Infiniti M35/M45 Y50. Manual — part 1107
DRIVER AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
M
A
B
SRS
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Fix the air bag module harness (shown as A in the figure) to
the harness fixing hook (shown as B in the figure).
●
Be careful not to damage the harness while installing.
●
Tighten the special bolts after exactly adjusting the centers of fixing holes on the air bag module
side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged and the
module is not installed securely.
●
After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
●
In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSOULT–II.
●
In case that malunction is still detected after the above operation, peform self-diagnosis to repair
malfunctions. Refer to
PHIA0885J
SRS-44
SPIRAL CABLE
SPIRAL CABLE
PFP:25554
Removal and Installation
NHS0009D
REMOVAL
CAUTION:
●
Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.
●
Do not use air tools or electric tools for servicing.
●
Do not disassemble the spiral cable.
●
Do not arrow oil, grease, detergent or water to come in contact with the spiral cable.
●
Do not make an impact to the spiral cable by dropping etc. Replace the spiral cable if it has been
dropped or sustained an impact.
1.
Remove the air bag module. Refer to
SRS-42, "Removal and Installation"
.
2.
Remove the steering wheel. Refer to
PS-12, "Removal and Installation"
3.
Remove the column cover.
4.
Remove the wiper washer switch, then remove light and turn signal switch from the spiral cable.
5.
Remove the spiral cable.
●
Disconnect the horn switch connector (shown as A in the fig-
ure).
●
Disconnect the spiral cable connector (shown as B in the fig-
ure).
●
Loosen the spiral cable fixing screws.
●
Shift the spiral cable forward a bit while pushing the pawl
located above the spiral cable.
●
Disconnect the steering wheel switch connector (shown as C
in the figure).
NOTE:
Disconnect the spiral cable connector after disconnecting the
horn switch connector.
INSTALLATION
Install in the reverse order of removal.
PHIA1112E
1.
Steering wheel
2.
Steering column cover (lower)
3.
Light and turn signalswitchs
4.
Wiper washer switch
5.
Spiral cable
6.
Steering column cover (upper)
7.
Steering column assembly
8.
Driver air bag module connector
PHIA0886J
SPIRAL CABLE
SRS-45
C
D
E
F
G
I
J
K
L
M
A
B
SRS
CAUTION:
●
The spiral cable may snap by steering operation if the cable
is installed in an improper position.
●
The neutral position is set as follows.
Turn quietly the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and harf turns) and
stop turning at the point on which the stopper insertion
holes are in the same position.
The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper
is removed.
●
Do not turn the spiral cable rashly and also beyond the limit
number of turns. (These will cause cable snap.)
●
Adjust the spiral cable locating pin (showed as A inthe fig-
ure) to the steering wheel locating pin hole (showed as C in
the figuer).
●
Secure the air bag harness with the harness fixing hook.
●
After the work is completed, make sure no system malfunc-
tion is detected by air bag warning lamp.
●
In case that malfunction is detected by the air bag warning
lamp, reset by the self-diagnosis function and delete the
memory by CONSULT
−
II.
●
In case that malfunction is still detected after the above
operation, perform self-diagnosis to repair malfunctions.
Refer to
PHIA0887J
SRS-46
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
PFP:K8515
Removal and Installation
NHS0009E
REMOVAL
CAUTION:
●
Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at
least 3 minutes.
●
Do not use air tools or electric tools for servicing.
●
Always work from the side of air bag module. Do not work from the front of it.
●
Always place air bag module with pad side facing upward.
●
Do not use old fixing bolts after removal; replace with new bolts.
●
Do not make an impact to the air bag module by dropping etc. Replace the air bag module if it has
been dropped or sustained an impact.
1.
Remove the instrument panel & pad assemblies. Refer to
NOTE:
The figure shows installed condition of the front passenger air
bag module. (Under view of the module installed without glove
box cover.)
2.
Remove the front passenger air bag module from the instrument panel & pad assemblies.
●
Remove the 2 screws.
●
Remove the air bag from the rear side hook. (
shows the
backward direction of the vehicle.)
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Be careful not to damage the harness while installing.
●
After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
●
In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSOULT
−
II.
●
In case that malfunction is still detected after the above operation, peform self-diagnosis to repair
malfunctions. Refer to
.
Passenger air bag module connector-A
Passenger air bag module fixing bolt-B
Fixing bolt
:
24.5 N·m (2.5 kg
−
m, 18 ft
−
lb)
PHIA0868J
PHIA0888J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст