Infiniti M35/M45 Y50. Manual — part 1137
TRANSFER ASSEMBLY
TF-55
C
E
F
G
H
I
J
K
L
M
A
B
TF
11. Install oil gutter to rear case.
CAUTION:
The tip of oil gutter should be put into rear case groove.
12. Install drive chain to front drive shaft.
CAUTION:
Identification mark of drive chain should be in the side of
front bearing of front drive shaft.
13. Install drive chain to mainshaft, and then install tap front drive
shaft with plastic hammer. Press-fit rear bearing of front drive
shaft to rear case.
CAUTION:
Be careful not to tap drive chain.
14. Install mainshaft bearing to front case, using the drift.
15. Install snap ring to front case.
CAUTION:
Do not reuse snap ring.
PDIA0261E
PDIA0284E
PDIA0257E
Tool number
: ST30621000 (J-25742-5)
PDIA0283E
PDIA0267E
TF-56
TRANSFER ASSEMBLY
16. Apply liquid gasket to mating surface of rear case.
●
Use Genuine Anaerobic Liquid Gasket or equivalent.
Refer to
GI-47, "Recommended Chemical Products and
CAUTION:
Remove old sealant adhering to mounting surfaces. Also
remove any moisture, oil, or foreign material adhering to
application and mounting surfaces.
17. Set front case to rear case.
CAUTION:
Be careful not to damage the mating surface transmission
side.
18. Tighten front case and rear case fixing bolts to the specified
torque. Refer to
.
19. Install spacer to mainshaft.
CAUTION:
Apply ATF to spacer.
SDIA2312E
PDIA0279E
Bolts symbol
Quantity
Bolt length “
” mm (in)
A
11
42 (1.65)
B
1
162 (6.38)
C
1
97 (3.82)
TORX bolts
1
40 (1.57)
PDIA0251E
PDIA0260E
TRANSFER ASSEMBLY
TF-57
C
E
F
G
H
I
J
K
L
M
A
B
TF
20. Install rear oil seal to rear case, using the drifts.
CAUTION:
●
Do not reuse rear oil seal.
●
Apply ATF to rear oil seal.
●
When installing, do not incline rear oil seal.
21. Install companion flange while align the matching mark of main-
shaft with the mark of companion flange.
22. Tighten self-lock nut to the specified torque, with flange wrench.
Refer to
CAUTION:
Do not reuse self-lock nut.
23. Install mainshaft oil seal until it is flush with end face of front
case, using the drift.
CAUTION:
●
Do not reuse mainshaft oil seal.
●
Apply ATF to mainshaft oil seal.
●
When installing, do not incline mainshaft oil seal.
24. Install front oil seal until it is flush with end face of front case,
using the drift.
CAUTION:
●
Do not reuse front oil seal.
●
Apply ATF to front oil seal.
●
When installing, do not incline front oil seal.
25. Apply sealant to threads of drain plug. Then install it to rear case
and tighten to the specified torque. Refer to
Dimension A
: 6.7 - 7.3 mm (0.264 - 0.287 in)
Tool number
A: ST30720000 (J-25405)
B: KV40104830 (
—
)
PDIA0281E
SDIA2378E
SDIA2369E
Tool number
: ST30720000 (J-25405)
PDIA0282E
Tool number
: ST27862000 (
—
)
PDIA0287E
TF-58
TRANSFER ASSEMBLY
●
Use Genuine Silicone RTV or equivalent. Refer to
GI-47, "Recommended Chemical Products and
CAUTION:
Remove old sealant and oil adhering to threads.
26. Set gasket to filler plug. Install it to rear case and tighten to the specified torque. Refer to
CAUTION:
●
Do not reuse gasket.
●
After oil is filled, tighten filler plug to specified torque.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст