Infiniti M35/M45 Y50. Manual — part 111
ASSEMBLY
AT-367
D
E
F
G
H
I
J
K
L
M
A
B
AT
13. Securely fasten revolution sensor harness with terminal clip.
14. Pull down A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
15. Install snap ring to A/T assembly harness connector.
16. Install magnets in oil pan.
17. Install oil pan, oil pan gasket and clips (VQ35DE models) or oil pan, oil pan gasket, brackets and clips
(VK45DE models) according to the following procedures.
a.
VQ35DE models
i.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
SCIA7526E
SCIA5299E
SCIA5300E
SCIA5200E
AT-368
ASSEMBLY
ii.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
: Front
: Bolt (22)
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
iii.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque. Refer to
CAUTION:
Do not reuse oil pan mounting bolts.
b.
VK45DE models
i.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
ii.
Install oil pan (3) (with oil pan gasket), clips (1) and brackets (2)
to transmission case.
: Front
: Bolt (22)
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
●
Be careful with installation direction of brackets (2).
iii.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque. Refer to
CAUTION:
Do not reuse oil pan mounting bolts.
18. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
19. Install torque converter.
SCIA8039E
SCIA4113E
SCIA8035E
SCIA4113E
ASSEMBLY
AT-369
D
E
F
G
H
I
J
K
L
M
A
B
AT
a.
Pour ATF into torque converter.
●
Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is
required for a new torque converter.
●
When reusing old torque converter, add the same amount
of ATF as was drained.
b.
Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
c.
Measure distance “A” to make sure that torque converter is in
proper position.
SAT428DA
SCIA5010E
Distance “A”
VQ35DE models:
25.0 mm (0.98 in) or more
VK45DE models:
22.0 mm (0.87 in) or more
SCIA5694E
AT-370
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
NCS001RD
*1: Refer to
MA-12, "Fluids and Lubricants"
Vehicle Speed at Which Gear Shifting Occurs
NCS001RE
2WD MODELS
●
At half throttle, the accelerator opening is 4/8 of the full opening.
●
At half throttle, the accelerator opening is 4/8 of the full opening.
AWD MODELS
●
At half throttle, the accelerator opening is 4/8 of the full opening.
Applied model
VQ35DE engine
VK45DE engine
2WD
AWD
2WD
Automatic transmission model
RE5R05A
Transmission model code number
98X1D, 98X6C
98X1C, 98X6D
95X7A
Stall torque ratio
1.74: 1
1.87: 1
Transmission gear ratio
1st
3.842
3.827
2nd
2.353
2.368
3rd
1.529
1.519
4th
1.000
1.000
5th
0.839
0.834
Reverse
2.765
2.613
Recommended fluid
Genuine NISSAN Matic J ATF*1
Fluid capacity
10.3 liter (10-7/8 US qt, 9-1/8 Imp qt)
CAUTION:
●
Use only Genuine NISSAN Matic J ATF. Do not mix with other fluid.
●
Using ATF other than Genuine NISSAN Matic J ATF will deteriorate in driveability and A/T durability, and may damage the
A/T, which is not covered by the warranty.
Engine model
VQ35DE
Throttle position
Vehicle speed km/h (MPH)
D
1
→
D
2
D
2
→
D
3
D
3
→
D
4
D
4
→
D
5
D
5
→
D
4
D
4
→
D
3
D
3
→
D
2
D
2
→
D
1
Full throttle
52 - 56
(32 - 35)
85 - 93
(53 - 58)
126 - 136
(78 - 85)
195 - 205
(121 - 127)
191 - 201
(119 - 125)
113- 123
(70 - 76)
70 - 78
(44 - 48)
28 - 32
(17 - 20)
Half throttle
42 - 46
(26 - 29)
70 - 76
(44 - 47)
107 - 115
(67 - 71)
140 - 148
(87 - 92)
111 - 119
(69 - 74)
67 - 75
(42 - 47)
35 - 41
(22 - 25)
11 - 15
(7 - 9)
Engine model
VK45DE
Throttle position
Vehicle speed km/h (MPH)
D
1
→
D
2
D
2
→
D
3
D
3
→
D
4
D
4
→
D
5
D
5
→
D
4
D
4
→
D
3
D
3
→
D
2
D
2
→
D
1
Full throttle
56 - 60
(35 - 37)
89 - 97
(55 - 60)
121 - 131
(75 - 81)
206 - 216
(128 - 134)
202 - 212
(126 - 132)
121 - 131
(75 - 81)
73 - 81
(45 - 50)
30 - 34
(19 - 21)
Half throttle
48 - 52
(30 - 32)
82 - 88
(51 - 55)
126 - 134
(78 - 83)
155 - 163
(96 - 101)
128 - 136
(80 - 85)
70 - 78
(43 - 48)
29 - 35
(18 - 22)
9 - 13
(6 - 8)
Engine model
VQ35DE
Throttle position
Vehicle speed km/h (MPH)
D
1
→
D
2
D
2
→
D
3
D
3
→
D
4
D
4
→
D
5
D
5
→
D
4
D
4
→
D
3
D
3
→
D
2
D
2
→
D
1
Full throttle
50 - 54
(31 - 34)
81 - 89
(50 - 55)
120 - 130
(75 - 81)
187 - 197
(116 - 122)
183 - 193
(114 - 120)
108 - 118
(67 - 73)
66 - 74
(41 - 46)
27 - 31
(17 - 19)
Half throttle
40 - 44
(25 - 27)
67 - 73
(42 - 45)
102 - 110
(63 - 68)
133 - 141
(83 - 88)
106 - 114
(66 - 71)
64 - 72
(40 - 45)
33 - 39
(21 - 24)
11 - 15
(7 - 9)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст