Infiniti M35/M45 Y50. Manual — part 238
RADIATOR CORE SUPPORT
BL-21
C
D
E
F
G
H
J
K
L
M
A
B
BL
RADIATOR CORE SUPPORT
PFP:62500
Removal and Installation
NIS001WN
REMOVAL
1.
Remove front bumper, bumper reinforcement. Refer to
EI-14, "Removal and Installation"
.
2.
Remove headlamp (LH/RH). Refer to
LT-40, "Removal and Installation"
3.
Remove air duct. Refer to
EM-19, "Removal and Installation"
(VQ35DE models),
(VK45DE models).
4.
Remove hood lock assembly, then remove hood lock cable. Refer to
BL-18, "Removal and Installation of
5.
Remove washer tank. Refer to
WW-48, "Removal and Installation of Washer Tank"
6.
Remove ambient sensor. Refer to
ATC-125, "Removal and Installation"
.
7.
Remove crash zone sensor. Refer to
SRS-49, "Removal and Installation"
1.
Headlamp (RH)
2.
Radiator core support side (RH)
3.
Washer tank
4.
Air guide (RH)
5.
Horn (High)
6.
Air guide (LH)
7.
Radiator core support side (LH)
8.
Horn (Low)
9.
Headlamp (LH)
10. Radiator core support center
11.
Upper radiator bracket (LH)
12. Upper radiator bracket (RH)
13. Power steering tube assembly
PIIB5804E
BL-22
RADIATOR CORE SUPPORT
8.
Remove air guide (LH/RH).
9.
Remove power steering tube assembly. Refer to
PS-44, "Removal and Installation"
.
10. Remove horn (High/Low). Refer to
WW-55, "Removal and Installation"
.
11. Remove mounting harness clip on radiator core support assembly, the harness is separate.
12. Remove ICC sensor integrated unit. Refer to
ACS-70, "ICC Sensor Integrated Unit"
.
13. Remove upper radiator bracket (LH/RH) with power tool.
14. Remove radiator core support side with power tool.
15. Remove radiator core support side (LH/RH) with power tool.
16. Remove radiator core support center.
CAUTION:
Put a wooden block under the radiator assembly to prevent
the radiator assembly from falling.
INSTALLATION
Install in the reverse order of removal.
PIIB3891J
PIIB3892J
PIIB3890J
FRONT FENDER
BL-23
C
D
E
F
G
H
J
K
L
M
A
B
BL
FRONT FENDER
PFP:63100
Removal and Installation
NIS001WO
REMOVAL
1.
Remove the front bumper. Refer to
EI-11, "Removal and Installation"
2.
LT-40, "Removal and Installation"
3.
Remove the turn signal lamp. Refer to
LT-229, "Removal and Installation of Front Turn Signal Lamp"
4.
Remove the front fender protector. Refer to
5.
Remove the center mud guard. Refer to
EI-22, "Removal and Installation"
6.
Remove the mounting bolt and remove the front fender.
CAUTION:
While removing use a shop cloth to protect body from damaging.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
After installing, apply touch-up paint (the body color) onto the head of the front fender mounting
bolts.
●
After installing, check front fender adjustment. Refer to
and
PIIB3893J
BL-24
POWER DOOR LOCK SYSTEM
POWER DOOR LOCK SYSTEM
PFP:24814
Component Parts and Harness Connector Location
NIS001WP
1.
Fuse block (J / B) fuse layout
2.
Fuse and fusible link box
3.
BCM M1, M2, M3 (View with instru-
ment lower panel RH removed)
4.
Front door lock actuator (Driver side)
D14
5.
Rear door lock actuator LH D59
6.
Power window main switch (door
lock and unlock switch) D10, D11
7.
Fuel lid lock actuator B477
PIIB5859E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст