Infiniti M35/M45 Y50. Manual — part 815
SIDE WINDOW GLASS
GW-57
C
D
E
F
G
H
J
K
L
M
A
B
GW
SIDE WINDOW GLASS
PFP:83300
Removal and Installation
NIS00226
REMOVAL
1.
Remove the rear pillar finisher. Refer to .
2.
Remove the headlining. Refer to
.
3.
Apply protective tape around the side window to protect the painted surface from damage.
4.
Remove the side window glass using piano wire or power cutting tool and an inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
PIIB3285J
1.
Side window glass
2.
Adhesive
3.
Primer
4.
Body side outer panel
GW-58
SIDE WINDOW GLASS
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.
●
The molding must be installed securely so that it is in position and leaves no gap.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the side window in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
REAR WINDOW GLASS AND MOLDING
GW-59
C
D
E
F
G
H
J
K
L
M
A
B
GW
REAR WINDOW GLASS AND MOLDING
PFP:79712
Removal and Installation
NIS00227
REMOVAL
1.
Remove rear seatback and rear seat cushion. Refer to
.
2.
Remove the rear pillar finisher. Refer to
3.
Remove the rear parcel shelf finisher. Refer to
EI-42, "REAR PARCEL SHELF FINISHER"
4.
Remove the rear of the headlining. Refer to
5.
Remove the connectors and grounds for the rear window defogger and printed antenna.
6.
Remove the roof side molding. Refer to
.
1.
Roof side molding
2.
Rear window molding (upper)
3.
Rear window molding (lower)
4.
Rear window glass
5.
Dam rubber
6.
Spacer
7.
Adhesive
8.
Primer
9.
Rivet
10. Fastener
11.
Roof panel
12. Trunk lid outer panel
PIIB3286J
GW-60
REAR WINDOW GLASS AND MOLDING
7.
After removing molding using pliers, remove glass using piano wire or power cutting tool A and an inflat-
able pump bag B.
8.
Remove the rear window glass, using suction lifter.
NOTE:
If a rear window glass is reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
●
When a rear window glass is reused, do not use a cutting knife or power cutting tool.
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
●
The dam rubber should be installed in position.
●
Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
●
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger compartment air pressure when a door is closed.
●
The molding must be installed securely so that it is in position and leaves no gap.
●
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive are flammable.
●
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
●
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the rear window in case of an accident.
CAUTION:
●
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Do not leave primers or adhesive cartridge unattended with their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
PIIB5779E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст