Infiniti M35/M45 Y50. Manual — part 934
INTERIOR ROOM LAMP
LT-281
C
D
E
F
G
H
I
J
L
M
A
B
LT
How to Perform Trouble Diagnoses
NKS003T5
1.
Confirm the symptom or customer complaint.
2.
Understand operation description and function description. Refer to
.
3.
Perform the Preliminary Check. Refer to
4.
Check symptom and repair or replace the cause of malfunction.
5.
Does the interior room lamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
6.
INSPECTION END
52
B
Ground
ON
—
Approx. 0 V
55
W
Battery power
supply
OFF
—
Battery voltage
57
SB
Trunk switch
signal
OFF
Trunk room lamp
switch
ON (open)
Approx. 0 V
OFF (close)
Battery voltage
62
V
Front door switch
driver side signal
OFF
Front door switch
driver side
ON (open)
Approx. 0 V
OFF (closed)
Approx. 7.5 - 8.0 V
63
R/G
Rear door switch
LH signal
OFF
Rear door switch LH
ON (open)
Approx. 0 V
OFF (closed)
Approx. 7.5 - 8.0 V
Terminal
No.
Wire
color
Signal name
Measuring condition
Reference value
Ignition
switch
Operation or condition
PKIB4960J
PKIB4960J
LT-282
INTERIOR ROOM LAMP
Preliminary Check
NKS003T6
CHECK POWER SUPPLY AND GROUND CIRCUIT
1.
CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
LT-273, "Wiring Diagram — ROOM/L —"
.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse or fusible link is blown, be sure to eliminate cause of malfunction before installing new fuse
PG-3, "POWER SUPPLY ROUTING CIRCUIT"
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK
>> INSPECTION END
NG
>> Repair harness or connector.
Unit
Power source
Fuse or fusible link No.
BCM
Battery
F
21
Ignition switch ON or START position
1
Ignition switch ACC or ON position
6
Key slot
Battery
22
Terminal
Ignition switch position
(+)
(
−
)
OFF
ACC
ON
BCM
connector
Terminal
M1
11
Ground
Approx.
0 V
Battery
voltage
Battery
voltage
38
Approx.
0 V
Approx.
0 V
Battery
voltage
M2
42
Battery
voltage
Battery
voltage
Battery
voltage
55
Battery
voltage
Battery
voltage
Battery
voltage
PKIA5204E
BCM connector
Terminal
Ground
Continuity
M2
52
Yes
SKIB5125E
INTERIOR ROOM LAMP
LT-283
C
D
E
F
G
H
I
J
L
M
A
B
LT
CONSULT-II Functions (BCM)
NKS003T7
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION
Refer to
GI-38, "CONSULT-II Start Procedure"
.
WORK SUPPORT (INT LAMP)
Operation Procedure
1.
Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “SET I/L D
−
UNLCK INTCON” on “SELECT WORK ITEM” screen.
4.
Touch “START”.
5.
Touch “CHANGE SETT”.
6.
The setting will be changed and “CUSTOMIZING COMPLETED ” will be displayed.
7.
Touch “END”.
Display Item List
NOTE:
Factory setting
BCM diagnosis part
Diagnosis mode
Description
INTERIOR LAMP
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending driving signal to them.
BATTERY SAVER
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending driving signal to them.
BCM
SELF-DIAG RESULTS
BCM performs self-diagnosis of CAN communication.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
Item
Description
CONSULT-II
ROOM LAMP TIMER SET
The lighting time can be selected when the interior room lamps are unlocked by
Intelligent Key or any door request switch.
●
Mode 1 (0 sec.)/Mode 2 (7.5 sec.)/Mode 3
NOTE
(15 sec.)/Mode 4 (30 sec.)
MODE 1 – 4
SET I/L D
−
UNLCK INTCON
Room lamp timer operation can be selected.
●
ON
NOTE
(Room lamp timer operates)/OFF (Room lamp timer does not oper-
ates)
ON/OFF
ROOM LAMP ON TIME SET
The time to escalate illumination can be selected when the interior room lamp is
turned on.
●
Mode 1 (0.5 sec.)/Mode 2
NOTE
(1 sec.)/Mode 3 (2 sec.)/Mode 4 (3 sec.)/
Mode 5 (4 sec.)/Mode 6 (5 sec.)/Mode 7 (0 sec.)
MODE 1 – 7
ROOM LAMP OFF TIME SET
The time to diminish illumination can be selected when the interior room lamp is
turned off.
●
Mode 1 (0.5 sec.)/Mode 2 (1 sec.)/Mode 3 (2 sec.)/Mode 4
NOTE
(3 sec.)/
Mode 5 (4 sec.)/Mode 6 (5 sec.)/Mode 7 (0 sec.)
MODE 1 – 7
R LAMP TIMER LOGIC SET
The lighting condition of room lamp timer can be selected when the door is
opened/closed.
●
Mode 1
NOTE
(Connected with all doors)/Mode 2 (Connected with driver door
only)
MODE 1 – 2
ROOM LAMP ON AT LOCK
The connected operation with room lamp timer can be selected when engine
switch (push switch) is turned OFF.
●
ON
NOTE
(Connected with room lamp timer operation) /OFF (Disconnected with
room lamp operation)
ON/OFF
LT-284
INTERIOR ROOM LAMP
DATA MONITOR (INT LAMP)
Operation Procedure
1.
Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4.
When “SELECTION FROM MENU” is selected, touch items to be monitored. When “ALL SIGNALS” is
selected, all the items will be monitored.
5.
Touch “START”.
6.
Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
Display Item List
NOTE:
This item is displayed, but cannot be monitored.
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects items and monitor them.
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays “IGN ON position (ON)/OFF, ACC position (OFF)” judged from the ignition switch
signal.
ACC ON SW
“ON/OFF”
Displays “IGN ACC, ON position (ON)/OFF position (OFF)” status judged from the key
switch signal.
KEY ON SW
“ON/OFF”
Displays “Intelligent Key inserted into key slot (ON)/Intelligent Key removed from key slot
(OFF)” status judged from the key switch signal.
DOOR SW - DR
“ON/OFF”
Displays status of the driver door as judged from the driver door switch signal. (door is open:
ON/door is closed: OFF)
DOOR SW - AS
“ON/OFF”
Displays “door open (ON)/door closed (OFF)” status, determined from passenger door
switch signal.
DOOR SW - RR
“ON/OFF”
Displays “door open (ON)/door closed (OFF)” status, determined from rear door switch RH
signal.
DOOR SW - RL
“ON/OFF”
Displays “door open (ON)/door closed (OFF) ” status, determined from rear door switch LH
signal.
BACK DOOR SW
NOTE
“OFF”
—
CDL LOCK SW
“ON/OFF”
Displays “door locked (ON)/other (OFF) status, determined from central door lock switch
LOCK signal.
CDL UNLOCK SW
“ON/OFF”
Displays “door unlocked (ON)/other (OFF)” status, determined from central door lock switch
UNLOCK signal.
KEY CYL LK - SW
“ON/OFF”
Displays ”door locked (ON)” status, determined from key cylinder switch in driver door.
KEY CYL UN - SW
“ON/OFF”
Displays “door unlocked (OFF)” status, determined from key cylinder switch in driver door.
I - KEY LOCK
“ON/OFF”
Displays “locked (ON)/other (OFF)” status, determined from lock signal.
I - KEY UNLOCK
“ON/OFF”
Displays “unlocked (ON)/other (OFF)” status, determined from unlock signal.
TRNK/HAT MNTR
“ON/OFF”
Displays “trunk open (ON)/trunk close (OFF)” status, determined from trunk room lamp
switch.
I - KEY DR UNLK
“ON/OFF”
Displays “ON” when only driver door is unlocked or “OFF” other cases by intelligent Key or
any door request switch, determined from unlock signal.
I - KEY AS UNLK
“ON/OFF”
Displays “unlocked (ON)/locked (OFF)” states of passenger door by passenger side door
request switch, determined from unlock signal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст