Infiniti M35/M45 Y50. Manual — part 1149
WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
WW
A
B
WW
WIPER, WASHER & HORN
PRECAUTION . . . . . . . . . . . . . . . 3
FRONT WIPER AND WASHER SYSTEM . . . . .. 4
CHECK POWER SUPPLY AND GROUND CIR-
CUIT . . . . . . . . . . . . . . . . . 24
CONSULT-II Functions (BCM) . . . . . . . ... 25
CONSULT-II Functions (IPDM E/R) . . . . . ... 27
Removal and Installation of Front Wiper Drive
Assembly . . . . . . . . . . . . . . . . 44
REMOVAL . . . . . . . . . . . . . . ... 44
INSTALLATION . . . . . . . . . . . . ... 44
Disassembly and Assembly of Front Wiper Drive
Assembly . . . . . . . . . . . . . . . . 44
DISASSEMBLY . . . . . . . . . . . . ... 45
ASSEMBLY . . . . . . . . . . . . . . . 45
REMOVAL . . . . . . . . . . . . . . ... 46
INSTALLATION . . . . . . . . . . . . ... 46
WW-2
CHECK VALVE INSPECTION . . . . . . . . 47
REMOVAL . . . . . . . . . . . . . . ... 47
INSTALLATION . . . . . . . . . . . . . 47
Removal and Installation of Washer Tank . . . .. 48
REMOVAL . . . . . . . . . . . . . . ... 48
INSTALLATION . . . . . . . . . . . . . 48
Removal and Installation of Washer Pump . . . . 49
REMOVAL . . . . . . . . . . . . . . ... 49
INSTALLATION . . . . . . . . . . . . . 49
CIGARETTE LIGHTER . . . . . . . . . . . . 50
Wiring Diagram — CIGAR — . . . . . . . . . 50
Removal and Installation . . . . . . . . . . 51
REMOVAL . . . . . . . . . . . . . . ... 51
INSTALLATION . . . . . . . . . . . . . 51
POWER SOCKET . . . . . . . . . . . . . .52
REMOVAL . . . . . . . . . . . . . . . 53
INSTALLATION . . . . . . . . . . . . . 53
Removal and Installation of Center Console Box
Rear Side Power Socket . . . . . . . . . . .53
REMOVAL . . . . . . . . . . . . . . . 53
INSTALLATION . . . . . . . . . . . . . 53
HORN . . . . . . . . . . . . . . . . . . 54
Wiring Diagram — HORN — . . . . . . . . ..54
Removal and Installation . . . . . . . . . . .55
REMOVAL . . . . . . . . . . . . . . . 55
INSTALLATION . . . . . . . . . . . . . 55
PRECAUTION
WW-3
C
D
E
F
G
H
I
J
L
M
A
B
WW
PRECAUTION
PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS003WA
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
WW-4
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM
PFP:28810
Components Parts and Harness Connector Location
NKS003WB
System Description
NKS003WC
●
Front wiper relays (HIGH, LOW) are included in IPDM E/R (intelligent power distribution module engine
room).
●
Front wiper reverse relay is included in relay box-1. Refer to
PG-98, "ELECTRICAL UNITS LOCATION"
●
Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input termi-
nals. Terminal combination status is read by BCM (body control module) when switch is turned ON.
●
BCM controls front wiper LO, HI, and INT (intermittent) operation.
●
IPDM E/R operates wiper motor according to CAN communication signals from BCM.
●
Front wiper motor switches LOW speed to/from HIGH speed by BCM function to change polarity.
OUTLINE
Power is supplied at all times
●
to ignition relay, located in IPDM E/R, from battery directly,
●
through 50 A fusible link (letter F, located in fuse and fusible link block)
●
to BCM terminal 55,
●
through 10 A fuse [No. 21, located in fuse block (J/B)]
●
to BCM terminal 42,
●
through 30 A fuse (No. 73, located in IPDM E/R)
●
to front wiper low relay, located in IPDM E/R
●
to front wiper reverse relay terminal 5,
●
through 15 A fuse (No. 78, located in IPDM E/R)
PKID0472E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст