Skoda Fabia (2019 year). Manual — part 14
label (sticker) can be replaced by setting the maximum value of the speed cat-
egory specified for the mounted tyres in Infotainment (only applies to certain
countries). This specification defines the maximum vehicle speed with moun-
ted all-season or “winter”tyres that may not be exceeded.
Snow chains
The snow chains improve handling in wintry road conditions.
Before fitting the snow chains, remove the full wheel trims.
Snow chains must only be fitted on the front wheels and are applicable only to
the following wheel / tyre combinations.
Rim size
Press depth D
Tyre size
5J x 14
35 mm
175/70 R14
Only fit snow chains with links and locks not larger than 9 mm.
Rim size
Press depth D
Tyre size
6J x 15
38 mm
185/60 R15
Only fit snow chains with links and locks not larger than 12 mm.
WARNING
Do not use chains on snow and ice-free routes - the handling would be im-
paired and there is a risk of damage to the tyres.
220
General Maintenance
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Do-it-yourself
Emergency equipment, and self-help
Emergency equipment
Placement of the first aid kit and warning triangle
Fig. 255
Placement of the first aid kit
and warning triangle - version 1
Fig. 256 Placing the first aid kit and the warning triangle - variant 2 /
release the warning triangle
The following information is for the first aid kit and warning triangle from the
ŠKODA Original accessories valid.
Placing the first-aid kit
The first-aid kit can be attached to the right-hand side of the boot using a
strap
Placing of the warning triangle - variant 1
The warning triangle can be stored in the recess under the loading edge
.
Position of the warning triangle - variant 2
The first-aid kit can be attached to the right-hand side of the boot using a
strap
.
›
To release, press the clasp on the strap in the direction of arrow
1
and fold
open the strap
A
in the direction of arrow
2
›
To secure, fold up the belt
A
against the arrow direction
2
until it locks in-
to place.
WARNING
Properly secure the first aid kit and the warning triangle, or there is a risk of
injury in the event of sudden braking or a vehicle collision.
Location of reflective vest
Fig. 257
Stowage compartment for the
reflective vest in the front door
The reflective vest can be stowed in the storage compartment
A
inside the
storage compartment of the front door
.
Fire extinguisher
Fig. 258
Release the fire extinguisher
The fire extinguisher is attached by two straps in a bracket under the front
passenger's seat.
221
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
›
To remove the fire extinguisher, release the safety catches on the two straps
in the direction of arrow
and remove the fire extinguisher.
›
To secure, place the fire extinguisher back in the mount and secure with the
belts.
The Owner´s Manual is fitted next to the fire extinguisher.
Pay attention to the expiration date of the fire extinguisher. After this date, the
correct function of the device is not guaranteed.
WARNING
Always properly secure the fire extinguisher, there is a risk of injury in the
event of sudden braking or a vehicle collision.
Vehicle tool kit
Fig. 259 Vehicle tool kit
The box containing the vehicle tool kit is located in the stowage compartment
for the spare wheel, and can be secured with a tape depending on the equip-
ment fitted.
Depending on the equipment, not all of the following components in the on-
board tool kit have to be contained in it.
Screwdriver
Top section for the anti-theft wheel bolts
Towing eye
Clamps for removing the wheel trims
1
2
3
4
Jack with sign
Wheel brace
Extraction pliers for the wheel bolt caps
Breakdown kit
WARNING
■
The factory-supplied lifting jack is only intended for your model of vehi-
cle. Under no circumstances attempt to lift other vehicles or loads with it –
there is a risk of injury.
■
Always stow the tool in the box securely and make sure that it is secured
to the spare wheel using the tape - there is a risk of injury in the event of
sudden braking or a vehicle collision.
CAUTION
Screw the jack back to its starting position prior to putting it back in its box –
Otherwise, there is a risk of damage to the box.
Note
The declaration of conformity is included with the jack or the log folder.
Changing a wheel
Preliminary work
For safety's sake, the following instructions must be observed before
changing a wheel on the road.
›
Park the vehicle as far as possible away from the traffic flow - choose a place
with a flat and firm surface.
›
Switch off the engine.
›
For vehicles with manual transmission select 1, gear.
›
For vehicles with automatic transmission, place the selector lever in the P
position.
›
Firmly apply the handbrake.
›
Switch on the hazard warning lights and set up the warning triangle at the
prescribed distance.
›
Have all the occupants get out. The passengers should not stand on the
road while the wheel is being changed (they should remain behind a crash
barrier, for instance).
›
Uncouple any trailers.
5
6
7
8
222
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Changing a wheel
›
Remove the spare wheel
›
Remove the full wheel trim
.
›
Loosen the wheel bolts
»
.
›
Jack up the vehicle
until the wheel that needs changing is clear of
the ground.
›
Unscrew the wheel bolts and place them on a clean surface (cloth, paper,
etc.).
›
Remove the wheel carefully.
›
Attach the spare wheel and slightly screw on the wheel bolts.
›
Lower the vehicle.
›
Tighten the wheel bolts opposite each other using the wheel wrench (“pull-
ing crossways”)
.
›
Replace the wheel trim
When fitting a wheel with directional tyres, ensure that the direction of rota-
tion is correct
.
All bolts must be clean and must turn easily. If screws are corroded and diffi-
cult to move, these must be replaced.
WARNING
■
Undo the wheel bolts just a little (about one turn), provided the vehicle
has not yet been jacked up. Otherwise the wheel could come loose and fall
off – risk of injury.
■
Under no circumstances must the bolts be greased or oiled - cause an ac-
cident.
Subsequent steps
After changing the wheel, the following work should be carried out.
›
Stow the replaced wheel in the well under the floor covering of the luggage
compartment and secure with a locking screw.
›
Stow the tool kit in the space provided and secure using the strap.
›
Check tyre pressure on the mounted wheel and adjust if necessary and, with
vehicles with tyre pressure monitoring, save the tyre pressure values in the
system
›
Have the tightening torque of the wheel bolts checked as soon as possible.
The prescribed tightening torque is 120 Nm.
Replace the damaged tyre. Repairing the tyre is not recommended.
WARNING
Tightening torque which is too high can damage the threads and this can
result in permanent deformation of the contact surfaces on the rim. Where
tightening torque is too low, the wheels may become loose while driving -
risk of accident. Therefore, drive cautiously and only at a moderate speed
until the tightening torque has been checked.
Removing/stowing the spare wheel
Fig. 260
Taking the wheel out
The spare wheel is located in a well under the floor covering in the luggage
compartment and is fixed in place with a fastening screw
Taking the wheel out
›
Lift up the floor in the luggage compartment.
›
Loosen the retaining belt and take out the box with the tool kit.
›
Unscrew the fastening screw in the direction of arrow
and the re-
move the wheel.
Stowing the wheel
›
Place the wheel into the wheel well with the wheel rim pointing downward.
›
Pull the fixing band through the opposite holes in the wheel rim.
›
Screw the fastening screw opposite to the direction of arrow until it stops
.
›
Place the box with the tool kit back inside the wheel and secure it with the
tape.
›
Fold back the floor in the luggage compartment.
223
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Full wheel trim
Remove trim
›
Hang the clamps for removing the full wheel trims at the edge of one of the
ventilation openings in the full wheel trim.
›
Push the wheel wrench through the clamp, support on the tyre and pull off
the wheel trim.
Install trim
›
Press the wheel trim onto the wheel rim at the designated valve opening.
›
Then press the trim into the wheel rim until its entire circumference latches
correctly into position.
The position of the anti-theft wheel bolt is indicated by means of a symbol on
the back of the wheel trim supplied ex-factory or from the ŠKODA Original
Accessories. If using the anti-theft wheel bolt it should be fitted at this point
»
.
WARNING
We recommend that you use wheel trims from ŠKODA Original Accesso-
ries. A sufficient air supply may not be able to be guaranteed with other
wheel trims to cool the braking system – Otherwise there is a risk of an ac-
cident.
CAUTION
■
If the wheel trim is positioned outside the position marked for the anti-theft
wheel bolt, there is a risk of damaging the wheel cover.
■
Use only manual pressure and do not hit the full wheel trim – otherwise there
is a risk of damaging the trim.
Note
We recommend that you use wheel trims from ŠKODA Original Accessories.
Wheel bolts
Fig. 261
Remove the cap
›
To remove the cap insert the extraction pliers as far as they will go on the
cap and pulling them out in the direction of arrow
›
To install, insert the cap onto the wheel bolt as far as it will go.
Anti-theft wheel bolts
Fig. 262
Anti-theft wheel bolt and at-
tachment
The anti-theft wheel bolts protect wheels from being stolen. This can only be
loosened/tightened with attachment
B
.
›
Insert the upper section
B
on the anti-theft wheel bolt
A
until it stops.
›
Insert the key as far as it will go onto attachment
B
and loosen / tighten the
wheel bolt.
›
Remove the attachment.
The attachment for the anti-theft wheel bolts must always be kept in the
vehicle in case of a possible wheel change!
For wheel trims supplied ex-factory or from ŠKODA Original Accessories, the
anti-theft wheel bolt should be installed in the position marked on the back of
the wheel trim.
224
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Note
We recommend that you retain the label with the code number. A replacement
upper section can be acquired from ŠKODA Original Parts based on this.
Loosening/tightening wheel bolts
Fig. 263
Loosening the wheel bolts
›
Insert the wheel wrench onto the wheel bolt to the stop. Use the associated
attachment for the anti-theft wheel bolts
›
To loosen the screws, grasp the key end and turn the screw about one turn
rotation in the direction of the arrow
›
To tighten the screws grasp the key end and turn the screw against the di-
rection of the arrow
, until it is tight.
WARNING
If it proves difficult to undo the bolts, carefully apply pressure to the end of
the wrench with your foot. Keep hold of the vehicle when doing so, and
make sure you keep your footing - danger of injury.
Raising the vehicle
Fig. 264
Jacking points for the jack
Fig. 265 Attach lifting jack
Before the vehicle is raised, please take note of the safety instructions
To lift the vehicle, us the jack from the tool kit. Position the jack at the jacking
point closest to the wheel to be replaced.
The jacking points are located on the lower sill
›
Position the base plate of the jack with its full area resting on level ground
and ensure that the jack will fit in the jacking point when raised
.
›
Use the crank to raise the jack until its pawl covers the jacking point
- .
›
Raise the vehicle until the wheel is a little off the floor.
WARNING
The following instructions must be observed, otherwise there is risk of in-
jury.
■
Ensure the vehicle cannot unexpectedly roll away.
■
Always ensure the base plate of the lifting jack cannot slip.
■
Place a wide and stable base material under the jack if on a loose surfa-
ces (e.g. gravel).
■
Place an anti-slip base material (e.g. a rubber mat) under the jack if on a
smooth surface (e.g. cobblestones).
■
Always raise the vehicle with the doors closed.
■
Never position any body parts (e.g. arms or legs) under the vehicle while
the vehicle is raised.
■
When the vehicle is raised, never start the engine.
225
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
It is important to ensure that the jack is correctly attached to the bar of the
lower beam – otherwise there is a risk of damage to the vehicle.
Breakdown kit
Introduction
The following information applies for the breakdown kit supplied ex-factory.
The breakdown kit can be used to seal punctures with a diameter of up to
about 4 mm.
A repair made using the breakdown kit is never intended to replace a perma-
nent repair on the tyre. Its purpose is to get you to the nearest specialist ga-
rage.
Replace the tyre that was repaired using the breakdown kit as soon as possi-
ble, or consult a specialist garage about repair options.
Do not remove foreign bodies which have penetrated into the tyre (e.g. nails).
Do not use the breakdown kit in the following cases.
▶
The rim is damaged.
▶
The outdoor temperature is below the minimum temperature indicated in
the instruction manual for the tyre filling bottle with sealant.
▶
Tyre punctures greater than 4 mm.
▶
Damage to the tyre wall.
▶
The use-by date (see inflation bottle) has passed.
WARNING
■
If there is skin contact with the sealant wash the affected area immedi-
ately.
■
Observe the instructions provided in the puncture repair kit manufactur-
er's instructions for use.
Description of the breakdown kit
Fig. 266 Description of the breakdown kit
Read and observe on page 226 first.
The kit is located in a box under the floor covering in the luggage compart-
ment.
Sticker with “max. 80 km/h”/“max. 50 mph” speed designation
Valve remover
Inflation hose with plug
Air compressor (the layout of the controls may be different depending on
the type of air compressor delivered with the vehicle)
Tyre inflation hose
Button for tyre pressure reduction
Tyre pressure indicator
12 volt cable connector
ON and OFF switch
Tyre inflator bottle with sealant
Replacement valve core
Note
The declaration of conformity is included with the air compressor or the log
folder.
1
2
3
4
5
6
7
8
9
10
11
226
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Preparing to use the breakdown kit
Read and observe on page 226 first.
For safety's sake, the following instructions must be observed before
undertaking a wheel repair on a road.
›
Park the vehicle as far as possible away from the traffic flow - choose a place
with a flat and firm surface.
›
Switch off the engine.
›
For vehicles with manual transmission select 1st gear.
›
For vehicles with automatic transmission, place the selector lever in the P
position.
›
Firmly apply the handbrake.
›
Switch on the hazard warning lights and set up the warning triangle at the
prescribed distance.
›
Have all the occupants get out. While the repair is being carried out, the
passengers should not stand on the road (instead they should remain behind
a crash barrier, for instance).
›
Uncouple any trailers.
Sealing and inflating tyres
Read and observe on page 226 first.
Sealing
›
Unscrew the valve cap from the damaged tyre.
›
Attach the valve remover
2
on page 226 onto the valve insert, so
that the valve insert fits into the slot of the valve remover.
›
Unscrew the valve insert and place it on a clean base (rag, paper etc.).
›
Forcefully shake bottle
10
several times.
›
Firmly screw the inflation hose
3
onto the tyre inflater bottle
10
. The film
on the bottle cap is pierced.
›
Remove the plug from the inflation hose
3
and insert the bottle onto the
tyre valve.
›
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
›
Remove the filler plug from the tyre valve.
›
Screw in the valve insert with the valve remover
2
.
Inflating
›
Screw the air compressor tyre inflation hose
5
ly onto the tyre valve.
›
For vehicles with manual transmission, set the lever in the neutral position.
›
On vehicles with automatic transmission, place the selector lever in the P
position.
›
Start the engine.
›
Plug the connector
8
into 12 volt socket
.
›
Switch on the air compressor with the ON and OFF switch
9
.
›
Once tyre inflation pressure of 2.0-2.5 bar has been reached, turn off the air
compressor. Observe the maximum running time of the air compressor ac-
cording to the instructions of the repair kit manufacturer
›
If you cannot reach an air pressure of 2.0 - 2.5 bar, unscrew the tyre inflation
hose
5
from the tyre valve.
›
Drive the vehicle 10 metres forwards or backwards to allow the sealing
agent to “distribute” in the tyre.
›
Firmly screw the tyre inflation hose
5
back onto the tyre valve and repeat
the inflation process.
›
Stick the corresponding sticker
1
onto the dashboard in the driver's field of
view.
At a tyre inflation pressure of 2.0–2.5 bar, the journey can be continued at a
maximum speed of 80 km/h or 50 mph.
WARNING
■
If the tire does not inflate to at least 2.0 bar, the damage is too great. The
sealing agent cannot be used to seal the tyre.
Do not drive the vehicle!
Seek help from a specialist garage.
■
The tyre inflation hose and air compressor may get hot while the tyre is
being inflated – there is a risk of injury.
CAUTION
Switch off the air compressor at the latest after the running time according to
the instructions of the repair kit manufacturer has elapsed – otherwise there is
the risk of compressor damage! Allow the air compressor to cool a few mi-
nutes before switching it on again.
227
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Information on driving with repaired tyres
Read and observe on page 226 first.
The filling pressure of the repaired tyre is a 10-minute test drive.
If the tyre pressure is 1.3 bar or less
›
You cannot properly seal the tyre using the breakdown kit.
Do not contin-
ue to drive! Seek help from a specialist garage.
If the tyre pressure is 1.3 bar or more
›
Set the tyre pressure back to the correct value
.
›
Continue driving carefully to the nearest specialist garage at a maximum
speed of 80 km/h (50 mph).
WARNING
A tyre filled with sealant has the same driving characteristics as a standard
tyre. The following guidelines must therefore be observed.
■
Do not drive faster than 80 km/h (50 mph).
■
Avoid accelerating at full throttle, sharp braking and fast cornering.
Jump-starting
Introduction
WARNING
■
The following instructions must be followed at all times when working on
the engine compartment
.
■
When handling the vehicle battery, the following warnings must be ob-
served
■
A discharged vehicle battery can freeze at temperatures just below 0 °C.
If the battery is frozen, do not carry out a jump start with the battery of
another vehicle – risk of explosion and injury!
■
Never jump-start vehicle batteries with an electrolyte level that is too low
– risk of explosion and caustic burns!
Jump-starting using the battery from another vehicle
Fig. 267 Jump-starting: - discharged battery, - power-supplying
battery/ground point of the engine for the START-STOP system
Read and observe on page 228 first.
If, because of a discharged battery, it is not possible to start the engine, the
battery of another vehicle can be used to start the engine. To do this, jump-
start cables are required which have a sufficiently large cross-section and insu-
lated terminal clamps.
The rated voltage of the two batteries must be 12 V. The capacity (Ah) of the
power-supplying battery must not be significantly lower than the capacity of
the discharged battery.
The jump-start cables must be attached in the following sequence.
›
Attach clamp
1
to the positive terminal of the discharged battery.
›
Attach clamp
2
to the positive terminal of the power-supplying battery.
›
Attach clamp
3
to the negative terminal of the power-supplying battery.
›
For vehicles with the START-STOP system, attach clamp
4
to the ground
point of the engine
A
.
›
For vehicles without the START-STOPsystem, attach clamp
4
to a solid
metal part firmly attached to the engine block or directly to the engine block.
Starting engine
›
Start the engine on the vehicle providing the power and allow it to idle.
›
Initiate the starting process in the vehicle with the discharged battery.
›
If the engine does not start within 10 s, then cancel the starting procedure
and repeat after half a minute.
›
Detach the jumper cables in the exact reverse order that they were attach-
ed.
228
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WARNING
■
Never clamp the jump cable to the negative terminal of the discharged
battery - risk of explosion.
■
The non-insulated parts of the terminal clamps must never touch each
other – risk of short circuit.
■
The jump-start cable connected to the positive terminal of the battery
must not come into contact with electrically conducting parts of the vehi-
cle – risk of short circuit.
■
Position the jump cables so that they cannot be caught in rotating parts in
the engine compartment - danger of injuries and the risk of vehicle dam-
age.
Towing the vehicle
Information about the towing process
Fig. 268 Braided tow ropes/spiral tow rope
To tow with a tow rope, use only a braided synthetic fibre rope
-
»
.
Attach the tow rope or the tow bar to the towing eyes at the front
, towing eyes at the rear
or to the towing device of the
trailer device
Conditions for towing.
Cars with automatic gearboxes must not be towed with the rear wheels
raised - there is a risk of gearbox damage!
If the gearbox has no oil, your vehicle must be towed with the front axle
raised clear of the ground or on a breakdown vehicle or trailer.
The maximum towing speed is 50 km/h.
The vehicle must be transported on a special breakdown vehicle or trailer
if it is not possible to tow the vehicle in the way described or if the towing
distance is greater than 50 km.
Driver of the tow vehicle
›
On vehicles with manual transmission, engage gear slowly when starting.
›
On vehicles with automatic transmission, accelerate with particular care.
›
Only then, approach correctly when the rope is taut.
Driver of the towed vehicle
›
If possible, the vehicle should be towed with the engine running. The brake
booster and power steering only operate if the engine is running, otherwise
much greater force has to be applied to the brake pedal and more power has
to be expended for steering.
›
If it is not possible to start the engine, switch on the ignition so that the
steering wheel does not lock and so that the turn signal lights, windscreen
wipers and windscreen washer system can be used.
›
Take the vehicle out of gear or move the selector lever into position N if the
vehicle is fitted with an automatic gearbox.
›
Keep the tow rope taut at all times during the towing procedure.
WARNING
■
Spiral tow ropes must not be used for towing
- , the towing
eye may unscrew out of the vehicle – risk of accident.
■
The tow rope should not be twisted - risk of accident.
CAUTION
■
Do not tow-start the engine – There is a risk of damaging the engine. The
battery from another vehicle can be used as a jump-start aid
■
For off-road towing manoeuvres, there is a risk to both vehicles that the fas-
teners may become overloaded and damaged.
Note
We recommend that you use a tow rope from ŠKODA Original Accessories.
229
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Front towing eye
Fig. 269 Remove cap / install towing eye
Cap removal/fitting
›
To remove, press down on the cap in the direction of arrow
1
and remove it
in the direction of arrow
2
.
›
To fit it, insert the cap in arrow range
1
and then press on the opposite edge
of the cap. The cap must engage firmly.
Removing/installing the towing eye
›
To fit, screw in the towing eye by hand in the direction of the arrow
3
›
Tighten the towing eye using a wheel wrench or similar object. To do this, in-
sert the wheel wrench through the eye.
›
To removeit, unscrew the towing eye in the opposite direction to arrow
3
.
WARNING
The towing eye must always be firmly in place, otherwise the towing eye
could break whilst being towed.
Towing eye rear
Fig. 270
Rear towing eye
The rear towing eye is located below the bumper on the right.
Vehicles with a tow hitch
For vehicles with a factory-fitted towing device, the pre-installed detachable
tow-bar may be used
Remote control and removable light - changing the battery
Introduction
CAUTION
■
The replacement battery/batteries must comply with the original specifica-
tion.
■
Pay attention to the correct polarity when changing the rechargeable batter-
ies.
Note
We recommend having the faulty battery/batteries replaced by a specialist ga-
rage.
230
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Key with fold-out key bit
Fig. 271 Opening the cover/removing the battery
Read and observe on page 230 first.
›
Pop out the key bit.
›
Press off the battery cover
A
with your thumb or by using a flat
screwdriver in region
B
.
›
Open the battery in the direction of the arrow
1
.
›
Remove the discharged battery in the direction of arrow
2.
›
Hold any button on the key for about 5 s.
›
Insert the new battery.
›
Insert the battery cover
A
and press it down until it clicks audibly into place.
The key has to be synchronised if the vehicle cannot be unlocked or locked
with the key after replacing the battery
.
Removable light
Fig. 272
Locking clip on the battery cov-
er
Read and observe on page 230 first.
›
Lever off the cover for the rechargeable batteries with a narrow and pointed
object from the area of the lock clips
A
.
›
Replace the batteries.
›
Insert the cover for the rechargeable batteries and press it down until it
clicks into place.
CAUTION
If an incorrect battery type is used or a non-rechargeable battery, there is a
risk of damaging the light and the vehicle's electrical system.
Emergency unlocking/locking of doors
Unlocking/locking the front left door
Fig. 273 Door handle: Open lock cover / lock cylinder with key
The door can be emergency unlocked / emergency locked using the key via
the lock cylinder.
›
Pull on the door handle and hold.
›
Insert the key into the recess on the lower side of the cover and fold up the
cover in the direction of arrow
.
›
Release the door handle.
›
Insert the key with the fold-out key bit with the buttons facing upwards
into the lock cylinder and unlock/lock the vehicle.
›
Pull on the door handle and hold.
›
Replace the cover.
231
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
Make sure you do not damage the paint when performing an emergency lock-
ing/unlocking.
Locking the door without locking cylinders
Fig. 274 Left door/right door:
›
Open the corresponding door.
›
In vehicles with the panel
A
, remove this panel
.
›
Insert the key into the slot and turn in the direction of the arrow (spring-loa-
ded position).
›
Replace the cover
A
.
After closing, the door is locked.
Unlocking the boot lid
Fig. 275
Unlocking the door
The boot lid can be unlocked manually from inside the vehicle.
›
Insert a screwdriver or similar tool into the opening in the trim
far as the latch.
›
Unlock the lid by moving it in the direction of the arrow.
Selector lever emergency unlocking
Fig. 276 Remove / release the selector lever
›
Firmly apply the handbrake.
›
Insert a flat-head screwdriver or similar tool into the gap in the arrow area
1
and carefully lift the cover in arrow direction
2
.
›
Likewise lift the cover with your hand as well.
›
Press on the yellow plastic part in the direction of arrow
3
, simultaneously
press the lock button in the selector lever handle and put the lever in position
N.
If the selector lever is moved again to position P, it is once again blocked.
CAUTION
Make sure when lifting not to damage cover parts by the screwdriver in the
shift lever environment.
Replacing windscreen wiper blades
Introduction
WARNING
Replace the windscreen wiper blades once or twice a year for safety rea-
sons.
232
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Replacing the windscreen wiper blades
Fig. 277
Setting the service position for
the wiper arms
Fig. 278 Changing the front windscreen wiper blade
Read and observe on page 232 first.
Before replacing the windscreen wiper blades, close the bonnet and put the
windscreen wiper arms into the service position.
Setting the service position
›
Switch the ignition on and off again.
›
Push the lever in the direction of arrow
for approximately 2 seconds.
Removing the wiper blade
›
Lift the wiper arm from the window in the direction of the arrow
1
.
›
Tilt the wiper blade to the stop in the same direction.
›
Grip the wiper arm and press securing latch
A
down in the direction of ar-
row
2
.
›
Remove the wiper blade in the direction of the arrow
3
.
Attaching the windscreen wiper blade
›
Slide the windscreen wiper blade in the opposite direction to arrow
3
until
it locks into place. Check that the windscreen wiper blade is correctly attach-
ed.
›
Fold the windscreen wiper arm back to the windscreen.
›
Turn on the ignition and press the lever in the direction of the arrow
Move the windscreen wiper arms into the home position.
Replacing the rear window wiper blade
Fig. 279 Changing the rear window wiper blade
Read and observe on page 232 first.
Removing the wiper blade
›
Lift the wiper arm from the windscreen in the direction of arrow
1
.
›
Tilt the wiper blade to the stop in the same direction.
›
Grip the wiper arm and press securing latch
A
down in the direction of ar-
row
2
.
›
Remove the wiper blade in the direction of the arrow
3
.
Attaching the windscreen wiper blade
›
Slide the windscreen wiper blade in the opposite direction to arrow
3
until
it locks into place. Check that the windscreen wiper blade is correctly attach-
ed.
›
Fold the windscreen wiper arm back to the windscreen.
233
Emergency equipment, and self-help
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fuses and light bulbs
Fuses
Introduction
Fig. 280
Blown fuse
Individual electrical circuits are protected by fuses. A blown fuse is recognisa-
ble by the molten metal strip
WARNING
Always read and observe the warnings before completing any work in the
engine compartment
CAUTION
■
Replace the faulty fuse with a new one of the same amperage.
■
If a newly inserted fuse again blows after a short time, then seek assistance
from a specialist garage.
■
“Do not repair” the fuses and do not replace them with stronger fuses - dan-
ger of fire and damage to another electrical system.
Note
■
We recommend always carrying replacement fuses in the vehicle.
■
One fuse may cover several consumers. A single consumer may use several
fuses.
Fuses in the dashboard
Fig. 281
Remove the cover
Read and observe and on page 234 first.
The fuses are located on the bottom of the dash panel behind a cover.
Replacing fuses
›
Remove the ignition key, turn off the lights and all electrical consumers.
›
Remove the cover of the fuse box
in the direction of the arrow.
›
Remove the plastic clip from the holder in the fuse box cover.
›
Use the clip to pull the fuse out, then insert a new fuse.
›
Replace the clamp in the original position.
›
Insert the top edge of the cover into the dash panel first.
›
Push the lower edge of the cover in the region
A
.
234
Do-it-yourself
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fuse assignment in the dashboard
Fig. 282
Fuses: LHD /
- RHD
Read and observe and on page 234 first.
No.
Power consumer
1
Left parking light, parking light, high-mounted brake light
2
Central locking, front and rear window washer system (only with
ACC)
3
Ignition
4
Right-hand light, rear fog light, license plate light
5
Power windows - driver
6
Interior lighting
7
Horn
8
Tow hitch
9
Operating lever beneath the steering wheel, engine control unit (only
without KESSY), automatic gearbox (only without KESSY), selector
lever of the automatic transmission (only without KESSY), ESC (only
without KESSY), towing equipment (only without KESSY), power
steering (only without KESSY)
10
Power windows - rear left
11
Headlight cleaning system
No.
Power consumer
12
Infotainment screen
13
12 volt socket in luggage compartment
14
Operating lever under the steering wheel, light switch, ignition key
removal lock (automatic transmission), diagnostic connector, head-
light flasher, rain sensor, light sensor, reversing camera
15
Air conditioning, automatic transmission
16
Instrument cluster, emergency call
17
Anti-theft alarm, horn
18
Databus
19
Not assigned
20
Not assigned
21
Not assigned
22
Front and rear windshield washer (only without ACC)
23
Not assigned
24
Blower fan for the air conditioning system, heating, air conditioning,
heating
25
Not assigned
26
Heated front seats
27
Rear window wiper
28
Not assigned
29
airbag
30
Light switches, reversing light switch, exterior mirrors, feed for the
central toolbar, feed for the side toolbar, rear view mirror, air-condi-
tioning system, park assist
31
Fuel pump, radiator fan, cruise control, front and rear window wash-
er, engine start
32
Diagnostics connection, headlamp leveling, washing nozzle heating,
LED headlights
33
Clutch pedal switch
34
USB charge function
35
“Blind spot” detection
36
Heated front seats
235
Fuses and light bulbs
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст