Infiniti M35/M45 Y50. Manual — part 284
TRUNK LID
BL-205
C
D
E
F
G
H
J
K
L
M
A
B
BL
Removal and Installation of Trunk Lid Striker
NIS001ZL
REMOVAL
1.
Remove the trunk rear plate and trunk rear finisher. Refer to
56, "Removal and Installation for Trunk Room Trim"
2.
Remove the mounting bolts, and remove the striker from the
trunk lock support.
INSTALLATION
1.
Install in the reverse order of removal.
2.
After installing, close the trunk lid height. Perform the lock and surface height adjustment. Refer to
3.
After installing, check the operation.
PIIB3914J
BL-206
TRUNK LID
Removal and Installation of Trunk Lid Weatherstrip
NIS001ZM
REMOVAL
Pull up and remove engagement with body from weatherstrip joint.
CAUTION:
After removal, do not pull strongly on the weatherstrip.
INSTALLATION
1.
Working from the lower section, align the weatherstrip seam with center of the striker and weatherstrip
onto the vehicle.
2.
After installation, pull the weatherstrip gently to ensure that there is no loose section.
NOTE:
Make sure the weatherstrip is fit tightly at each corner and back door rear plate.
1.
Weatherstrip
2.
Seam
PIIB3898J
TRUNK LID OPENER
BL-207
C
D
E
F
G
H
J
K
L
M
A
B
BL
TRUNK LID OPENER
PFP:84640
Component Parts and Harness Connector Location
NIS001ZN
1.
Fuse block (J / B) fuse layout
2.
Fuse and fusible link box
3.
BCM M1, M2, M3 (View with instru-
ment lower panel RH removed)
4.
Intelligent key unit M32 (View with
dash side finisher LH removed)
5.
Unified meter and A / C AMP M65
6.
Trunk lid opener switch M25
7.
Trunk lid lock assembly T106
(Trunk lid opener actuator)
8.
Trunk lid opener cancel switch M99
(Glove box inside)
PIIB5916E
BL-208
TRUNK LID OPENER
System Description
NIS001ZO
Power is supplied at all times
●
through 50A fusible link (letter F, located in the fuse and fusible link box)
●
to BCM terminal 55,
●
through 10A fuse [No.21, located in the fuse block (J/B)]
●
to BCM terminal 42.
Ground is supplied
●
to BCM terminal 52
●
through body grounds M16 and M70.
When trunk lid opener cancel switch is ON and trunk lid opener switch is ON (pushed)
Ground is supplied
●
to BCM terminal 30
●
through trunk lid opener switch terminals 1and 2
●
through trunk lid opener cancel switch terminals 1and 3 and
●
through body grounds M16 and M70.
And power is supplied
●
through BCM terminal 68
●
to trunk lid opener actuator terminal 3.
Ground is supplied
●
to trunk lid opener actuator terminal 2
●
through body grounds B402,B405.
Then BCM open trunk lid opener actuator.
TRUNK LID OPENER OPERATION
When trunk lid opener switch or trunk button of Intelligent Key is ON, BCM opens trunk opener actuator.
BCM can open trunk lid opener actuator when
●
vehicle speed is less than 5 km/h (3MPH)
●
vehicle security system is disarmed or pre-armed phase
BCM does not open trunk lid opener actuator when
●
trunk lid opener cancel switch is OFF (CANSEL)
●
vehicle speed is more than 5 km/h (3MPH)
●
vehicle security system is armed or alarm phase
●
Intelligent Key is inserted in key slot
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст