ Blue - energy recovery through idling thrust or re-
cuperation.
A
Vehicle areas displayed in colour indicate associ-
Operation
ated warnings
Display in Infotainment
B
No ÄotifiatioÄ
› Turn on the ignition.
Warning messages regarding the vehicle con-
› In the Infotainment, tap
dition and their quantity
› Select the desired e-display by tapping the func-
tional surface or
Functionality
Speed limit warning
In the event of a system fault, messages regarding
the fault in question are displayed on the instrument
Usage
cluster display when the ignition is switched on.
The system offeÙs the possibility to set a speed limit
Messages in relation to faults can also be displayed in
beyond which an acoustic warning signal will sound
the Infotainment.
and the following warning message appears in the
The warning messages will continue to be dis-
display of the instrument cluster.
played until the malfunctions have been remedied.
After the fiÙst display of the message, only the indi-
cator lights
(Hazard) or
(Warning) are dis-
Settings
played.
Setting the speed limit
› Select Warning at or
(depending on the display type)
and oÄfiÙm.
› When the vehicle is stationary, set the desired
speed limit and oÄfiÙm.
› While driving, drive at the desired speed and con-
fiÙm it as the speed limit.
Resetting the speed limit
› Select Warning at or
(depending on the display type)
and oÄfiÙm.
› To reset the speed limit, oÄfiÙm the stored value.
If the journey is interrupted for more than 2 hours,
the set limit is deactivated, but the set value remains
stored.
Vehicle status
Display
The vehicle status is displayed in the following menu
in the infotainment system:
Menu item for the vehicle status
Or:
66
Infotainment Bolero › Infotainment overview
▶ Turn: Set volume
Infotainment Bolero
Control dial right
Infotainment overview
▶ Press: oÄfiÙm menu item
▶ Turn: select menu item/set value
Bolero Infotainment system with navigation func-
tion
Radio menu
Media menu
Phone menu
Voice control
Infotainment settings
SmartLink menu
Information about vehicle settings
Overview of Infotainment menus
System
A
Touchscreen
Limitation
Control dial left
For safety reasons, operation of some Infotainment
▶ Press: Switch Infotainment oÄ/off
functions while driving is not possible or is restricted.
▶ Turn: Set volume
The Infotainment system indicates this by means of
Control dial right
a message in the screen.
▶ Press: oÄfiÙm menu item
▶ Turn: select menu item/set value
Basic settings
Radio menu
Media menu
Setting basic functions
The following Infotainment functions are set in the
Phone menu
menu:
Voice control
▶ Time and date
Navigation menu
▶ Language
SmartLink menu
▶ Units
Information about vehicle settings
▶ Restore factory settings
Overview of Infotainment menus
Sound settings
The Infotainment sound is set in the menu
Bolero Infotainment without the navigation func-
The following menu items can be set:
tion
▶ Setting the equalizer
▶ Adjusting the volume ratio
▶ Volume adjustment of individual Infotainment
functions
The volume can be adjusted on e.g. one of the fol-
lowing menu items:
▶ Volume adjustment of voice commands
▶ Setting the maximum volume when Infotainment
is turned on
▶ Speed-dependent volume setting
▶ Setting the Infotainment to mute with the park-
ing aid switched on
A
Touchscreen
Depending on the equipment, the following ad-
Control dial left
vanced sound settings can be set
▶ Press: Switch Infotainment oÄ/off
▶ Setting space optimisation
Infotainment Bolero › Screen
67
▶
Setting the audio pÙofiles according to genre
The system update ensures optimal function of the
▶ Adjusting the subwoofer volume
Infotainment system, e.g. compatibility with new
phones.
CoÄfiguratioÄ wizard
The oÄfi£uÙatioÄ wizard helps to set certain Info-
Determine system version
tainment functions.
› Tap
System information.
The oÄfi£uÙatioÄ assistant is automatically displayed
Install the navigation function
if the ignition is switched on and if there are at least
In some countries it is possible to use the Infotain-
two menu items that have not been set up after
ment to extend the function of Navigation.
switching on the Infotainment.
The function is available through the online service
› To switch off the automatic display, when the
Shop or from a specialist company.
oÄfi£uÙatioÄ assistant is displayed tap Don't show
again .
› For manual display tap
Configuration wizard .
Screen
Set up menu HOME
Overview
› To display another page of the HOME menu, press
the screen with two fiÄ£eÙs and drag it to the left
or right.
To add the preferred menu, proceed as follows:
› Tap on an empty functional surface.
Or:
› Press and hold an occupied functional surface and
then tap on an empty functional area.
› Select a menu with the desired dimension of the
functional surface.
A
Status bar
› Tap on to exit edit mode.
B
Bar with the functional surfaces of the displayed
To remove the preferred menu, proceed as follows:
menu
› Press an occupied functional surface.
C
Display of the control centre
› Tap on .
D
Other pages of the menu
› Tap on to exit edit mode.
Set up menu MENU
The position of the functional surfaces in the MENU
Operation
menu can be customized as follows:
NOTICE
› Press and hold the desired functional surface until
Danger of screen damage!
it is free.
▶ The Infotainment screen is operated by touching it
› Move the functional surface to a diffeÙeÄt position.
lightly with your fiÄger.
In principle, operation by touch is identical to the op-
Troubleshooting
eration of a mobile phone.
The following operating modes are speifi to the In-
Infotainment not responding
fotainment system.
If the infotainment does not respond, restart it as
follows:
Dragging up or down with two fiÄgers
› Hold for longer than 10 s.
▶ Quickly review the list
› Wait for the restart to complete.
of phone contacts
▶ Switch 2D/3D map dis-
play
System update
We recommend having the system update carried
out by a specialist company.
68
Infotainment Bolero › Infotainment keyboard
Dragging left or right with two fiÄgers
▶ Display the time
▶ oÄfiÙmatioÄ sounds and animations
▶ Display next page of
the HOME menu
Infotainment keyboard
Keypad overview
The arrangement of the keyboard characters de-
Pulling apart with two fiÄgers
pends on the set infotainment language.
Depending on the context, the following types are
▶ Enlarge image
used in infotainment:
▶ Zoom into the map
▶
Alphanumeric
▶ Numeric
▶ Keyboard for input
▶ Keyboard for search
Pulling together with two fiÄgers
▶ Minimize image
▶ Zoom out of the map
Turn two fiÄgers
Keypad example
▶ Rotate image
A
Input line
▶ Rotate the map
▶ Delete characters before the cursor
▶ Tap: delete the last character
▶ Hold: delete all characters one after the oth-
er
▶ Display functional surfaces for moving the
Contactless gesture control
cursor in the input line
The Infotainment menus marked with the symbol
can be controlled by hand gestures.
▶ Move cursor to the left
› Gesture control is ach-
▶ Move cursor to the right
ieved by slowly moving
B
Entries found
the hand back and
▶ Show list
forth approximately 8
cm above the lower
C
Keypad functional surfaces
edge of the screen.
▶ Change to lowercase
Depending on the set-
▶ Switch to fiÙst having an upper-case letter,
ting, a recognized ges-
followed by lower-case letters
ture can be oÄfiÙmed acoustically and animated.
▶ Switch to uppercase
Displaying operation help
▶
/
Switch to the language keypad
› Tap on
▶
Switch to the numeric and character key-
pad
▶
/ Switch to other character variants
Settings
▶ Show additional keyboard languages
The following basic screen functions are set in the
▶ Insert spaces
menu
Screen:
▶ The next line
▶ Brightness level of the screen
▶ Hold: Show more character variants
▶ Switch off the screen
Infotainment Bolero › Voice control
69
▶ Show password
Setting up additional keyboard languages
▶
oÄfiÙm the entered characters
› Tap
Additional keypad languages.
Numeric keypad
Voice control
Functionality
Voice control principle
Voice control works according to the principle of
dialogue between the user and the Infotainment sys-
tem.
The user says a voice command. The Infotainment
system responds or executes the voice command.
Keypad example
Advanced voice control
A
Input line
The vehicle's advanced voice control enables the ve-
hicle functions to be searched and operated online.
▶ Delete characters before the cursor
Advanced voice control understands ĔueÄt whole
▶ Tap: delete the last character
sentences. You do not need to use set commands or
▶ Hold: delete all characters
phrases.
B
Keypad functional surfaces
The advanced voice control can, for example, search
for special destinations or dictate SMS messages if
▶
oÄfiÙm the entered characters
the connected telephone makes this possible.
If it is possible depending on the context, alpha-
This function allows you to combine the search in
numeric characters can be entered by holding a
the online and offliÄe data of the Infotainment. The
function area with the number.
transition between online and offliÄe search is seam-
less and imperceptible to the user.
Operation
The Infotainment keypad is used to enter characters,
Operating conditions
letters and numbers.
✓ Ignition on
The keypad will be automatically displayed when In-
✓ Infotainment switched on
fotainment prompts for characters.
Operating conditions for advanced voice control
Find
To use the advanced voice control, the following
When entering characters, corresponding entries are
conditions must also be met:
searched for.
✓ The vehicle supports the function.
The entry to be searched for can be entered includ-
✓ The vehicle has Infotainment and functions that
ing diacritics.
can be controlled by the advanced voice control.
The keyboard will only provide characters that
✓ The ŠKODA Connect services are active.
match the stored entries.
✓ The vehicle is within range of a contractual mo-
› To display searched entries tap
bile network, through which the connection to
ŠKODA Connect Services is ensured.
Show additional keypad languages
To use the additional keypad languages, the desired
✓ The level of protection of personal data is set to
languages must be set fiÙst.
Share my position .
› Tap or repeatedly tap the Ĕa£ symbol until the
Requirement for recognition of the activation
desired language keypad is displayed.
command
✓ Activated menu item
Voice control Active
Further character variants
› Press and hold the sign with the symbol
› Select the desired symbol.
Operation
Switch on voice control
› Press the
button on the multifunction steering
wheel.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст