Infiniti M35/M45 Y50. Manual — part 1108
SIDE CURTAIN AIR BAG MODULE
SRS-47
C
D
E
F
G
I
J
K
L
M
A
B
SRS
SIDE CURTAIN AIR BAG MODULE
PFP:985P0
Removal and Installation
NHS0009F
REMOVAL
CAUTION:
●
Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.
●
Do not use air tools or electric tools for servicing.
●
Leave the curtain air bag module with air bag deployment side facing upward.
●
Do not make an impact to the air bag module by dropping etc. Replace the air bag module if it has
been dropped or sustained an impact.
1.
Remove the curtain air bag module.
●
Remove the headlining. Refer to
●
Remove the side curtain air bag module connector.
NOTE:
●
For installing / removing side curtain air bag module con-
nector, insert thin screwdriver wrapped in tape into notch,
lift lock and remove connector.
●
Install connector with lock raised, and push lock into con-
nector.
●
After installing the connector, make sure that the lock is
pushed securely into it.
●
Remove the curtain air bag module fixing bolts, then remove the ground bolt.
PHIA1115E
1.
Side curtain air bag module
A
Ground bolt
PHIA0953J
Fixing bolt (
)
:
10.8 N·m (1.1 kg
−
m, 8 ft
−
lb)
Ground bolt A
:
10.8 N·m (1.1 kg
−
m, 8 ft
−
lb)
SRS-48
SIDE CURTAIN AIR BAG MODULE
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Be careful not to damage the air bag harness.
●
After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
●
In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT-ll.
●
In case that malfunction is still detected after the avove operation, perform self-diagnosis to repair
malfunctions. Refer to
.
CRASH ZONE SENSOR
SRS-49
C
D
E
F
G
I
J
K
L
M
A
B
SRS
CRASH ZONE SENSOR
PFP:98531
Removal and Installation
NHS0009G
REMOVAL
CAUTION:
●
Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.
●
Do not use air tools or electric tools for servicing.
●
Do not use old fixing nuts after removal; replace with new nuts.
●
Do not make an impact to the crash zone sensor by dropping etc. Replace the crash zone sensor if
it has been dropped or sustained an impact.
●
Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger
air bag.
1.
Remove the crash zone sensor.
●
Remove the front grille. Refer to
EI-16, "Removal and Installation"
.
●
Remove the crash zone sensor fixing nuts.
●
Disconnect the crash zone sensor harness connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Be careful not to damage the crash zone sensor harness.
●
After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
●
In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT
−
ll.
●
In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
malfunctions. Refer to
Fixing nut
:
10.8 N·m (1.1 kg
−
m, 8 ft
−
lb)
PHIA1116E
SRS-50
SIDE AIR BAG (SATELLITE) SENSOR
SIDE AIR BAG (SATELLITE) SENSOR
PFP:98830
Removal and Installation
NHS0009H
REMOVAL
CAUTION:
●
Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3
minutes.
●
Do not use air tools or electric tools for servicing.
●
Do not use old fixing nuts after removal; replace with new nuts.
●
Do not make an impact to the side air bag (satellite) sensor by dropping etc. Replace the side air
bag (satellite) sensor if it has been dropped or sustained an impact.
●
Replace the satellite sensor of deployed SRS front side air bag and deployed SRS side curtain air
bag.
1.
Remove the side air bag (Satellite) sensor.
●
Remove front seat belt. Refer to
SB-29, "Removal and Installation of Front Seat Belt"
●
Remove fixing nuts, then remove side air bag (Satellite) sen-
sor.
●
Disconnect the side air bag (Satellite) sensor harness con-
nector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Be careful not to damage the satellite sensor harness.
●
After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
●
In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT
−
ll.
●
In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
malfunctions. Refer to
.
Fixing nut
:
10.8 N·m (1.1 kg
−
m, 8 ft
−
lb)
PHIA0902J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст