Infiniti M35/M45 Y50. Manual — part 816
FRONT DOOR GLASS AND REGULATOR
GW-61
C
D
E
F
G
H
J
K
L
M
A
B
GW
FRONT DOOR GLASS AND REGULATOR
PFP:80300
Removal and Installation
NIS00228
DOOR GLASS
Removal
1.
Remove the front door finisher. Refer to
.
2.
Remove the front door sash cover inner. Refer to
EI-36, "FRONT DOOR SASH COVER INNER"
3.
Operate the power window main switch to raise/lower the door
window until the glass mounting bolts can be seen.
4.
Remove the glass mounting bolts.
1. Door glass
2.
Module assembly
3.
Power window motor
4.
Regulator assembly
5.
Door glass run
PIIB3287J
PIIB3288J
GW-62
FRONT DOOR GLASS AND REGULATOR
5.
While holding the door glass, raise it at the rear end to pull the
glass out of the sash toward the inside of the door.
Installation
Install in the reverse order of removal.
REGULATOR ASSEMBLY
Removal
1.
Remove the front door finisher. Refer to
2.
Operate the power window main switch to raise/lower the door
window until the glass mounting bolts can be seen.
3.
Remove the glass mounting bolts.
4.
Raise up the door glass and hold with a suction lifter A.
5.
Remove the mounting bolts, and remove the module assembly.
6.
Disconnect the harness connector for the module assembly, and unclip the harness from the inside.
Installation
Install in the reverse order of removal.
SIIA1779J
PIIB3288J
PIIB3510J
FRONT DOOR GLASS AND REGULATOR
GW-63
C
D
E
F
G
H
J
K
L
M
A
B
GW
Inspection after Removal
Check the regulator assembly for the following items. If a malfunc-
tion is detected, replace or grease it.
●
Wire wear
●
Regulator deformation
●
Grease condition for each sliding part
The arrows in the figure show the application points of the multi-pur-
pose grease.
Disassembly and Assembly
NIS00229
REGULATOR ASSEMBLY
Disassembly
1.
Remove power window motor from module assembly.
2.
Remove regulator assembly from module assembly.
Assembly
Assemble in the reverse order of disassembly.
Inspection after Installation
NIS0022A
SYSTEM INITIALIZATION
If any of the following work has been done, initialize the system.
●
Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting bat-
tery cable, etc.
●
Removal and installation of the regulator assembly.
●
Removal and installation of the motor from the regulator assembly.
●
Removal and installation of the harness connector of the power window switch.
●
Operate the regulator assembly as a unit.
●
Removal and installation of the door glass.
●
Removal and installation of the door glass run.
Initialization
After installing each component to the vehicle, follow the steps below.
1.
Disconnect the minus terminal of battery or disconnect power window switch's harness connector tempo-
rarily, then reconnect after at least 1 minute.
2.
Turn ignition switch ON.
3.
Open the window to its full width by operating the power window switch. (Exclude this pocedure if the win-
dow is already fully opened)
4.
Fully draw the power window switch in up direction (auto close position) and hold, keep holding the switch
even when window is completely closed and then release afeter 3 second has passed.
5.
Inspection of the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation.In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM.
1.
Fully open the door glass.
2.
Place a wooden piece (wooden hammer handle etc.) at near fully closed position.
3.
Carry out fully closing operation with auto up switch.
●
Check that the glass reverses without pinching the wooden piece, is lowered approx.150 mm (5.91 in) or
for 2 seconds and then stops.
●
The glass should not be raised with power window main switch operated while it is reversing or lowering.
PIIB3290J
GW-64
FRONT DOOR GLASS AND REGULATOR
CAUTION:
●
Do not inspect with pinching a part of worker's body, a hand etc. Work carefully not to be pinched.
●
Check that auto up function is normal before inspection following the system initialization.
FITTING INSPECTION
●
Make sure the glass is securely fit into the glass run groove.
●
Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)] and make sure the clearance to the sash is
parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass and guide rail mounting bolts to correct the glass position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст