Infiniti M35/M45 Y50. Manual — part 514
DTC P1550 BATTERY CURRENT SENSOR
EC-529
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between battery current sensor terminal 3 and ECM terminal 71.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E10, F1
●
Harness for open or short between battery current sensor and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK BATTERY CURRENT SENSOR
Refer to
EC-529, "Component Inspection"
OK or NG
OK
>> GO TO 9.
NG
>> Replace battery negative cable assembly.
9.
CHECK INTERMITTENT INCIDENT
Refer to
EC-153, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
Component Inspection
NBS0053X
BATTERY CURRENT SENSOR
1.
Reconnect harness connectors disconnected.
2.
Disconnect battery negative cable (1).
●
: To body ground
3.
Install jumper cable (A) between battery negative terminal and
body ground.
4.
Turn ignition switch ON.
Continuity should exist.
PBIB2724E
EC-530
[VQ35DE]
DTC P1550 BATTERY CURRENT SENSOR
5.
Check voltage between ECM terminal 71 (battery current sensor
signal) and ground.
6.
If NG, replace battery negative cable assembly.
Voltage: Approximately 2.5V
PBIB2617E
DTC P1551, P1552 BATTERY CURRENT SENSOR
EC-531
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P1551, P1552 BATTERY CURRENT SENSOR
PFP:294G0
Component Description
NBS0053Y
The power generation voltage variable control enables fuel con-
sumption to be decreased by reducing the engine load which is
caused by the power generation of the generator. The battery cur-
rent sensor (1) is installed to the battery cable at the negative termi-
nal. The sensor measures the charging/discharging current of the
battery. Based on the sensor signal, ECM judges whether or not the
power generation voltage variable control is performed. When per-
forming the power generation voltage variable control, ECM calcu-
lates the target power generation voltage based on the sensor
signal. And ECM sends the calculated value as the power genera-
tion command value to IPDM E/R. For the details of the power gen-
eration voltage variable control, refer to SC section.
CAUTION:
Do not connect the electrical component or the ground wire directly to the battery terminal. The con-
nection causes the malfunction of the power generation voltage variable control, and then the battery
discharge may occur.
CONSULT-II Reference Value in Data Monitor Mode
NBS0053Z
Specification data are reference values.
*: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
SC-5, "SPECIFIC GRAVITY CHECK"
On Board Diagnosis Logic
NBS00540
The MIL will not light up for this diagnosis.
NOTE:
If DTC P1551 or P1552 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Refer to
EC-486, "DTC P0643 SENSOR POWER SUPPLY"
PBIB2685E
MONITOR ITEM
CONDITION
SPECIFICATION
BAT CUR SEN
●
Engine speed: Idle
●
Battery: Fully charged*
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Approx. 2,600 - 3,500mV
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1551
1551
Battery current sensor circuit
low input
An excessively low voltage from the sen-
sor is sent to ECM.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Battery current sensor
P1552
1552
Battery current sensor circuit
high input
An excessively high voltage from the
sensor is sent to ECM.
EC-532
[VQ35DE]
DTC P1551, P1552 BATTERY CURRENT SENSOR
DTC Confirmation Procedure
NBS00541
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V with ignition
switch ON
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 10 seconds.
4.
If 1st trip DTC is detected, go to
EC-534, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF058Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст