Skoda Fabia (2019 year). Manual — part 15
No.
Power consumer
37
Radar
38
Not assigned
39
Not assigned
40
Databus
41
Rear window heating
42
Power windows - front passenger
43
Tow hitch
44
Cigarette lighter, 12-volt power socket
45
Power windows - rear right
46
Front and rear window washer, operating lever under the steering
wheel
47
Tow hitch
48
Tow hitch
49
Fuel pump
50
Infotainment
51
Heating of the external mirror
52
KESSY
53
KESSY steering lock
54
Not assigned
55
Not assigned
56
Not assigned
57
Not assigned
58
Not assigned
59
Not assigned
Fuses in the engine compartment
Fig. 283 Remove the cover
Read and observe and on page 234 first.
Replacing fuses
›
Remove the ignition key, turn off the lights and all electrical consumers.
›
Press together the lock buttons of the cover simultaneously in the direction
of arrow
1
and remove the cover in the direction of arrow
2
.
›
Remove the plastic clip from the holder on the cover of the fuse box in the
dash panel.
›
Use the clip to pull the fuse out, then insert a new fuse.
›
Replace the cover, push the lock buttons of the cover together and lock.
›
Replace the clamp in the original position.
CAUTION
The cover of the fuse box in the engine compartment must always be used
correctly, otherwise water may penetrate into the fuse box – there is a danger
of damage to the vehicle!
236
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fuse assignment in engine compartment
Fig. 284
Fuses
Read and observe and on page 234 first.
No.
Power consumer
1
Radiator fan
2
Not assigned
3
ABS or ESC
4
Not assigned
5
Not assigned
6
Automatic gearbox
7
Engine control system
8
Windscreen wipers
9
Battery data module
10
ABS or ESC
11
Vacuum pump for the brake system
12
Injectors, valve for fuel metering, control valve for oil pressure, valve
for exhaust gas recirculation cooler, negative pressure pump
13
Brake pedal switch
14
Fuel pump, coolant pump
15
Engine control system
16
Starter
17
Engine control system
No.
Power consumer
18
Radiator fan, wastegate, oil temperature sensor, valve for activated
charcoal filter, valve for intake manifold
19
Lambda probe
20 Ignition coils
Bulbs
Introduction
This Owner's Manual only describes the replacement of bulbs where it is possi-
ble to replace the bulbs on your own without any complications arising. Other
bulbs or LED lights must be replaced by a specialist garage.
We recommend having bulbs replaced by a specialist garage or seeking other
expert help in the event of any uncertainties.
▶
Switch off the ignition and all of the lights before replacing a bulb.
▶
Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
We recommend having the headlight settings checked by a specialist garage
after replacing a bulb in the low, high or fog beam.
WARNING
■
Always read and observe the warnings before completing any work in the
engine compartment
■
Accidents can be caused if the road in front of the vehicle is not suffi-
ciently illuminated and the vehicle cannot or can only be seen with difficulty
by other road users.
■
H7 and H8 bulbs are pressurised and may burst when changing the bulb -
risk of injury! We therefore recommended wearing gloves and safety
glasses when changing a bulb.
237
Fuses and light bulbs
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
■
Do not take hold of the glass bulb with naked fingers (even the smallest
amount of dirt reduces the working life of the light bulb). Use a clean cloth,
napkin, or similar.
■
The cap of the filament bulb must always be seated correctly in the head-
light, otherwise this may allow water and debris to enter the headlight - risk of
damage to the headlights.
Note
We recommend that a box of replacement bulbs always be carried in the vehi-
cle.
Bulb arrangement in the front headlights
Fig. 285 Left headlight: Halogen / LED
Read and observe and on page 237 first.
Bulb arrangement
Low beam
High beam and flashing light
Flashing
A
B
C
Cover the front wheel Removing / replacing
Fig. 286
Remove plastic cover
Read and observe and on page 237 first.
The cover in the front wheel well must be removed in order to change certain
light bulbs.
Details about removing the cover if needed, are given in the description of
each lamp change.
Removal
›
Set the front wheels so that the respective cover is accessible.
›
Insert the clamp for removing the full wheel covers
kitinto the recess in the cover.
›
Remove the cover by pulling the hook in the direction of arrow
Inserting
›
Insert and push the cover into the corresponding opening.
The cover must engage securely.
238
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Remove/replace the mounting for the mopping water container
nozzle
Fig. 287 Remove the mounting for the mopping water container nozzle
Read and observe and on page 237 first.
The mounting for the mopping water container nozzle must be removed in or-
der to replace some light bulbs. The holder is located in the engine compart-
ment, front right.
Details about removing the mounting, if needed,are given in each lamp re-
placement description.
Removal
›
Remove the container nozzle
A
from the holder in the direction of arrow
1
›
Insert a finger into the recess
B
in the direction of arrow
2
and lift the
catch
C
in the direction of arrow
3
.
›
Remove the holder of the container nozzle in the direction of arrow
4
.
Inserting
›
Slide the holder of the container nozzle in the opposite direction to the arrow
4
.
The holder must engage firmly.
›
Push the container nozzle into the holder in the opposite direction to the ar-
row
1
.
Changing bulbs for low and main beam (Halogen headlights)
Fig. 288 Removing bulbs for low and main beam
Read and observe and on page 237 first.
›
Before changing the light bulb for dimmed headlights, remove the associ-
ated cover in the front wheel arch
›
Before changing the light bulb for high beam in the right headlight, first re-
move the bracket of the wash water tank support
.
›
Remove the protective caps
A
or
B
›
Disconnect the connector with the light bulb in the direction of arrow
1
.
›
Remove the connector to the bulb in the direction of arrow
2
.
›
Remove the connector.
›
Plug the connector into the new bulb so that the fixing lug
A
on the bulb
points upwards.
›
Insert the connector, with the bulb, into the headlight opposite to the direc-
tion of arrow
2
until you feel it lock into place.
›
Use the protective caps
A
or
B
›
After changing the light bulb for high beam in the right headlight, replace
the bracket of the wash water tank support
239
Fuses and light bulbs
-------------------------------------------------------------------------------------------------------------------------------------------------------------
›
After changing the light bulb for dimmed headlights, replace the cover in the
front wheel arch
Changing the bulb for the front turn signal light
Fig. 289 Changing the bulb for the front turn signal light
Read and observe and on page 237 first.
›
Before changing the lamp in the right headlight, first remove water container
nozzle bracket
›
Remove the protective caps
B
or
C
›
Turn the holder with the bulb in the direction of the arrow
1
›
Remove the holder with the bulb in the direction of arrow
2
.
›
Hold the housing containing the bulb in area
A
.
›
Remove the faulty bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb in the holder until it stops.
›
Insert the holder with the new bulb into the headlight in the opposite direc-
tion to the arrow
2
.
›
Turn the holder with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Use the protective caps
B
or
C
›
After changing the bulb in the right headlamp, reuse the bracket for the
wash water container nozzle
.
Changing light bulbs for fog lights
Fig. 290 Removing the number plate light / replacing the bulb
Read and observe and on page 237 first.
Remove the protective grille and headlight
›
Insert the clamps for removing the full wheel trims into opening
A
.
›
By pulling the hook in direction of arrow
1
, remove the protective grille in
the direction of arrow
2
.
›
Unscrew the screws
B
using the screwdriver from the tool kit.
›
Remove the headlight in the direction of arrow
3
.
Replacing the light bulb
›
Press the latch on the connector in the direction of arrow
4
.
›
Remove the key in the direction of the arrow
5
.
›
Turn the holder with the bulb to the stop in the direction of the arrow
6
.
›
Remove the holder with the bulb in the direction of arrow
7
.
›
Insert a new holder with the bulb in the headlamp and turn it in the direction
of arrow
6
as far as the stop.
›
Attach the connector.
240
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Refit the headlight and grille
›
Replace the fog light by inserting it in the opposite direction of the arrow
3
›
Insert the guard and push it gently until it locks into place.
Removing/installing tail light
Fig. 291 Remove light / pull out connector
Read and observe and on page 237 first.
Removing
›
Open the tailgate.
›
Unscrew the screws
A
with the screwdriver from the tool kit.
›
Into the opening
B
insert the clamps for removing the full wheel trims, di-
rected with the eyelet downward (in the right light with the eyelet upward).
›
Grasp the light with the palm of your hand and remove carefully from pin
D
in the direction of the arrow
1
.
›
Press the latch
C
on the holder in the direction of the arrow
2
.
›
Press the latch in the direction of arrow
3
and pull out the holder in the di-
rection of arrow
4
.
Fitting
›
Insert the bulb holder into the lamp.
›
Tighten the lock in the opposite direction to the arrow
2
» Fig. 291
.
›
Insert the lamp with the holes
D
onto the pins
E
in the body.
›
Carefully press the light into the pins on the bodywork
.
›
Screw the light into place.
›
Shut the boot lid.
CAUTION
■
Ensure that the cable bundle does not become stuck between the body and
the lamp when it is being refitted – or there is a risk of damage to the electrical
installation and risk of water ingress.
■
If you are not sure whether the wiring harness has become pinched, we rec-
ommend that you have the light connection checked by a specialist garage.
■
Ensure that the vehicle paintwork and the tail lamp are not damaged when
removing and installing the tail lamp.
Replacing bulbs in the rear lamp - Option 1 (with LED lamps)
Fig. 292 Outer part of the lamp/holder with bulbs
Read and observe and on page 237 first.
›
Unlock the bulb holder at the areas marked with arrows
and re-
move from the light.
›
Turn the respective light bulb counter-clockwise to the stop and remove it
from the bulb holder.
›
Insert a new bulb into the holder and turn in a clockwise direction to the
stop.
›
Insert the bulb holder into the light
. The holder must engage securely.
CAUTION
■
Before inserting the bulb holder into the light , check that the connector
A
is fitted correctly between the light and the bulb holder.
■
Make sure that when refitting the bulb holder into the light, the wiring har-
ness
B
is not pinched - otherwise there is a risk of damage to the electrical
installation.
241
Fuses and light bulbs
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Replacing the bulbs in the tail lamp assembly - Variant 2
Fig. 293 Outer part of the lamp / removing the bulb / lamp holder
Read and observe and on page 237 first.
Outer part of the lamp
›
Turn the holder with the bulb
A
in the direction of arrow
1
.
›
Remove the socket with the bulb from the lamp housing in the direction of
arrow
2
.
›
Jiggle the bulb to remove.
›
Insert a new bulb into the socket.
›
Reinsert the holder with the bulb into the lamp housing and turn in the oppo-
site direction of the arrow
1
to the stop.
Inner part of the light
›
Unlock the bulb holder at the areas marked with arrows
and re-
move the bulb holder from the light.
›
Turn the respective light bulb counter-clockwise to the stop and remove it
from the bulb holder.
›
Insert a new bulb into the holder and turn in a clockwise direction to the
stop.
›
Insert the bulb holder in the light. The holder must engage securely.
242
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Technical data
Technical data
Basic vehicle data
Introduction
The details given in the vehicle's technical documentation always take prece-
dence over the details in the Owner's Manual.
The performance values listed were determined without performance-reduc-
ing equipment, e.g. air conditioning system.
The specified values have been determined in accordance with rules and under
conditions set out by legal or technical requirements for determining opera-
tional and technical data for motor vehicles.
The listed values are for the basic model without optional equipment.
Vehicle data
Fig. 294
Type plate
Type plate
The type plate
is located at the bottom of the B-pillar on the right-
hand driver's side.
The type plate contains the following data.
Vehicle manufacturers
Vehicle identification number (VIN)
Maximum permissible gross weight
Maximum permissible towed weight (towing vehicle and trailer)
1
2
3
4
Maximum permissible front axle load
Maximum permissible rear axle load
Vehicle identification number (VIN)
The vehicle identification number - VIN (vehicle body number) is stamped on
the right hand suspension strut dome in the engine compartment. This number
is also located on a sign on the lower left hand edge below the windscreen (to-
gether with a VIN bar code), together with a nameplate.
In Infotainment, the VIN number can also be displayed in the menu
→ →
Service.
Engine number
The engine number is embossed in the engine block.
Maximum permissible trailer weight
The listed maximum permissible trailer weight is only valid for altitudes up to
1000 m above sea level.
The engine output falls as altitude increases, as does the ability to climb.
Therefore, for every additional 1,000 m in height (or part), the maximum per-
missible towed weight must be reduced by 10 %.
The towed weight comprises the actual weights of the (loaded) towing vehicle
and the (loaded) trailer.
WARNING
Do not exceed the specified maximum permissible weights – risk of an ac-
cident and damage.
Operating weight
This value is only a guide value and corresponds to the lowest possible operat-
ing weight without further weight-reducing equipment (e.g. spare wheel etc.).
This includes 75 kg driver's weight, the weight of the operating fluids and the
on-board tool kit and a fuel tank filled to min. 90%.
Operating weight - Fabia
Engine
Gearbox
Operating weight (kg)
1.0 l/44 kW MPI
MG
1086
1.0 l/55 kW MPI
MG
1086
1.0 l/70 kW TSI
MG
1121
5
6
243
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Engine
Gearbox
Operating weight (kg)
1.0 l/81 kW TSI
MG
1132
DSG
1165
1.6 l/66 kW MPI
MG
1105
1.6 l/81 kW MPI
AG
1142
Operating weight - Fabia Combi
Engine
Gearbox
Operating weight (kg)
1.0 l/55 kW MPI
MG
1106
1.0 l/70 kW TSI
MG
1141
1.0 l/81 kW TSI
MG
1152
DSG
1185
1.6 l/66 kW MPI
MG
1125
1.6 l/81 kW MPI
AG
1162
Note
If required, you can find out the precise weight of your vehicle by contacting a
specialist garage.
Payload
It is possible to calculate the approximate loading capacity from the difference
between the permissible total weight and the operating weight.
The payload consists of the following weights.
▶
The weight of the passengers.
▶
The weight of all items of luggage and other loads.
▶
The weight of the roof, including the roof rack system.
▶
The weight of the equipment that is excluded from the operating weight.
▶
Trailer bearing load for trailer towing
measurement of fuel consumption and CO
2
emissions according to
ECE Regulations and EU Directives
The data on fuel consumption and CO
2
emissions were not available at the
time of going to press.
The valid specifications for your vehicle can be found in the technical vehicle
documentation (e.g. vehicle approval documentation, the COC document) or
at a ŠKODA partner.
Note
■
The emission and fuel consumption values have been determined in accord-
ance with rules and under conditions set out by legal or technical requirements
for determining operational and technical data for motor vehicles.
■
Depending on the range of equipment, style of driving, traffic situation,
weather influences and vehicle condition, consumption values may deviate
from the indicated values.
244
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Dimensions
Fig. 295 Vehicle dimensions
The vehicle dimensions given in the vehicle's technical documentation always take precedence over the details in the Owner's Manual.
The dimensions listed below are for the basic model without any optional equipment.
Vehicle dimensions by operating weight without driver (in mm)
Specification
Fabia
Fabia Combi
A
Height
1467
1467
B
Front track
Basic dimension
1463
1463
Vehicles with 1.0 l/81 kW TSI engine
1457
1457
C
Width
1732
1732
D
Rear track
Basic dimension
1457
1457
Vehicles with 1.0 l/81 kW TSI engine
1451
1451
E
Width including exterior mirrors
1958
1958
F
Clearance
133
135
G
Wheelbase
2470
2470
H
Length
3997
4262
245
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Departure angle
Fig. 296
Overhang angle
Angle
Overhang angle, front
Overhang angle, rear
The overhang angle values indicate the maximum incline of a slope, up which
the vehicle can drive at a slow speed without the bumper or underbody mak-
ing contact with the slope. The values listed correspond to the maximum axle
load, front or back.
Overhang angle (°)
Overhang angle, front
Overhang angle, rear
Fabia
Fabia Combi
Fabia
Fabia Combi
14.4
14.4
17.4
12.7
A
B
246
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle-specific details per engine type
Introduction
The specified values have been determined in accordance with rules and under conditions set out by legal or technical requirements for determining operational
and technical data for motor vehicles.
The exhaust gas standard is specified in the vehicle's technical documentation, as well as in the declaration of conformity (in so-called COC document). The
declaration of conformity (the so-called. COC document) can be obtained from a ŠKODA Partner (only valid for some countries and some models).
1.0 l/44 kW MPI engine
Output (kW at 1/min)
44/5000-6000
Maximum torque (Nm at rpm)
95/3000-4300
Number of cylinders/displacement (cm
3
)
3- 999
Body
Fabia
Gearbox
MG
Top speed (km/h)
with the mentioned gear engaged
157
(5)
Acceleration 0-100 km/h (s)
16.6
1.0 l/55 kW MPI engine
Output (kW at 1/min)
55- 6200
Maximum torque (Nm at rpm)
95/3000-4300
Number of cylinders/displacement (cm
3
)
3- 999
Body
Fabia
Fabia Combi
Transmission
MG
MG
Top speed (km/h)
with the mentioned gear engaged
168
(5)
169
(5)
Acceleration 0-100 km/h (s)
14.9
15.2
247
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
1.0 ltr./70 kW TSI engine
Output (kW at 1/min)
70/5000-5500
Maximum torque (Nm at rpm)
160/1500-3500
Number of cylinders/displacement (cm
3
)
3- 999
Body
Fabia
Fabia Combi
Transmission
MG
MG
Top speed (km/h)
with the mentioned gear engaged
184
(4)
185
(4)
Acceleration 0-100 km/h (s)
10.8
10.9
1.0 ltr./81 kW TSI engine
Output (kW at 1/min)
81/5000-5500
Maximum torque (Nm at rpm)
200/2000-3500
Number of cylinders/displacement (cm
3
)
3- 999
Body
Fabia
Fabia Combi
Gearbox
MG
DSG
MG
DSG
Top speed (km/h)
with the mentioned gear engaged
195
(5)
194
(6)
196
(5)
195
(6)
Acceleration 0-100 km/h (s)
9.6
10.1
9.7
10.2
1.6 l/66 kW MPI engine
Output (kW at 1/min)
66/4250-6000
Maximum torque (Nm at rpm)
155/3800-4000
Number of cylinders/displacement (cm
3
)
4- 1598
Body
Fabia
Fabia Combi
Transmission
MG
MG
Top speed (km/h)
with the mentioned gear engaged
180
(5)
182
(5)
Acceleration 0-100 km/h (s)
10.8
10.9
248
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
1.6 l/81 kW MPI engine
Output (kW at 1/min)
81- 5800
Maximum torque (Nm at rpm)
155/3800-4000
Number of cylinders/displacement (cm
3
)
4- 1598
Body
Fabia
Fabia Combi
Transmission
AG
AG
Top speed (km/h)
with the mentioned gear engaged
188
(5)
190
(5)
Acceleration 0-100 km/h (s)
11.1
11.3
249
Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст